14 files changed, 1373 insertions, 0 deletions
diff --git a/debian/changelog b/debian/changelog
new file mode 100644
index 0000000..029e9c8
--- /dev/null
+++ b/debian/changelog
@@ -0,0 +1,188 @@
+gr-osmosdr (0.1.5git) unstable; urgency=medium
+
+  * Add initial support for Airspy HF+
+  * Support for FreeSRP via libfreesrp
+
+ -- Harald Welte <laforge@gnumonks.org>  Sun, 03 Jun 2018 10:38:52 +0200
+
+gr-osmosdr (0.1.4-14) unstable; urgency=medium
+
+  * Add initial support for Airspy HF+
+  * Support for FreeSRP via libfreesrp
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Thu, 23 Nov 2017 10:38:52 -0500
+
+gr-osmosdr (0.1.4-13) unstable; urgency=medium
+
+  * update to v0.1.4-98-gc653754
+  * rtl-sdr bias-T support
+  * build with gnuradio-3.7.11
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Thu, 07 Sep 2017 19:50:05 -0400
+
+gr-osmosdr (0.1.4-12) unstable; urgency=medium
+
+  * rebuild with airspy-host 1.0.9
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Fri, 14 Oct 2016 20:58:28 -0400
+
+gr-osmosdr (0.1.4-11) unstable; urgency=medium
+
+  * Add SoapySDR support
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Sun, 28 Aug 2016 14:52:53 -0400
+
+gr-osmosdr (0.1.4-10) unstable; urgency=medium
+
+  * build with gnuradio-3.7.10
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Sun, 10 Jul 2016 12:41:34 -0400
+
+gr-osmosdr (0.1.4-9) unstable; urgency=medium
+
+  * update to v0.1.4-72-g164a09f
+  * rebuild on kfreebsd (Closes: #822132)
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Fri, 29 Apr 2016 05:10:35 -0400
+
+gr-osmosdr (0.1.4-8) unstable; urgency=medium
+
+  * update to v0.1.4-67-gac15e78, build with gnuradio 3.7.9
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Wed, 13 Jan 2016 00:16:06 -0500
+
+gr-osmosdr (0.1.4-7) unstable; urgency=medium
+
+  * Lintian cleanups pre-depends and dep5-copyright
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Sat, 28 Nov 2015 22:57:30 -0500
+
+gr-osmosdr (0.1.4-6) unstable; urgency=medium
+
+  * Don't depend upon hackrf on non-linux
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Mon, 05 Oct 2015 00:25:01 -0400
+
+gr-osmosdr (0.1.4-5) unstable; urgency=medium
+
+  * Rebuild with uhd 3.9.1-3
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Wed, 30 Sep 2015 21:06:49 -0400
+
+gr-osmosdr (0.1.4-4) unstable; urgency=medium
+
+  * Tighten libuhd003 versioned dependency via dh_makeshlibs
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Wed, 30 Sep 2015 01:04:40 -0400
+
+gr-osmosdr (0.1.4-3) unstable; urgency=low
+
+  * rebuild with uhd-3.9.1
+  * post gcc-5 libstdc++6 transition build (Closes: #791062)
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Mon, 14 Sep 2015 20:51:16 -0400
+
+gr-osmosdr (0.1.4-2) unstable; urgency=medium
+
+  * add watch file, rebuild with uhd-3.9.0
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Thu, 10 Sep 2015 10:55:58 -0400
+
+gr-osmosdr (0.1.4-1) unstable; urgency=medium
+
+  * New upstream, update to v0.1.4-48-g86ad584
+    build with gnuradio 3.7.8
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Sun, 16 Aug 2015 21:55:38 -0400
+
+gr-osmosdr (0.1.3-2) unstable; urgency=low
+
+  * Add versioned depends for bladerf (Closes: #759927)
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Wed, 10 Sep 2014 23:57:56 -0400
+
+gr-osmosdr (0.1.3-1) unstable; urgency=low
+
+  * New upstream release
+  * build with gnuradio 3.7.5
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Wed, 03 Sep 2014 22:21:12 -0400
+
+gr-osmosdr (0.1.2-1) unstable; urgency=low
+
+  * New upstream release, update to v0.1.2-2-g8604d76
+  * Include airspy support
+  * pkg-gr-osmosdr git for Debian packaging (Closes: #759268)
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Thu, 28 Aug 2014 14:37:08 -0400
+
+gr-osmosdr (0.1.1.4.ac95af2-1) unstable; urgency=low
+
+  * Update to v0.1.1-4-gac95af2
+    reverting 66109099 rtl: implement methods allowing runtime to control
+    sampling process
+  * Build with gnuradio 3.7.3 (Closes: #743392)
+  * Osmocom MiriSDR support
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Sat, 19 Apr 2014 19:22:49 -0400
+
+gr-osmosdr (0.1.0.55.80c4af-2~bpo70~1) wheezy-backports; urgency=low
+
+  * Rebuild for wheezy-backports.
