1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
|
/**
* \file
*
* \brief SD/MMC stack configuration file.
*
* Copyright (c) 2015 Atmel Corporation. All rights reserved.
*
* \asf_license_start
*
* \page License
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* 3. The name of Atmel may not be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* 4. This software may only be redistributed and used in connection with an
* Atmel microcontroller product.
*
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
* \asf_license_stop
*
*/
/*
* Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
*/
#ifndef CONF_SD_MMC_H_INCLUDED
#define CONF_SD_MMC_H_INCLUDED
// Define to enable the SPI mode instead of Multimedia Card interface mode
#define SD_MMC_SPI_MODE
// Define to enable the SDIO support
//#define SDIO_SUPPORT_ENABLE
// Define to enable the debug trace to the current standard output (stdio)
//#define SD_MMC_DEBUG
// Define to memory count
#define SD_MMC_SPI_MEM_CNT 1
//! Select the SPI module SD/MMC is connected to
#define SD_MMC_SPI EXT1_SPI_MODULE
#define SD_MMC_SPI_PINMUX_SETTING EXT1_SPI_SERCOM_MUX_SETTING
#define SD_MMC_SPI_PINMUX_PAD0 EXT1_SPI_SERCOM_PINMUX_PAD0
#define SD_MMC_SPI_PINMUX_PAD1 EXT1_SPI_SERCOM_PINMUX_PAD1
#define SD_MMC_SPI_PINMUX_PAD2 EXT1_SPI_SERCOM_PINMUX_PAD2
#define SD_MMC_SPI_PINMUX_PAD3 EXT1_SPI_SERCOM_PINMUX_PAD3
#define SD_MMC_CS EXT1_PIN_15
#define SD_MMC_0_CD_GPIO (EXT1_PIN_10)
#define SD_MMC_0_CD_DETECT_VALUE 0
// Define the SPI clock source
#define SD_MMC_SPI_SOURCE_CLOCK GCLK_GENERATOR_0
// Define the SPI max clock
#define SD_MMC_SPI_MAX_CLOCK 10000000
#endif /* CONF_SD_MMC_H_INCLUDED */
|
