path: root/docbook/wsug_src/WSUG_app_tools.xml

<!-- WSUG Appendix Tools -->
<!-- $Id$ -->

<appendix id="AppTools">
  <title>Related command line tools</title>

  <section id="AppToolsIntroduction">
    <title>Introduction</title>
    <para>
    Besides the Wireshark GUI application, there are some command line tools
    which can be helpful for doing some more specialized things. These tools
    will be described in this chapter.
    </para>
  </section>

  <section id="AppToolstshark">
    <title><command>tshark</command>: Terminal-based Wireshark</title>
    <para>
      <application>TShark</application> is a terminal oriented version
      of Wireshark designed for capturing and displaying packets when an
      interactive user interface isn't necessary or available. It supports
      the same options as <command>wireshark</command>. For more
      information on <command>tshark</command>, see the manual pages
      (<command>man tshark</command>).
    </para>
    <para>
    <example id="AppToolstsharkEx">
      <title>Help information available from tshark</title>
      <programlisting>
TShark 1.11.0 (SVN Rev 52564 from /trunk)
Dump and analyze network traffic.
See http://www.wireshark.org for more information.

Copyright 1998-2013 Gerald Combs &lt;gerald@wireshark.org&gt; and contributors.
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

Usage: tshark [options] ...

Capture interface:
  -i &lt;interface&gt;           name or idx of interface (def: first non-loopback)
  -f &lt;capture filter&gt;      packet filter in libpcap filter syntax
  -s &lt;snaplen&gt;             packet snapshot length (def: 65535)
  -p                       don't capture in promiscuous mode
  -I                       capture in monitor mode, if available
  -B &lt;buffer size&gt;         size of kernel buffer (def: 1MB)
  -y &lt;link type&gt;           link layer type (def: first appropriate)
  -D                       print list of interfaces and exit
  -L                       print list of link-layer types of iface and exit

Capture stop conditions:
  -c &lt;packet count&gt;        stop after n packets (def: infinite)
  -a &lt;autostop cond.&gt; ...  duration:NUM - stop after NUM seconds
                           filesize:NUM - stop this file after NUM KB
                              files:NUM - stop after NUM files
Capture output:
  -b &lt;ringbuffer opt.&gt; ... duration:NUM - switch to next file after NUM secs
                           filesize:NUM - switch to next file after NUM KB
                              files:NUM - ringbuffer: replace after NUM files
RPCAP options:
  -A &lt;user&gt;:&lt;password&gt;     use RPCAP password authentication
Input file:
  -r &lt;infile&gt;              set the filename to read from (no pipes or stdin!)

Processing:
  -2                       perform a two-pass analysis
  -R &lt;read filter&gt;         packet Read filter in Wireshark display filter syntax
  -Y &lt;display filter&gt;      packet displaY filter in Wireshark display filter syntax
  -n                       disable all name resolutions (def: all enabled)
  -N &lt;name resolve flags&gt;  enable specific name resolution(s): "mntC"
  -d &lt;layer_type&gt;==&lt;selector&gt;,&lt;decode_as_protocol&gt; ...
                           "Decode As", see the man page for details
                           Example: tcp.port==8888,http
  -H &lt;hosts file&gt;          read a list of entries from a hosts file, which will
                           then be written to a capture file. (Implies -W n)
Output:
  -w &lt;outfile|-&gt;           write packets to a pcap-format file named "outfile"
                           (or to the standard output for "-")
  -C &lt;config profile&gt;      start with specified configuration profile
  -F &lt;output file type&gt;    set the output file type, default is libpcap
                           an empty "-F" option will list the file types
  -V                       add output of packet tree        (Packet Details)
  -O &lt;protocols&gt;           Only show packet details of these protocols, comma
                           separated
  -P                       print packet summary even when writing to a file
  -S &lt;separator&gt;           the line separator to print between packets
  -x                       add output of hex and ASCII dump (Packet Bytes)
  -T pdml|ps|psml|text|fields
                           format of text output (def: text)
  -e &lt;field&gt;               field to print if -Tfields selected (e.g. tcp.port, _ws.col.Info);
                           this option can be repeated to print multiple fields
  -E&lt;fieldsoption&gt;=&lt;value&gt; set options for output when -Tfields selected:
     header=y|n            switch headers on and off
     separator=/t|/s|&lt;char&gt; select tab, space, printable character as separator
     occurrence=f|l|a      print first, last or all occurrences of each field
     aggregator=,|/s|&lt;char&gt; select comma, space, printable character as
                           aggregator
     quote=d|s|n           select double, single, no quotes for values
  -t a|ad|d|dd|e|r|u|ud    output format of time stamps (def: r: rel. to first)
  -u s|hms                 output format of seconds (def: s: seconds)
  -l                       flush standard output after each packet
  -q                       be more quiet on stdout (e.g. when using statistics)
  -Q                       only log true errors to stderr (quieter than -q)
  -g                       enable group read access on the output file(s)
  -W n                     Save extra information in the file, if supported.
                           n = write network address resolution information
  -X &lt;key&gt;:&lt;value&gt;         eXtension options, see the man page for details
  -z &lt;statistics&gt;          various statistics, see the man page for details
  --capture-comment &lt;comment&gt;
                           add a capture comment to the newly created
                           output file (only for pcapng)