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Tue, 11 Feb 2014 16:57:11 -0500
+
+gr-osmosdr (0.1.0.55.80c4af-2) unstable; urgency=low
+
+  * ship grc blocks
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Fri, 03 Jan 2014 00:32:28 -0500
+
+gr-osmosdr (0.1.0.55.80c4af-1) unstable; urgency=low
+
+  * New upstream commit, build with gnuradio 3.7.2.1
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Tue, 31 Dec 2013 00:09:54 -0500
+
+gr-osmosdr (0.1.0.11.04b4c8-3) unstable; urgency=low
+
+  * Fix up dependencies for current unstable build
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Thu, 12 Dec 2013 12:05:35 -0500
+
+gr-osmosdr (0.1.0.11.04b4c8-2) unstable; urgency=low
+
+  * drop bladerf dependency
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Sat, 23 Nov 2013 11:25:21 -0500
+
+gr-osmosdr (0.1.0.11.04b4c8-1) unstable; urgency=low
+
+  * New upstream snapshot (Closes: #726469)
+  * Match GNU Radio live distribution version
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Tue, 08 Oct 2013 17:30:31 -0400
+
+gr-osmosdr (0.1git59ceddb-1) unstable; urgency=low
+
+  * New upstream release, build with gnuradio 3.6.4.1-0wheezy1
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Wed, 01 May 2013 17:19:35 -0400
+
+gr-osmosdr (0.1gitd11b7a-1) unstable; urgency=low
+
+  * New upstream git, build with gnuradio 3.6.3
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Wed, 13 Feb 2013 15:56:33 -0500
+
+gr-osmosdr (0.1git0f25dae-1) unstable; urgency=low
+
+  * New upstream git, build with gnuradio 3.6.2
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Sun, 16 Sep 2012 20:47:39 -0400
+
+gr-osmosdr (0.0git7f796fe-1) unstable; urgency=low
+
+  * New upstream git, build with gnuradio 3.6.0
+
+ -- A. Maitland Bottoms <bottoms@debian.org>  Mon, 14 May 2012 20:28:18 -0400
diff --git a/debian/compat b/debian/compat
new file mode 100644
index 0000000..ec63514
--- /dev/null
+++ b/debian/compat
@@ -0,0 +1 @@
+9
diff --git a/debian/control b/debian/control
new file mode 100644
index 0000000..e779451
--- /dev/null
+++ b/debian/control
@@ -0,0 +1,79 @@
+Source: gr-osmosdr
+Section: libdevel
+Priority: optional
+Maintainer: Harald Welte <laforge@gnumonks.org>
+Build-Depends: cmake,
+               debhelper (>= 9.0.0~),
+	       dh-python,
+               doxygen,
+               gnuradio-dev (>=3.7.11),
+               gr-fcdproplus (>=3.7.25.4b6464b-3) [!hurd-i386],
+               gr-iqbal (>=0.37.2-8),
+               libairspy-dev (>= 1.0.9~) [!hurd-i386],
+               libairspyhf-dev [!hurd-i386],
+               libbladerf-dev (>=0.2016.01~rc1) [!hurd-i386],
+               libboost-dev,
+               libboost-system-dev,
+               libboost-thread-dev,
+	       libfreesrp-dev [!hurd-i386],
+               libhackrf-dev [linux-any],
+               liblog4cpp5-dev,
+               libmirisdr-dev [!hurd-i386],
+               libosmosdr-dev [!hurd-i386],
+               librtlsdr-dev [!hurd-i386],
+	       libsoapysdr-dev,
+               libuhd-dev (>=3.10),
+               pkg-config,
+               python-dev,
+	       python-soapysdr,
+               swig
+X-Python-Version: >= 2.7, << 2.8
+Standards-Version: 4.1.0
+Homepage: https://osmocom.org/projects/gr-osmosdr/wiki
+Vcs-Git: git://git.osmocom.org/gr-osmosdr
+Vcs-Browser: https://git.osmocom.org/gr-osmosdr
+
+Package: gr-osmosdr
+Architecture: any
+Pre-Depends: ${misc:Pre-Depends}
+Depends: ${misc:Depends}, ${python:Depends}, ${shlibs:Depends}
+Recommends: gnuradio, gr-fosphor
+Description: Gnuradio blocks from the OsmoSDR project
+ The Osmocom project is a family of projects regarding Open source
+ mobile communications.
+ .
+ While primarily being developed for the OsmoSDR hardware, this block
+ as well supports:
+  - FUNcube Dongle through libgnuradio-fcd
+  - FUNcube Dongle Pro+ through gr-fcdproplus
+  - sysmocom OsmoSDR Devices through libosmosdr
+  - RTL2832U based DVB-T dongles through librtlsdr
+  - RTL-TCP spectrum server (see librtlsdr project)
+  - MSi2500 based DVB-T dongles through libmirisdr
+  - gnuradio .cfile input through libgnuradio-blocks
+  - RFSPACE SDR-IQ, SDR-IP, NetSDR (incl. X2 option)
+  - Great Scott Gadgets HackRF through libhackrf
+  - Nuand LLC bladeRF through libbladeRF library
+  - Ettus USRP Devices through Ettus UHD library
+  - Fairwaves UmTRX through Fairwaves' fork of UHD
+  - AIRSPY Receiver
+  - AIRSPY HF+ Receiver
+  - SoapySDR support
+  - Red Pitaya SDR transceiver (http://bazaar.redpitaya.com)
+  - FreeSRP through libfreesrp
+ .
+ By using the OsmoSDR block you can take advantage of a common
+ software API in your application(s) independent of the underlying
+ radio hardware.
+
+Package: libgnuradio-osmosdr0.1.4
+Section: libs
+Architecture: any
+Pre-Depends: ${misc:Pre-Depends}
+Depends: ${misc:Depends}, ${shlibs:Depends}
+Multi-Arch: same
+Description: Gnuradio blocks from the OsmoSDR project - library
+ The Osmocom project is a family of projects regarding Open source
+ mobile communications.
+ .
+ This package contains the shared library.
diff --git a/debian/copyright b/debian/copyright
new file mode 100644
index 0000000..03e853f
--- /dev/null
+++ b/debian/copyright
@@ -0,0 +1,195 @@
+Format: http://www.debian.org/doc/packaging-manuals/copyright-format/1.0/
+Upstream-Name: gr-osmosdr
+Upstream-Contact: http://sdr.osmocom.org/trac/wiki/rtl-sdr
+Source:
+ git clone git://git.osmocom.org/gr-osmosdr
+ The upstream package source tarball was generated from the tag:
+ git archive --format=tar --prefix=gr-osmosdr-0.1.4/  v0.1.4 | xz > ../gr-osmosdr_0.1.4.orig.tar.xz
+Comment:
+ Debian packages by A. Maitland Bottoms <bottoms@debian.org>,
+ .
+ Upstream Author:
+ Dimitri Stolnikov <horiz0n@gmx.net>
+Copyright: 2012,2013 Dimitri Stolnikov <horiz0n@gmx.net>
+License: GPL-3+
+
+Files: COPYING
+Copyright: 2007 Free Software Foundation, Inc. <http://fsf.org/>
+License: FSF-COPYING
+ Everyone is permitted to copy and distribute verbatim copies
+ of this license document, but changing it is not allowed.
+
+Files: CMakeLists.txt apps/* docs/* python/* include/osmosdr/api.h
+ cmake/Modules/* include/osmosdr/CMakeLists.txt
+ lib/CMakeLists.txt lib/gnuradio-osmosdr.rc.in
+ lib/bladerf/CMakeLists.txt swig/* grc/CMakeLists.txt
+Copyright: 2005,2007-2013 Free Software Foundation, Inc.
+Comment: GNU Radio gr_modtool derived
+License: GPL-3+
+
+Files: debian/*
+Copyright: 2013 A. Maitland Bottoms <bottoms@debian.org>
+License: GPL-3+
+
+Files: grc/gen_osmosdr_blocks.py
+Copyright: 2012 Free Software Foundation, Inc.
