aboutsummaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2021-02-07ngff-breakout: update sch, brd and BOM to current production run of v3ngff-v3Martin Schramm3-462/+433
2021-01-29ngff-breakout: improve GND around 4th MHF4-SMA sectionMartin Schramm1-3/+18
2021-01-11ngff-breakout: update eBoM towards v3Martin Schramm1-101/+83
2021-01-11ngff-breakout: remove solder cream for SMT stand-off GND areaMartin Schramm2-679/+198
...means screws from both sides, but enables changing to either position for 3042 and 3052 cards
2021-01-11ngff-breakout: add BOM attributes for 2.45mm stand-off and M.2 connMartin Schramm2-97/+97
2020-11-09ngff-breakout: commit a v3 candidate for 3042 and 3052 cardsMartin Schramm2-2512/+3957
* PCBA now supports 3042 and 3052 M.2/NGFF cards * PCBA is now 100 m taller * fourth MHf4-SMA connector combination w/ TVS
2020-11-01initial design for DUS LMT breakout boardHarald Welte2-0/+1035
2020-10-17siu-clock-breakout: export PDF filesHarald Welte2-0/+0
2020-10-14clock-generator: Add 'export' version of frontpanel (mirrored)Harald Welte1-0/+4322
2020-10-14add export DXF for production (mirrored)Harald Welte1-0/+3410
2020-10-14siu-clock-breakout-frontpanel: Fix layer associationHarald Welte1-6/+6
2020-10-10clock-converter: add TFP 4 outline to frontpanelJoachim Steiger1-42/+482
2020-10-09clock-generator-frontpanel: Fix spacing of panel mount cut-outsHarald Welte1-72/+72
they must not be symmetric, but in multiple of 5.08mm
2020-10-09clock-generator: Add actual "TFP 7" outlineHarald Welte1-69/+589
2020-10-09siu-clock-breakout: Add actual fischer TFP 4 outlineHarald Welte1-35/+475
2020-10-09clock-converter/clock-generator frontpanelsJoachim Steiger2-0/+7696
layout generated from eagle to dxf and transferring the measurements. no outline yet (needs offset pcb border to frontpanel corner)
2020-10-08siu-clock-breakout frontpanelJoachim Steiger1-0/+3334
layout generated from eagle to dxf and measurements and datasheets no outline yet. (offset frontpanel border to pcb-border)
2020-09-10mpcie-breakout: Remove GND via underneath U.FL connectorsHarald Welte2-6/+41
2020-09-08sfp-breakout: BOM: update L1, L2 typeMartin Schramm1-12/+36
2020-08-15RJ45 jumper box designHarald Welte2-0/+1108
2020-07-27siu-clock-breakout: Add missing component valuesHarald Welte2-10/+10
2020-07-24clk-gen: commit GPIO pinsheet for SAMD21E in clk-gen v2 (solves OS#4656)Martin Schramm1-0/+878
... in Gnumeric format
2020-07-17add SIU clock breakout board designHarald Welte2-0/+6002
This board contains a 10P10C connector in the same pin-out as the Ericsson SIU-02 together with some differential receivers/drivers to convert the 1PPS from/to single-ended signals.
2020-07-07clock-generator: create updated sch + brd views, purge old dataMartin Schramm5-0/+0
2020-07-07clock-generator: purge old v1 eBOMMartin Schramm1-727/+0
2020-07-07clock-generator: upd ext'd BOM attributes and update v2 eBOMMartin Schramm3-137/+1228
2020-06-10sfp-experimenter: update ext'd attribs and BOMMartin Schramm3-345/+341
2020-06-10sfp-experimenter: update SFP cage part numberMartin Schramm1-6/+4
2020-06-08clock-generator: update schematics pdfMartin Schramm1-0/+0
2020-06-04gtm900-bo: purge unused layers in schema + boardMartin Schramm2-15/+0
2020-06-04gtm900-bo: exchange main LDO's BOM attributesMartin Schramm4-65/+85
Although the correct name was given in the schematic (MCP1827T-ADJE/ET), the BOM contained an LD1085, which is part of the same library... Now the extended attributes also reflect the correct part.
2020-06-01gtm900-bo: update parts to avail @Digikey, upd all ext'd attribsMartin Schramm4-922/+1123
... in sch and brd too
2020-05-27gtm900-bo: add SMT spacer as mechanical BOM-only partsMartin Schramm2-140/+175
2020-05-27gtm900-bo: complete v1 eBOM + export as gnumeric and xls formatMartin Schramm2-0/+910
2020-05-22gtm900-bo: add header for power source selection (DC in / USB)gtm900-v1Martin Schramm2-360/+528
2020-05-22gtm900-bo: ease some part's distances, increase OSHW logoMartin Schramm2-173/+190
2020-05-19gtm900-bo: re-introduce serial 0R on UART_RIMartin Schramm3-261/+308
...not, that it was needed, but just in case...
2020-05-18gtm900-bo: ERC + DRC done + correctionsMartin Schramm2-75/+111
2020-05-18gtm900-bo: routing done, no airwires left, mirrored FPC removedMartin Schramm2-541/+222
2020-05-17gtm900-bo: hopefully incorporating all we discussed last weeksMartin Schramm2-2543/+7222
see OS#4030
2020-04-27gtm900: added CP2105 and 3.5mm TRRS audio jack, remv'd aux connMartin Schramm3-1132/+3623
adds to OS#4030
2020-04-20initial commit for a GTM900 breakout PCBAMartin Schramm3-0/+19402
An additional mirrored FPC header will still be maintained as long as this PCBA is discussed/revised. This is going to be a OSHW CC-BY-SA.
2020-03-01clock-generator: Fix VDD connection of TC2050 SWD connectorHarald Welte2-10/+11
Closes: OS#4431
2020-02-07clock-gen: increase I2C PU's to 4k7Martin Schramm2-24/+24
Although the SI5153 datasheet mentions the I2C PUs as ">=1k", this appears to be unusually strong for no obvious reason, and we don't have high data rates there... changed them to more reasonable 4k7.
2020-01-31clock-gen: update ATSAMD21's BOM attributes (solves OS#4387)Martin Schramm2-23/+23
2020-01-30clock-generator: exchange mini-USB foorprint (solves OS#4386)Martin Schramm2-191/+63
... and purge unneeded layers
2020-01-28clock-generator: exchange silk screen position of R14 vs. C19Martin Schramm1-2/+2
fortunately, they have a different size (0603 vs 0402), so while placing this be#came obvious.
2020-01-09Merge branch 'master' of ssh://git.osmocom.org/osmo-small-hardwareMartin Schramm2-0/+0
2020-01-09ngff: add product links to all one- and two-row 2,54mm pin headerMartin Schramm2-47/+708
2019-12-14add PDF renderings of ngff-breakoutHarald Welte2-0/+0
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-21 21:16:07 +0000