Miscellaneous:
  -h                       display this help and exit
  -v                       display version info and exit
  -o &lt;name&gt;:&lt;value&gt; ...    override preference setting
  -K &lt;keytab&gt;              keytab file to use for kerberos decryption
  -G [report]              dump one of several available reports and exit
                           default report="fields"
                           use "-G ?" for more help
      </programlisting>
    </example>
    </para>
  </section>

  <section id="AppToolstcpdump">
    <title><command>tcpdump</command>: Capturing with tcpdump for viewing
    with Wireshark</title>
    <para>
      There are occasions when you want to capture packets using
      <command>tcpdump</command> rather than <command>wireshark</command>,
      especially when you want to do a remote capture and do not want the
      network load associated with running Wireshark remotely (not to
      mention all the X traffic polluting your capture).
    </para>
    <para>
      However, the default <command>tcpdump</command> parameters result in a
      capture file where each packet is truncated, because most versions of
      <command>tcpdump</command>, will, by default, only capture the first
      68 or 96 bytes of each packet.
    </para>
    <para>
      To ensure that you capture complete packets, use the following command:
      <programlisting>
tcpdump -i &lt;interface> -s 65535 -w &lt;some-file>
      </programlisting>
      You will have to specify the correct <command>interface</command> and
      the name of a <command>file</command> to save into. In addition,
      you will have to terminate the capture with ^C when you believe you
      have captured enough packets.
    </para>
    <note><title>Note!</title>
    <para>
    tcpdump is not part of the Wireshark distribution. You can get it from:
    <ulink url="&TcpdumpWebsite;">&TcpdumpWebsite;</ulink> for various
    platforms.
    </para>
    </note>
  </section>

  <section id="AppToolsdumpcap">
    <title><command>dumpcap</command>: Capturing with dumpcap for viewing
    with Wireshark</title>
    <para>
    <application>Dumpcap</application> is a network traffic dump tool.
    It captures packet data from a live network and writes the
    packets to a file.
    Dumpcap's native capture file format is libpcap format, which is also
    the format used by Wireshark, tcpdump and various other tools.
    </para>
    <para>
    Without any options set it will use the pcap library to capture traffic
    from the first available network interface and write the received raw
    packet data, along with the packets' time stamps into a libpcap file.
    </para>
    <para>
    Packet capturing is performed with the pcap library.
    The capture filter syntax follows the rules of the pcap library.
    </para>
    <para>
    <example id="AppToolsdumpcapEx">
      <title>Help information available from dumpcap</title>
      <programlisting>
Dumpcap 1.11.0 (SVN Rev 52564 from /trunk)
Capture network packets and dump them into a pcapng file.
See http://www.wireshark.org for more information.

Usage: dumpcap [options] ...