+License: GPL-2+
+
+Files: include/osmosdr/pimpl.h include/osmosdr/ranges.h lib/ranges.cc
+ include/osmosdr/time_spec.h lib/time_spec.cc
+Copyright: 2010-2013 Ettus Research LLC
+License: GPL-3+
+
+FIles: lib/bladerf/bladerf_common.cc lib/bladerf/bladerf_common.h
+ lib/bladerf/bladerf_sink_c.cc lib/bladerf/bladerf_sink_c.h
+ lib/bladerf/bladerf_source_c.cc lib/bladerf/bladerf_source_c.h
+Copyright: 2013 Nuand LLC
+ 2013 Dimitri Stolnikov <horiz0n@gmx.net>
+License: GPL-3+
+
+Files: lib/soapy/*
+Copyright: 2015 Josh Blum <josh@joshknows.com>
+ 2013 Dimitri Stolnikov <horiz0n@gmx.net>
+License: GPL-3+
+
+Files: lib/freesrp/*
+Copyright: 2017 by Lukas Lao Beyer
+License: GPL-3+
+
+Files: AUTHORS MANIFEST.md README gnuradio-osmosdr.pc.in
+ cmake/cmake_uninstall.cmake.in include/osmosdr/device.h
+ include/osmosdr/sink.h include/osmosdr/source.h
+ lib/arg_helpers.h lib/config.h.in lib/device.cc
+ lib/sink_iface.h  lib/sink_impl.cc  lib/sink_impl.h
+ lib/source_iface.h  lib/source_impl.cc  lib/source_impl.h
+ lib/airspy/* lib/fcd/* lib/file/* lib/hackrf/*
+ lib/miri/* lib/osmosdr/* lib/rfspace/* lib/rtl*
+ lib/sdrplay/* lib/uhd/*
+Copyright: 2012-2013 Dimitri Stolnikov <horiz0n@gmx.net>
+License: GPL-3+
+
+Files: lib/rtl_tcp/rtl_tcp_source_f.h
+Copyright: 2012 Hoernchen <la@tfc-server.de>
+License: GPL-3+
+
+Files: lib/miri/miri_source_c.cc
+Copyright: 2012 Steve Markgraf <steve@steve-m.de>
+ 2012 Dimitri Stolnikov <horiz0n@gmx.net>
+License: GPL-3+
+
+Files: lib/redpitaya/*
+Copyright: 2015 Pavel Demin
+           2012,2015 Dimitri Stolnikov <horiz0n@gmx.net>
+License: GPL-3+
+
+Files: lib/freesrp/readerwriterqueue/*
+Copyright: 2013-2015, Cameron Desrochers
+Comment: libfreesrp includes ReaderWriterQueue
+License: Simplified-BSD
+ All rights reserved.
+ .
+ Redistribution and use in source and binary forms, with or without modification,
+ are permitted provided that the following conditions are met:
+ .
+ - Redistributions of source code must retain the above copyright notice, this list of
+   conditions and the following disclaimer.
+ - Redistributions in binary form must reproduce the above copyright notice, this list of
+   conditions and the following disclaimer in the documentation and/or other materials
+   provided with the distribution.
+ .
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY
+ EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
+ THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
+ OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
+ TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
+ EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+Files: lib/freesrp/readerwriterqueue/atomicops.h
+Copyright: 2015 Jeff Preshing
+License: atomicops
+ This software is provided 'as-is', without any express or implied
+ warranty. In no event will the authors be held liable for any damages
+ arising from the use of this software.
+ .
+ Permission is granted to anyone to use this software for any purpose,
+ including commercial applications, and to alter it and redistribute it
+ freely, subject to the following restrictions:
+ .
+ 1. The origin of this software must not be misrepresented; you must not
+    claim that you wrote the original software. If you use this software
+    in a product, an acknowledgement in the product documentation would be
+    appreciated but is not required.
+ 2. Altered source versions must be plainly marked as such, and must not be
+    misrepresented as being the original software.
+ 3. This notice may not be removed or altered from any source distribution.
+
+Files: cmake/Modules/CMakeParseArgumentsCopy.cmake
+Copyright: 2010 Alexander Neundorf <neundorf@kde.org>
+Comment: copy of CMakeParseArguments.cmake from cmake 2.8.x
+License: Kitware-BSD
+ All rights reserved.
+ .
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+ .
+ * Redistributions of source code must retain the above copyright
+   notice, this list of conditions and the following disclaimer.
+ .
+ * Redistributions in binary form must reproduce the above copyright
+   notice, this list of conditions and the following disclaimer in the
+   documentation and/or other materials provided with the distribution.
+ .
+ * Neither the names of Kitware, Inc., the Insight Software Consortium,
+   nor the names of their contributors may be used to endorse or promote
+   products derived from this software without specific prior written
+   permission.
+ .
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+License: GPL-2+
+ GNU Radio Companion is free software; you can redistribute it and/or
+ modify it under the terms of the GNU General Public License
+ as published by the Free Software Foundation; either version 2
+ of the License, or (at your option) any later version.
+ .
+ GNU Radio Companion is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+ .
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA
+ .
+ On Debian systems, the complete text of the GNU General Public
+ License (GPL) version 3 can be found in the file
+ '/usr/share/common-licenses/GPL-2'.
+
+License: GPL-3+
+ GNU Radio is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 3, or (at your option)
+ any later version.
+ .
+ GNU Radio is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+ .
+ On Debian systems, the complete text of the GNU General Public
+ License (GPL) version 3 can be found in the file
+ '/usr/share/common-licenses/GPL-3'.
