Massive naming fix: STMPE11->STMPE811

git-svn-id: https://nuttx.svn.sourceforge.net/svnroot/nuttx/trunk@4782 7fd9a85b-ad96-42d3-883c-3090e2eb8679

1 files changed, 36 insertions, 36 deletions

diff --git a/nuttx/configs/stm3240g-eval/nxwm/defconfig b/nuttx/configs/stm3240g-eval/nxwm/defconfig
index c449042e65..38739b35bb 100644
--- a/nuttx/configs/stm3240g-eval/nxwm/defconfig
+++ b/nuttx/configs/stm3240g-eval/nxwm/defconfig
@@ -956,66 +956,66 @@ CONFIG_INPUT=y
 CONFIG_INPUT_TSC2007=n
 
 #
-# STMPE11 input device configuration
+# STMPE811 input device configuration
 #
 # Prerequisites:  CONFIG_INPUT=y
 # Other settings that effect the driver: CONFIG_DISABLE_POLL
 #
-# CONFIG_INPUT_STMPE11
-#   Enables support for the STMPE11 driver (Needs CONFIG_INPUT)
-# CONFIG_STMPE11_SPI
+# CONFIG_INPUT_STMPE811
+#   Enables support for the STMPE811 driver (Needs CONFIG_INPUT)
+# CONFIG_STMPE811_SPI
 #   Enables support for the SPI interface (not currenly supported)
-# CONFIG_STMPE11_I2C
+# CONFIG_STMPE811_I2C
 #   Enables support for the I2C interface
-# CONFIG_STMPE11_MULTIPLE
-#   Can be defined to support multiple STMPE11 devices on board.
-# CONFIG_STMPE11_ACTIVELOW
+# CONFIG_STMPE811_MULTIPLE
+#   Can be defined to support multiple STMPE811 devices on board.
+# CONFIG_STMPE811_ACTIVELOW
 #   Interrupt is generated by an active low signal (or falling edge).
-# CONFIG_STMPE11_EDGE
+# CONFIG_STMPE811_EDGE
 #   Interrupt is generated on an edge (vs. on the active level)
-# CONFIG_STMPE11_NPOLLWAITERS
+# CONFIG_STMPE811_NPOLLWAITERS
 #   Maximum number of threads that can be waiting on poll() (ignored if
 #   CONFIG_DISABLE_POLL is set).
-# CONFIG_STMPE11_TSC_DISABLE
+# CONFIG_STMPE811_TSC_DISABLE
 #   Disable driver touchscreen functionality.
-# CONFIG_STMPE11_ADC_DISABLE
+# CONFIG_STMPE811_ADC_DISABLE
 #   Disable driver ADC functionality.
-# CONFIG_STMPE11_GPIO_DISABLE
+# CONFIG_STMPE811_GPIO_DISABLE
 #   Disable driver GPIO functionality.
-# CONFIG_STMPE11_GPIOINT_DISABLE
+# CONFIG_STMPE811_GPIOINT_DISABLE
 #   Disable driver GPIO interrupt functionality (ignored if GPIO functionality is
 #   disabled).
-# CONFIG_STMPE11_SWAPXY
+# CONFIG_STMPE811_SWAPXY
 #   Reverse the meaning of X and Y to handle different LCD orientations.
 #   For the STM3240G-EVAL, X and Y should be swapped in PORTRAIT modes
-# CONFIG_STMPE11_TEMP_DISABLE
+# CONFIG_STMPE811_TEMP_DISABLE
 #   Disable driver temperature sensor functionality.
-# CONFIG_STMPE11_REGDBUG
+# CONFIG_STMPE811_REGDBUG
 #   Enabled very low register-level debug output.  Requires CONFIG_DEBUG.
-# CONFIG_STMPE11_THRESHX and CONFIG_STMPE11_THRESHY
-#   STMPE11 touchscreen data comes in a a very high rate.  New touch positions
+# CONFIG_STMPE811_THRESHX and CONFIG_STMPE811_THRESHY
+#   STMPE811 touchscreen data comes in a a very high rate.  New touch positions
 #   will only be reported when the X or Y data changes by these thresholds.
 #   This trades reduces data rate for some loss in dragging accuracy.  The
-#   STMPE11 is configure for 12-bit values so the raw ranges are 0-4095. So
+#   STMPE811 is configure for 12-bit values so the raw ranges are 0-4095. So
 #   for example, if your display is 320x240, then THRESHX=13 and THRESHY=17
 #   would correspond to one pixel.  Default: 12
 #
-CONFIG_INPUT_STMPE11=y
-CONFIG_STMPE11_SPI=n
-CONFIG_STMPE11_I2C=y
-CONFIG_STMPE11_MULTIPLE=y
-CONFIG_STMPE11_ACTIVELOW=y
-CONFIG_STMPE11_EDGE=y
-#CONFIG_STMPE11_NPOLLWAITERS
-CONFIG_STMPE11_TSC_DISABLE=n
-CONFIG_STMPE11_ADC_DISABLE=y
-CONFIG_STMPE11_GPIO_DISABLE=y
-CONFIG_STMPE11_GPIOINT_DISABLE=y
-CONFIG_STMPE11_SWAPXY=n
-CONFIG_STMPE11_TEMP_DISABLE=y
-CONFIG_STMPE11_REGDEBUG=n
-CONFIG_STMPE11_THRESHX=39
-CONFIG_STMPE11_THRESHY=51
+CONFIG_INPUT_STMPE811=y
+CONFIG_STMPE811_SPI=n
+CONFIG_STMPE811_I2C=y
+CONFIG_STMPE811_MULTIPLE=y
+CONFIG_STMPE811_ACTIVELOW=y
+CONFIG_STMPE811_EDGE=y
+#CONFIG_STMPE811_NPOLLWAITERS
+CONFIG_STMPE811_TSC_DISABLE=n
+CONFIG_STMPE811_ADC_DISABLE=y
+CONFIG_STMPE811_GPIO_DISABLE=y
+CONFIG_STMPE811_GPIOINT_DISABLE=y
+CONFIG_STMPE811_SWAPXY=n
+CONFIG_STMPE811_TEMP_DISABLE=y
+CONFIG_STMPE811_REGDEBUG=n
+CONFIG_STMPE811_THRESHX=39
+CONFIG_STMPE811_THRESHY=51
 
 #
 # USB Device Configuration