Implement LSI53C895A quirks exposed by OpenServer (Justin Chevrier).

After going through the debug log and scratching my head for quite some
time. I found the following:

The problem was with this block move:

lsi_scsi: SCRIPTS dsp=0fae8e50 opcode 01000028 arg 00f63c40
lsi_scsi: DMA addr=0x00f63c40 len=36

The number of bytes to be transferred (len) should be 40 which corresponds
to the block transfer of length 0x28 (from opcode 01000028). Instead we
have a length of 36 (0x24). The code responsible for this is (in
'lsi_do_dma'):

if (count > s->current_dma_len)
   count = s->current_dma_len;

Basically we're overwriting the length 40 with the value 36 which I
think we just left over in that variable from an earlier transfer. In my
patch below I initialize s->current_dma_len to s->dbc before we begin
the DMA transfer during Data In phase.

The attached patch gets Openserver 5.0.5 past the hardware detection
(and it lists the hard drive to boot, woohoo). It appears to stop a
little while later (doesn't seem SCSI related), but it's been so long since
I've booted Openserver I'm not sure what's supposted to happen after the HW
detection using the boot/root disks.

Props go to Craig Ringer for the initial post and the code that he posted
some of which is in this patch.


git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5706 c046a42c-6fe2-441c-8c8c-71466251a162

1 files changed, 22 insertions, 2 deletions

diff --git a/hw/lsi53c895a.c b/hw/lsi53c895a.c
index 53a2add0d..3f6783734 100644
--- a/hw/lsi53c895a.c
+++ b/hw/lsi53c895a.c
@@ -209,6 +209,7 @@ typedef struct {
     uint8_t mbox0;
     uint8_t mbox1;
     uint8_t dfifo;
+    uint8_t ctest2;
     uint8_t ctest3;
     uint8_t ctest4;
     uint8_t ctest5;
@@ -280,6 +281,7 @@ static void lsi_soft_reset(LSIState *s)
     s->mbox0 = 0;
     s->mbox1 = 0;
     s->dfifo = 0;
+    s->ctest2 = 0;
     s->ctest3 = 0;
     s->ctest4 = 0;
     s->ctest5 = 0;
@@ -890,6 +892,7 @@ again:
             break;
         case PHASE_DI:
             s->waiting = 2;
+            s->current_dma_len = s->dbc;
             lsi_do_dma(s, 0);
             if (s->waiting)
                 s->waiting = 3;
@@ -1279,7 +1282,7 @@ static uint8_t lsi_reg_readb(LSIState *s, int offset)
     case 0x19: /* CTEST1 */
         return 0;
     case 0x1a: /* CTEST2 */
-        tmp = LSI_CTEST2_DACK | LSI_CTEST2_CM;
+        tmp = s->ctest2 | LSI_CTEST2_DACK | LSI_CTEST2_CM;
         if (s->istat0 & LSI_ISTAT0_SIGP) {
             s->istat0 &= ~LSI_ISTAT0_SIGP;
             tmp |= LSI_CTEST2_SIGP;
@@ -1327,6 +1330,8 @@ static uint8_t lsi_reg_readb(LSIState *s, int offset)
         s->sist1 = 0;
         lsi_update_irq(s);
         return tmp;
+    case 0x46: /* MACNTL */
+        return 0x0f;
     case 0x47: /* GPCNTL0 */
         return 0x0f;
     case 0x48: /* STIME0 */
@@ -1440,6 +1445,9 @@ static void lsi_reg_writeb(LSIState *s, int offset, uint8_t val)
            SCRIPTS register move instructions are.  */
         s->sfbr = val;
         break;
+    case 0x0a: case 0x0b: 
+        /* Openserver writes to these readonly registers on startup */
+	return;    
     case 0x0c: case 0x0d: case 0x0e: case 0x0f:
         /* Linux writes to these readonly registers on startup.  */
         return;
@@ -1469,6 +1477,9 @@ static void lsi_reg_writeb(LSIState *s, int offset, uint8_t val)
     case 0x17: /* MBOX1 */
         s->mbox1 = val;
         break;
+    case 0x1a: /* CTEST2 */
+	s->ctest2 = val & LSI_CTEST2_PCICIE;
+	break;
     case 0x1b: /* CTEST3 */
         s->ctest3 = val & 0x0f;
         break;
@@ -1869,12 +1880,21 @@ void *lsi_scsi_init(PCIBus *bus, int devfn)
         return NULL;
     }
 
+    /* PCI Vendor ID (word) */
     s->pci_dev.config[0x00] = 0x00;
     s->pci_dev.config[0x01] = 0x10;
+    /* PCI device ID (word) */
     s->pci_dev.config[0x02] = 0x12;
     s->pci_dev.config[0x03] = 0x00;
+    /* PCI base class code */
     s->pci_dev.config[0x0b] = 0x01;
-    s->pci_dev.config[0x3d] = 0x01; /* interrupt pin 1 */
+    /* PCI subsystem ID */
+    s->pci_dev.config[0x2e] = 0x00;
+    s->pci_dev.config[0x2f] = 0x10;
+    /* PCI latency timer = 255 */
+    s->pci_dev.config[0x0d] = 0xff;
+    /* Interrupt pin 1 */
+    s->pci_dev.config[0x3d] = 0x01;
 
     s->mmio_io_addr = cpu_register_io_memory(0, lsi_mmio_readfn,
                                              lsi_mmio_writefn, s);