diff --git a/debian/gr-osmosdr.install b/debian/gr-osmosdr.install
new file mode 100644
index 0000000..3434eae
--- /dev/null
+++ b/debian/gr-osmosdr.install
@@ -0,0 +1,6 @@
+usr/bin/*
+usr/include/*
+usr/lib/*/lib*.so
+usr/lib/*/pkgconfig/*
+usr/lib/python*
+usr/share/*
diff --git a/debian/gr-osmosdr.manpages b/debian/gr-osmosdr.manpages
new file mode 100644
index 0000000..ee5ccbe
--- /dev/null
+++ b/debian/gr-osmosdr.manpages
@@ -0,0 +1,4 @@
+debian/osmocom_fft.1
+debian/osmocom_siggen.1
+debian/osmocom_siggen_nogui.1
+debian/osmocom_spectrum_sense.1
diff --git a/debian/libgnuradio-osmosdr0.1.4.install b/debian/libgnuradio-osmosdr0.1.4.install
new file mode 100644
index 0000000..3ddde58
--- /dev/null
+++ b/debian/libgnuradio-osmosdr0.1.4.install
@@ -0,0 +1 @@
+usr/lib/*/lib*.so.*
diff --git a/debian/osmocom_fft.1 b/debian/osmocom_fft.1
new file mode 100644
index 0000000..0b24d71
--- /dev/null
+++ b/debian/osmocom_fft.1
@@ -0,0 +1,224 @@
+.TH osmocom_fft "1" "October 2013" "OSMOCOM" "User Commands"
+.SH NAME
+osmocom_fft \- Spectrum Browser
+.SH SYNOPSIS
+.B osmocom_fft
+[\fIoptions\fR]
+.SH DESCRIPTION
+Spectrum Browser
+.SH OPTIONS
+.TP
+\fB\-h\fR, \fB\-\-help\fR
+show this help message and exit
+.TP
+\fB\-a\fR ARGS, \fB\-\-args\fR=\fIARGS\fR
+Device args, [default=]
+.TP
+\fB\-A\fR ANTENNA, \fB\-\-antenna\fR=\fIANTENNA\fR
+Select RX antenna where appropriate
+.TP
+\fB\-s\fR SAMP_RATE, \fB\-\-samp\-rate\fR=\fISAMP_RATE\fR
+Set sample rate (bandwidth), minimum by default
+.TP
+\fB\-f\fR FREQ, \fB\-\-center\-freq\fR=\fIFREQ\fR
+Set frequency to FREQ
+.TP
+\fB\-c\fR FREQ_CORR, \fB\-\-freq\-corr\fR=\fIFREQ_CORR\fR
+Set frequency correction (ppm)
+.TP
+\fB\-g\fR GAIN, \fB\-\-gain\fR=\fIGAIN\fR
+Set gain in dB (default is midpoint)
+.TP
+\fB\-W\fR, \fB\-\-waterfall\fR
+Enable waterfall display
+.TP
+\fB\-S\fR, \fB\-\-oscilloscope\fR
+Enable oscilloscope display
+.TP
+\fB\-\-avg\-alpha\fR=\fIAVG_ALPHA\fR
+Set fftsink averaging factor, default=[0.1]
+.TP
+\fB\-\-averaging\fR
+Enable fftsink averaging, default=[False]
+.TP
+\fB\-\-ref\-scale\fR=\fIREF_SCALE\fR
+Set dBFS=0dB input value, default=[1.0]
+.TP
+\fB\-\-fft\-size\fR=\fIFFT_SIZE\fR
+Set number of FFT bins [default=1024]
+.TP
+\fB\-\-fft\-rate\fR=\fIFFT_RATE\fR
+Set FFT update rate, [default=30]
+.TP
+\fB\-v\fR, \fB\-\-verbose\fR
+Use verbose console output [default=False]
+.SH "SEE ALSO"
+The full documentation for
+.B linux;
+is maintained as a Texinfo manual.  If the
+.B info
+and
+.B linux;
+programs are properly installed at your site, the command
+.IP
+.B info linux;
+.PP
+should give you access to the complete manual.
+.SH Device specification
+You can specify the source or sink device using a comma separated string of argument=value pairs. The always-up-to-date block documentation with examples is available right here.
+.SH FCD Source
+.TP
+Argument
+Notes
+.TP
+fcd=<device-index>
+0-based device identifier, optional
+.TP
+device=hw:2
+overrides the audio device
+.TP
+type=2
+selects the dongle type, 1 for Classic, 2 for Pro+
+.LP
+The "device" argument overrides the audio device used by the underlying driver to access the dongle's IQ sample stream.
+.LP
+The "type" argument selects the dongle type, 1 for Classic, 2 for Pro+.
+.SH OsmoSDR Source
+.TP
+Argument
+Notes
+.TP
+osmosdr=<device-index>
+0-based device identifier
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.TP
+buflen=<length-of-buffer>
+Default is 256kB, must be multiple of 512
+.SH RTL-SDR Source
+.TP
+Argument
+Notes
+.TP
+rtl=<device-index>
+0-based device identifier OR serial number
+.TP
+rtl_xtal=<frequency>
+Frequency (Hz) used for the RTL chip, accepts eng notation
+.TP
+tuner_xtal=<frequency>
+Frequency (Hz) used for the tuner chip, accepts eng notation
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.TP
+buflen=<length-of-buffer>
+Default is 256kB, must be multiple of 512
+.TP
+direct_samp=0|1|2
+Enable direct sampling mode on the RTL chip. 0: Disable, 1: use I channel, 2: use Q channel
+.TP
+offset_tune=0|1
+Enable offset tune mode for E4000 tuners
+.LP
+NOTE: use rtl_eeprom -s to program your own serial number to the device
+.LP
+NOTE: if you don't specify rtl_xtal/tuner_xtal, the underlying driver will use 28.0MHz
+.SH RTL-SDR TCP Source
+.TP
+Argument
+Notes
+.TP
+rtl_tcp=<hostname>:<port>
+hostname defaults to "localhost", port to "1234"
+.TP
+psize=<payload-size>
+Default is 16384 bytes
+.TP
+direct_samp=0|1|2
+Enable direct sampling mode on the RTL chip 0=Off, 1=I-ADC input enabled, 2=Q-ADC input enabled
+.TP
+offset_tune=0|1
+Enable offset tune mode for E4000 tuners 
+.SH Miri Source
+.TP
+Argument
+Notes
+.TP
+miri=<device-index>
+0-based device identifier
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.SH UHD Source / Sink
+Argument
+Notes
+.TP
+uhd
+Use this argument without a value
+.TP
+nchan=<channel-count>
+For multichannel USRP configurations use the subdev parameter to specify stream mapping
+.TP
+subdev=<subdev-spec>
+Examples: "A:0", "B:0", "A:0 B:0" when nchan=2. Refer original ettus documentation on this
+.TP
+lo_offset=<frequency>
+Offset frequency in Hz, must be within daughterboard bandwidth. Accepts eng notation
+.LP
+Additional argument/value pairs will be passed to the underlying driver, for more information see specifying the subdevice and common device identifiers in the Ettus documentation.
+.SH bladeRF Source / Sink
+.TP
+Argument
+Notes
+.TP
+bladerf[=0]
+0-based device identifier (optional)
+.TP
+fw='/path/to/the/firmware.img'
+program MCU firmware from given file. usually not needed. power cycle required.
+.TP
+fpga='/path/to/the/bitstream.rbf'
+load FPGA bitstream from given file. required only at first run at the moment.