Capture interface:
  -i &lt;interface&gt;           name or idx of interface (def: first non-loopback)
                           or for remote capturing, use one of these formats:
                               rpcap://&lt;host&gt;/&lt;interface&gt;
                               TCP@&lt;host&gt;:&lt;port&gt;
  -f &lt;capture filter&gt;      packet filter in libpcap filter syntax
  -s &lt;snaplen&gt;             packet snapshot length (def: 65535)
  -p                       don't capture in promiscuous mode
  -I                       capture in monitor mode, if available
  -B &lt;buffer size&gt;         size of kernel buffer in MB (def: 2MB)
  -y &lt;link type&gt;           link layer type (def: first appropriate)
  -D                       print list of interfaces and exit
  -L                       print list of link-layer types of iface and exit
  -d                       print generated BPF code for capture filter
  -k                       set channel on wifi interface &lt;freq&gt;,[&lt;type&gt;]
  -S                       print statistics for each interface once per second
  -M                       for -D, -L, and -S, produce machine-readable output

RPCAP options:
  -r                       don't ignore own RPCAP traffic in capture
  -u                       use UDP for RPCAP data transfer
  -A &lt;user&gt;:&lt;password&gt;     use RPCAP password authentication
  -m &lt;sampling type&gt;       use packet sampling
                           count:NUM - capture one packet of every NUM
                           timer:NUM - capture no more than 1 packet in NUM ms
Stop conditions:
  -c &lt;packet count&gt;        stop after n packets (def: infinite)
  -a &lt;autostop cond.&gt; ...  duration:NUM - stop after NUM seconds
                           filesize:NUM - stop this file after NUM KB
                              files:NUM - stop after NUM files
Output (files):
  -w &lt;filename&gt;            name of file to save (def: tempfile)
  -g                       enable group read access on the output file(s)
  -b &lt;ringbuffer opt.&gt; ... duration:NUM - switch to next file after NUM secs
                           filesize:NUM - switch to next file after NUM KB
                              files:NUM - ringbuffer: replace after NUM files
  -n                       use pcapng format instead of pcap (default)
  -P                       use libpcap format instead of pcapng
  --capture-comment &lt;comment&gt;
                           add a capture comment to the output file
                           (only for pcapng)

Miscellaneous:
  -N &lt;packet_limit&gt;        maximum number of packets buffered within dumpcap
  -C &lt;byte_limit&gt;          maximum number of bytes used for buffering packets
                           within dumpcap
  -t                       use a separate thread per interface
  -q                       don't report packet capture counts
  -v                       print version information and exit
  -h                       display this help and exit

Example: dumpcap -i eth0 -a duration:60 -w output.pcapng
"Capture packets from interface eth0 until 60s passed into output.pcapng"

Use Ctrl-C to stop capturing at any time.
      </programlisting>
    </example>
    </para>
  </section>

  <section id="AppToolscapinfos">
    <title><command>capinfos</command>: Print information about capture files
    </title>
    <para>
      Included with Wireshark is a small utility called
      <command>capinfos</command>, which is a command-line utility to
      print information about binary capture files.
    </para>
    <para>
    <example id="AppToolscapinfosEx">
      <title>Help information available from capinfos</title>
      <programlisting>
Capinfos 1.11.0 (SVN Rev 52564 from /trunk)
Prints various information (infos) about capture files.
See http://www.wireshark.org for more information.

Usage: capinfos [options] &lt;infile&gt; ...

General infos:
  -t display the capture file type
  -E display the capture file encapsulation
  -H display the SHA1, RMD160, and MD5 hashes of the file
  -k display the capture comment

Size infos:
  -c display the number of packets
  -s display the size of the file (in bytes)
  -d display the total length of all packets (in bytes)
  -l display the packet size limit (snapshot length)

Time infos:
  -u display the capture duration (in seconds)
  -a display the capture start time
  -e display the capture end time
  -o display the capture file chronological status (True/False)
  -S display start and end times as seconds

Statistic infos:
  -y display average data rate (in bytes/sec)
  -i display average data rate (in bits/sec)
  -z display average packet size (in bytes)
  -x display average packet rate (in packets/sec)

Output format:
  -L generate long report (default)
  -T generate table report
  -M display machine-readable values in long reports

Table report options:
  -R generate header record (default)
  -r do not generate header record

  -B separate infos with TAB character (default)
  -m separate infos with comma (,) character
  -b separate infos with SPACE character

  -N do not quote infos (default)
  -q quote infos with single quotes (')
  -Q quote infos with double quotes (")

Miscellaneous:
  -h display this help and exit
  -C cancel processing if file open fails (default is to continue)
  -A generate all infos (default)

Options are processed from left to right order with later options superceding
or adding to earlier options.