+.SH HackRF Source / Sink
+.TP
+Argument
+Notes
+.TP
+hackrf
+Use this argument without a value
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.LP
+Only the first device found may be used at the moment because of libhackrf limitation.
+.LP
+Transmit support has been verified by using the crc-mmbTools DAB sdr transmitter.
+.SH IQ File Source
+.TP
+Argument
+Notes
+.TP
+file=<path-to-file-name>	
+.TP
+freq=<frequency>
+Center frequency in Hz, accepts eng notation
+.TP
+rate=<sampling-rate>
+Mandatory, in samples/s, accepts eng notation
+.TP
+repeat=true|false
+Default is true
+.TP
+throttle=true|false
+Throttle flow of samples, default is true
+.SH EXAMPLES
+.LP
+osmocom_fft -a rtl=0 -v -f 100e6 -s 2.4e6 -g 15
+.LP
+osmocom_fft -a hackrf -v
+.LP
+osmocom_fft -a uhd -v
+.SH "SEE ALSO"
+osmocom_siggen(1) osmocom_siggen_nogui(1) osmocom_spectrum_sense(1)
diff --git a/debian/osmocom_siggen.1 b/debian/osmocom_siggen.1
new file mode 100644
index 0000000..d9d9d47
--- /dev/null
+++ b/debian/osmocom_siggen.1
@@ -0,0 +1,222 @@
+.TH osmocom_siggen "1" "October 2013" "OSMOCOM" "User Commands"
+.SH NAME
+osmocom_siggen \- Signal Generator Application with GUI controls
+.SH SYNOPSIS
+.B osmocom_siggen:
+[\fIoptions\fR]
+.SH DESCRIPTION
+Signal Generator Application with GUI controls
+.SH OPTIONS
+.TP
+\fB\-h\fR, \fB\-\-help\fR
+show this help message and exit
+.TP
+\fB\-a\fR ARGS, \fB\-\-args\fR=\fIARGS\fR
+Device args, [default=]
+.TP
+\fB\-A\fR ANTENNA, \fB\-\-antenna\fR=\fIANTENNA\fR
+Select Rx Antenna where appropriate
+.TP
+\fB\-s\fR SAMP_RATE, \fB\-\-samp\-rate\fR=\fISAMP_RATE\fR
+Set sample rate (bandwidth), minimum by default
+.TP
+\fB\-g\fR GAIN, \fB\-\-gain\fR=\fIGAIN\fR
+Set gain in dB (default is midpoint)
+.TP
+\fB\-f\fR FREQ, \fB\-\-tx\-freq\fR=\fIFREQ\fR
+Set carrier frequency to FREQ [default=mid\-point]
+.TP
+\fB\-c\fR FREQ_CORR, \fB\-\-freq\-corr\fR=\fIFREQ_CORR\fR
+Set carrier frequency correction [default=0]
+.TP
+\fB\-x\fR WAVEFORM_FREQ, \fB\-\-waveform\-freq\fR=\fIWAVEFORM_FREQ\fR
+Set baseband waveform frequency to FREQ [default=0]
+.TP
+\fB\-y\fR WAVEFORM2_FREQ, \fB\-\-waveform2\-freq\fR=\fIWAVEFORM2_FREQ\fR
+Set 2nd waveform frequency to FREQ [default=none]
+.TP
+\fB\-\-sine\fR
+Generate a carrier modulated by a complex sine wave
+.TP
+\fB\-\-const\fR
+Generate a constant carrier
+.TP
+\fB\-\-offset\fR=\fIOFFSET\fR
+Set waveform phase offset to OFFSET [default=0]
+.TP
+\fB\-\-gaussian\fR
+Generate Gaussian random output
+.TP
+\fB\-\-uniform\fR
+Generate Uniform random output
+.TP
+\fB\-\-2tone\fR
+Generate Two Tone signal for IMD testing
+.TP
+\fB\-\-sweep\fR
+Generate a swept sine wave
+.TP
+\fB\-\-gsm\fR
+Generate GMSK modulated GSM Burst Sequence
+.TP
+\fB\-\-amplitude\fR=\fIAMPL\fR
+Set output amplitude to AMPL (0.1\-1.0) [default=0.3]
+.TP
+\fB\-v\fR, \fB\-\-verbose\fR
+Use verbose console output [default=False]
+.SH Device specification
+You can specify the source or sink device using a comma separated string of argument=value pairs. The always-up-to-date block documentation with examples is available right here.
+.SH FCD Source
+.TP
+Argument
+Notes
+.TP
+fcd=<device-index>
+0-based device identifier, optional
+.TP
+device=hw:2
+overrides the audio device
+.TP
+type=2
+selects the dongle type, 1 for Classic, 2 for Pro+
+.LP
+The "device" argument overrides the audio device used by the underlying driver to access the dongle's IQ sample stream.
+.LP
+The "type" argument selects the dongle type, 1 for Classic, 2 for Pro+.
+.SH OsmoSDR Source
+.TP
+Argument
+Notes
+.TP
+osmosdr=<device-index>
+0-based device identifier
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.TP
+buflen=<length-of-buffer>
+Default is 256kB, must be multiple of 512
+.SH RTL-SDR Source
+.TP
+Argument
+Notes
+.TP
+rtl=<device-index>
+0-based device identifier OR serial number
+.TP
+rtl_xtal=<frequency>
+Frequency (Hz) used for the RTL chip, accepts eng notation
+.TP
+tuner_xtal=<frequency>
+Frequency (Hz) used for the tuner chip, accepts eng notation
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.TP
+buflen=<length-of-buffer>
+Default is 256kB, must be multiple of 512
+.TP
+direct_samp=0|1|2
+Enable direct sampling mode on the RTL chip. 0: Disable, 1: use I channel, 2: use Q channel
+.TP
+offset_tune=0|1
+Enable offset tune mode for E4000 tuners
+.LP
+NOTE: use rtl_eeprom -s to program your own serial number to the device
+.LP
+NOTE: if you don't specify rtl_xtal/tuner_xtal, the underlying driver will use 28.0MHz
+.SH RTL-SDR TCP Source
+.TP
+Argument
+Notes
+.TP
+rtl_tcp=<hostname>:<port>
+hostname defaults to "localhost", port to "1234"
+.TP
+psize=<payload-size>
+Default is 16384 bytes
+.TP
+direct_samp=0|1|2
+Enable direct sampling mode on the RTL chip 0=Off, 1=I-ADC input enabled, 2=Q-ADC input enabled
+.TP
+offset_tune=0|1
+Enable offset tune mode for E4000 tuners 
+.SH Miri Source
+.TP
+Argument
+Notes
+.TP
+miri=<device-index>
+0-based device identifier
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.SH UHD Source / Sink
+Argument
+Notes
+.TP
+uhd
+Use this argument without a value
+.TP
+nchan=<channel-count>
+For multichannel USRP configurations use the subdev parameter to specify stream mapping
+.TP
+subdev=<subdev-spec>
+Examples: "A:0", "B:0", "A:0 B:0" when nchan=2. Refer original ettus documentation on this
+.TP
+lo_offset=<frequency>
+Offset frequency in Hz, must be within daughterboard bandwidth. Accepts eng notation
+.LP
+Additional argument/value pairs will be passed to the underlying driver, for more information see specifying the subdevice and common device identifiers in the Ettus documentation.
+.SH bladeRF Source / Sink
+.TP
+Argument
+Notes
+.TP
+bladerf[=0]
+0-based device identifier (optional)
+.TP
+fw='/path/to/the/firmware.img'
+program MCU firmware from given file. usually not needed. power cycle required.
+.TP
+fpga='/path/to/the/bitstream.rbf'
+load FPGA bitstream from given file. required only at first run at the moment.
+.SH HackRF Source / Sink
+.TP
+Argument
+Notes
+.TP
+hackrf
+Use this argument without a value
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.LP
+Only the first device found may be used at the moment because of libhackrf limitation.
+.LP
+Transmit support has been verified by using the crc-mmbTools DAB sdr transmitter.
+.SH IQ File Source
+.TP
+Argument
+Notes
+.TP
+file=<path-to-file-name>	
+.TP
+freq=<frequency>
+Center frequency in Hz, accepts eng notation
+.TP
+rate=<sampling-rate>
+Mandatory, in samples/s, accepts eng notation
+.TP
+repeat=true|false
+Default is true
+.TP
+throttle=true|false
+Throttle flow of samples, default is true
+.SH EXAMPLES
+.LP
+osmocom_siggen -a hackrf -f 100e6 --sine
+.LP
+osmocom_siggen -a hackrf -f 100e6 --sweep -x 2M -y 1 -c34
+.SH "SEE ALSO"
+osmocom_fft(1) osmocom_siggen(1) osmocom_spectrum_sense(1)
diff --git a/debian/osmocom_siggen_nogui.1 b/debian/osmocom_siggen_nogui.1
new file mode 100644
index 0000000..0228ad5
--- /dev/null
+++ b/debian/osmocom_siggen_nogui.1
@@ -0,0 +1,224 @@
+.TH osmocom_siggen_nogui "1" "October 2013" "OSMOCOM" "User Commands"
+.SH NAME
+osmocom_siggen_nogui \- Signal generator application
+.SH SYNOPSIS
+.B osmocom_siggen_nogui:
+[\fIoptions\fR]
+.SH DESCRIPTION
+Signal generator application
+.SH OPTIONS
+.TP
+\fB\-h\fR, \fB\-\-help\fR
+show this help message and exit
+.TP
+\fB\-a\fR ARGS, \fB\-\-args\fR=\fIARGS\fR
+Device args, [default=]
+.TP
+\fB\-A\fR ANTENNA, \fB\-\-antenna\fR=\fIANTENNA\fR
+Select Rx Antenna where appropriate
+.TP
+\fB\-s\fR SAMP_RATE, \fB\-\-samp\-rate\fR=\fISAMP_RATE\fR
+Set sample rate (bandwidth), minimum by default
+.TP
+\fB\-g\fR GAIN, \fB\-\-gain\fR=\fIGAIN\fR
+Set gain in dB (default is midpoint)
+.TP
+\fB\-f\fR FREQ, \fB\-\-tx\-freq\fR=\fIFREQ\fR
+Set carrier frequency to FREQ [default=mid\-point]
+.TP
+\fB\-c\fR FREQ_CORR, \fB\-\-freq\-corr\fR=\fIFREQ_CORR\fR
+Set carrier frequency correction [default=0]
+.TP
+\fB\-x\fR WAVEFORM_FREQ, \fB\-\-waveform\-freq\fR=\fIWAVEFORM_FREQ\fR
+Set baseband waveform frequency to FREQ [default=0]
+.TP
+\fB\-y\fR WAVEFORM2_FREQ, \fB\-\-waveform2\-freq\fR=\fIWAVEFORM2_FREQ\fR
+Set 2nd waveform frequency to FREQ [default=none]
+.TP
+\fB\-\-sine\fR
+Generate a carrier modulated by a complex sine wave
+.TP
+\fB\-\-const\fR
+Generate a constant carrier
+.TP
+\fB\-\-offset\fR=\fIOFFSET\fR
+Set waveform phase offset to OFFSET [default=0]
+.TP
+\fB\-\-gaussian\fR
+Generate Gaussian random output
+.TP
+\fB\-\-uniform\fR
+Generate Uniform random output
+.TP
+\fB\-\-2tone\fR
+Generate Two Tone signal for IMD testing
+.TP
+\fB\-\-sweep\fR
+Generate a swept sine wave
+.TP
+\fB\-\-gsm\fR
+Generate GMSK modulated GSM Burst Sequence
+.TP
+\fB\-\-amplitude\fR=\fIAMPL\fR
+Set output amplitude to AMPL (0.1\-1.0) [default=0.3]
+.TP
+\fB\-v\fR, \fB\-\-verbose\fR
+Use verbose console output [default=False]
+.PP
+Note: failed to enable realtime scheduling, continuing
+.SH Device specification
+You can specify the source or sink device using a comma separated string of argument=value pairs. The always-up-to-date block documentation with examples is available right here.
+.SH FCD Source
+.TP
+Argument
+Notes
+.TP
+fcd=<device-index>
+0-based device identifier, optional
+.TP
+device=hw:2
+overrides the audio device
+.TP
+type=2
+selects the dongle type, 1 for Classic, 2 for Pro+
+.LP
+The "device" argument overrides the audio device used by the underlying driver to access the dongle's IQ sample stream.
+.LP
+The "type" argument selects the dongle type, 1 for Classic, 2 for Pro+.
+.SH OsmoSDR Source
+.TP
+Argument
+Notes
+.TP
+osmosdr=<device-index>
+0-based device identifier
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.TP
+buflen=<length-of-buffer>
+Default is 256kB, must be multiple of 512
+.SH RTL-SDR Source
+.TP
+Argument
+Notes
+.TP
+rtl=<device-index>
+0-based device identifier OR serial number
+.TP
+rtl_xtal=<frequency>
+Frequency (Hz) used for the RTL chip, accepts eng notation
+.TP
+tuner_xtal=<frequency>
+Frequency (Hz) used for the tuner chip, accepts eng notation
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.TP
+buflen=<length-of-buffer>
+Default is 256kB, must be multiple of 512
+.TP
+direct_samp=0|1|2
+Enable direct sampling mode on the RTL chip. 0: Disable, 1: use I channel, 2: use Q channel
+.TP
+offset_tune=0|1
+Enable offset tune mode for E4000 tuners
+.LP
+NOTE: use rtl_eeprom -s to program your own serial number to the device
+.LP
+NOTE: if you don't specify rtl_xtal/tuner_xtal, the underlying driver will use 28.0MHz
+.SH RTL-SDR TCP Source
+.TP
+Argument
+Notes
+.TP
+rtl_tcp=<hostname>:<port>
+hostname defaults to "localhost", port to "1234"
+.TP
+psize=<payload-size>
+Default is 16384 bytes
+.TP
+direct_samp=0|1|2
+Enable direct sampling mode on the RTL chip 0=Off, 1=I-ADC input enabled, 2=Q-ADC input enabled
+.TP
+offset_tune=0|1
+Enable offset tune mode for E4000 tuners 
+.SH Miri Source
+.TP
+Argument
+Notes
+.TP
+miri=<device-index>
+0-based device identifier
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.SH UHD Source / Sink
+Argument
+Notes
+.TP
+uhd
+Use this argument without a value
+.TP
+nchan=<channel-count>
+For multichannel USRP configurations use the subdev parameter to specify stream mapping
+.TP
+subdev=<subdev-spec>
+Examples: "A:0", "B:0", "A:0 B:0" when nchan=2. Refer original ettus documentation on this
+.TP
+lo_offset=<frequency>
+Offset frequency in Hz, must be within daughterboard bandwidth. Accepts eng notation
+.LP
+Additional argument/value pairs will be passed to the underlying driver, for more information see specifying the subdevice and common device identifiers in the Ettus documentation.
+.SH bladeRF Source / Sink
+.TP
+Argument
+Notes
+.TP
+bladerf[=0]
+0-based device identifier (optional)
+.TP
+fw='/path/to/the/firmware.img'
+program MCU firmware from given file. usually not needed. power cycle required.
+.TP
+fpga='/path/to/the/bitstream.rbf'
+load FPGA bitstream from given file. required only at first run at the moment.
+.SH HackRF Source / Sink
+.TP
+Argument
+Notes
+.TP
+hackrf
+Use this argument without a value
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.LP
+Only the first device found may be used at the moment because of libhackrf limitation.
+.LP
+Transmit support has been verified by using the crc-mmbTools DAB sdr transmitter.
+.SH IQ File Source
+.TP
+Argument
+Notes
+.TP
+file=<path-to-file-name>	
+.TP
+freq=<frequency>
+Center frequency in Hz, accepts eng notation
+.TP
+rate=<sampling-rate>
+Mandatory, in samples/s, accepts eng notation
+.TP
+repeat=true|false
+Default is true
+.TP
+throttle=true|false
+Throttle flow of samples, default is true
+.SH EXAMPLES
+.LP
+osmocom_siggen_nogui -a hackrf -f 100e6 --sweep -x 2e6 -y 10 -v
+.LP
+osmocom_siggen_nogui -a uhd,subdev=A:0 -f 100e6 --sweep -x 2e6 -y 10 -s 4e6 -v
+.SH "SEE ALSO"
+osmocom_fft(1) osmocom_siggen(1) osmocom_spectrum_sense(1)
diff --git a/debian/osmocom_spectrum_sense.1 b/debian/osmocom_spectrum_sense.1
new file mode 100644
index 0000000..d10b1d4
--- /dev/null
+++ b/debian/osmocom_spectrum_sense.1
@@ -0,0 +1,196 @@
+.TH osmocom_spectrum_sense "1" "October 2013" "OSMOCOMM" "User Commands"
+.SH NAME
+osmocom_spectrum_sense \- GNU Radio application from OsmoSDR
+.SH SYNOPSIS
+.B osmocom_spectrum_sense
+[\fIoptions\fR] \fImin_freq max_freq\fR
+.SH DESCRIPTION
+GNU Radio application from OsmoSDR
+.SH OPTIONS
+.TP
+\fB\-h\fR, \fB\-\-help\fR
+show this help message and exit
+.TP
+\fB\-a\fR ARGS, \fB\-\-args\fR=\fIARGS\fR
+Device args [default=]
+.TP
+\fB\-A\fR ANTENNA, \fB\-\-antenna\fR=\fIANTENNA\fR
+Select antenna where appropriate
+.TP
+\fB\-s\fR SAMP_RATE, \fB\-\-samp\-rate\fR=\fISAMP_RATE\fR
+Set sample rate (bandwidth), minimum by default
+.TP
+\fB\-g\fR GAIN, \fB\-\-gain\fR=\fIGAIN\fR
+Set gain in dB (default is midpoint)
+.TP
+\fB\-\-tune\-delay\fR=\fISECS\fR
+Time to delay (in seconds) after changing frequency
+[default=0.25]
+.TP
+\fB\-\-dwell\-delay\fR=\fISECS\fR
+Time to dwell (in seconds) at a given frequency
+[default=0.25]
+.TP
+\fB\-b\fR Hz, \fB\-\-channel\-bandwidth\fR=\fIHz\fR
+Channel bandwidth of fft bins in Hz [default=6250.0]
+.TP
+\fB\-q\fR dB, \fB\-\-squelch\-threshold\fR=\fIdB\fR
+Squelch threshold in dB [default=none]
+.TP
+\fB\-F\fR FFT_SIZE, \fB\-\-fft\-size\fR=\fIFFT_SIZE\fR
+Specify number of FFT bins
+[default=samp_rate/channel_bw]
+.TP
+\fB\-\-real\-time\fR
+Attempt to enable real\-time scheduling
+.SH Device specification
+You can specify the source or sink device using a comma separated string of argument=value pairs. The always-up-to-date block documentation with examples is available right here.
+.SH FCD Source
+.TP
+Argument
+Notes
+.TP
+fcd=<device-index>
+0-based device identifier, optional
+.TP
+device=hw:2
+overrides the audio device
+.TP
+type=2
+selects the dongle type, 1 for Classic, 2 for Pro+
+.LP
+The "device" argument overrides the audio device used by the underlying driver to access the dongle's IQ sample stream.
+.LP
+The "type" argument selects the dongle type, 1 for Classic, 2 for Pro+.
+.SH OsmoSDR Source
+.TP
+Argument
+Notes
+.TP
+osmosdr=<device-index>
+0-based device identifier
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.TP
+buflen=<length-of-buffer>
+Default is 256kB, must be multiple of 512
+.SH RTL-SDR Source
+.TP
+Argument
+Notes
+.TP
+rtl=<device-index>
+0-based device identifier OR serial number
+.TP
+rtl_xtal=<frequency>
+Frequency (Hz) used for the RTL chip, accepts eng notation
+.TP
+tuner_xtal=<frequency>
+Frequency (Hz) used for the tuner chip, accepts eng notation
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.TP
+buflen=<length-of-buffer>
+Default is 256kB, must be multiple of 512
+.TP
+direct_samp=0|1|2
+Enable direct sampling mode on the RTL chip. 0: Disable, 1: use I channel, 2: use Q channel
+.TP
+offset_tune=0|1
+Enable offset tune mode for E4000 tuners
+.LP
+NOTE: use rtl_eeprom -s to program your own serial number to the device
+.LP
+NOTE: if you don't specify rtl_xtal/tuner_xtal, the underlying driver will use 28.0MHz
+.SH RTL-SDR TCP Source
+.TP
+Argument
+Notes
+.TP
+rtl_tcp=<hostname>:<port>
+hostname defaults to "localhost", port to "1234"
+.TP
+psize=<payload-size>
+Default is 16384 bytes
+.TP
+direct_samp=0|1|2
+Enable direct sampling mode on the RTL chip 0=Off, 1=I-ADC input enabled, 2=Q-ADC input enabled
+.TP
+offset_tune=0|1
+Enable offset tune mode for E4000 tuners 
+.SH Miri Source
+.TP
+Argument
+Notes
+.TP
+miri=<device-index>
+0-based device identifier
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.SH UHD Source / Sink
+Argument
+Notes
+.TP
+uhd
+Use this argument without a value
+.TP
+nchan=<channel-count>
+For multichannel USRP configurations use the subdev parameter to specify stream mapping
+.TP
+subdev=<subdev-spec>
+Examples: "A:0", "B:0", "A:0 B:0" when nchan=2. Refer original ettus documentation on this
+.TP
+lo_offset=<frequency>
+Offset frequency in Hz, must be within daughterboard bandwidth. Accepts eng notation
+.LP
+Additional argument/value pairs will be passed to the underlying driver, for more information see specifying the subdevice and common device identifiers in the Ettus documentation.
+.SH bladeRF Source / Sink
+.TP
+Argument
+Notes
+.TP
+bladerf[=0]
+0-based device identifier (optional)
+.TP
+fw='/path/to/the/firmware.img'
+program MCU firmware from given file. usually not needed. power cycle required.
+.TP
+fpga='/path/to/the/bitstream.rbf'
+load FPGA bitstream from given file. required only at first run at the moment.
+.SH HackRF Source / Sink
+.TP
+Argument
+Notes
+.TP
+hackrf
+Use this argument without a value
+.TP
+buffers=<number-of-buffers>
+Default is 32
+.LP
+Only the first device found may be used at the moment because of libhackrf limitation.
+.LP
+Transmit support has been verified by using the crc-mmbTools DAB sdr transmitter.
+.SH IQ File Source
+.TP
+Argument
+Notes
+.TP
+file=<path-to-file-name>	
+.TP
+freq=<frequency>
+Center frequency in Hz, accepts eng notation
+.TP
+rate=<sampling-rate>
+Mandatory, in samples/s, accepts eng notation
+.TP
+repeat=true|false
+Default is true
+.TP
+throttle=true|false
+Throttle flow of samples, default is true
+.SH "SEE ALSO"
+osmocom_fft(1) osmocom_siggen(1) osmocom_siggen_nogui(1)
diff --git a/debian/rules b/debian/rules
new file mode 100755
index 0000000..a939fc2
--- /dev/null
+++ b/debian/rules
@@ -0,0 +1,29 @@
+#!/usr/bin/make -f
+DEB_HOST_MULTIARCH ?= $(shell dpkg-architecture -qDEB_HOST_MULTIARCH)
+export DEB_HOST_MULTIARCH
+DEB_DEBIAN_DIR=$(dir $(firstword $(MAKEFILE_LIST)))
+VER=$(shell dpkg-parsechangelog -l$(DEB_DEBIAN_DIR)/changelog \
+              | sed -rne 's,^Version: ([^-]+).*,\1,p')
+GITREV=$(shell echo $(VER) | sed -rne 's,[0-9]+\.[0-9]+\.[0-9]+\.[0-9]+\.([0-f]+),\1,p')
+
+%:
+	dh $@ --with python2
+
+override_dh_auto_configure:
+	dh_auto_configure -- -DLIB_SUFFIX="/$(DEB_HOST_MULTIARCH)" -DPythonLibs_FIND_VERSION:STRING="2.7" -DPYTHON_EXECUTABLE:STRING="/usr/bin/python"
+
+override_dh_auto_install:
+	dh_auto_install
+	rm -f debian/gr-osmosdr/usr/lib/python2.7/dist-packages/osmosdr/*pyc
+	rm -f debian/gr-osmosdr/usr/lib/python2.7/dist-packages/osmosdr/*pyo
+
+override_dh_makeshlibs:
+	dh_makeshlibs -V 'libgnuradio-osmosdr0.1.4 (>= 0.1.4-13)'
+
+version-to-get:
+	echo $(VER) is $(GITREV)
+
+get-orig-source: version-to-get
+	git clone git://git.osmocom.org/gr-osmosdr
+	cd gr-osmosdr && git archive --format=tar --prefix=gr-osmosdr-$(VER)/  $(GITREV) | xz > ../gr-osmosdr_$(VER).orig.tar.xz
+	rm -rf gr-osmosdr
diff --git a/debian/source/format b/debian/source/format
new file mode 100644
index 0000000..89ae9db
--- /dev/null
+++ b/debian/source/format
@@ -0,0 +1 @@
+3.0 (native)
diff --git a/debian/watch b/debian/watch
new file mode 100644
index 0000000..879e5c7
--- /dev/null
+++ b/debian/watch
@@ -0,0 +1,3 @@
+version=3
+opts="downloadurlmangle=s/refs\/tags/snapshot/,uversionmangle=s|(.*)git|1|" \
+ http://cgit.osmocom.org/gr-osmosdr/refs/tags /gr-osmosdr/snapshot/gr-osmosdr-(\d.*)\.tar\.xz