If no options are given the default is to display all infos in long report
output format.
      </programlisting>
    </example>
    </para>
  </section>

  <section id="AppToolsrawshark" >
    <title><command>rawshark</command>: Dump and analyze network traffic.
    </title>
    <para>
      Rawshark reads a stream of packets from a file or pipe, and prints
      a line describing its output, followed by a set of matching fields
      for each packet on stdout.
    </para>
    <example id="AppToolsrawsharkEx">
      <title>Help information available from rawshark</title>
      <programlisting>
Rawshark 1.11.0 (SVN Rev 52564 from /trunk)
Dump and analyze network traffic.
See http://www.wireshark.org for more information.

Copyright 1998-2013 Gerald Combs &lt;gerald@wireshark.org&gt; and contributors.
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

Usage: rawshark [options] ...

Input file:
  -r &lt;infile&gt;              set the pipe or file name to read from

Processing:
  -d &lt;encap:linktype&gt;|&lt;proto:protoname&gt;
                           packet encapsulation or protocol
  -F &lt;field&gt;               field to display
  -n                       disable all name resolution (def: all enabled)
  -N &lt;name resolve flags&gt;  enable specific name resolution(s): "mntC"
  -p                       use the system's packet header format
                           (which may have 64-bit timestamps)
  -R &lt;read filter&gt;         packet filter in Wireshark display filter syntax
  -s                       skip PCAP header on input

Output:
  -l                       flush output after each packet
  -S                       format string for fields
                           (%D - name, %S - stringval, %N numval)
  -t ad|a|r|d|dd|e         output format of time stamps (def: r: rel. to first)

Miscellaneous:
  -h                       display this help and exit
  -o &lt;name&gt;:&lt;value&gt; ...    override preference setting
  -v                       display version info and exit
      </programlisting>
    </example>
  </section>

  <section id="AppToolseditcap">
    <title><command>editcap</command>: Edit capture files</title>
    <para>
      Included with Wireshark is a small utility called
      <command>editcap</command>, which is a command-line utility for
      working with capture files.  Its main function is to remove
      packets from capture files, but it can also be used to convert
      capture files from one format to another, as well as to print
      information about capture files.
    </para>
    <para>

    <example id="AppToolseditcapEx">
      <title>Help information available from editcap</title>
      <para>
      <programlisting>
Editcap 1.11.0 (SVN Rev 52564 from /trunk)
Edit and/or translate the format of capture files.
See http://www.wireshark.org for more information.

Usage: editcap [options] ... &lt;infile&gt; &lt;outfile&gt; [ &lt;packet#&gt;[-&lt;packet#&gt;] ... ]

&lt;infile&gt; and &lt;outfile&gt; must both be present.
A single packet or a range of packets can be selected.

Packet selection:
  -r                     keep the selected packets; default is to delete them.
  -A &lt;start time&gt;        only output packets whose timestamp is after (or equal
                         to) the given time (format as YYYY-MM-DD hh:mm:ss).
  -B &lt;stop time&gt;         only output packets whose timestamp is before the
                         given time (format as YYYY-MM-DD hh:mm:ss).

Duplicate packet removal:
  -d                     remove packet if duplicate (window == 5).
  -D &lt;dup window&gt;        remove packet if duplicate; configurable &lt;dup window&gt;
                         Valid &lt;dup window&gt; values are 0 to 1000000.
                         NOTE: A &lt;dup window&gt; of 0 with -v (verbose option) is
                         useful to print MD5 hashes.
  -w &lt;dup time window&gt;   remove packet if duplicate packet is found EQUAL TO OR
                         LESS THAN &lt;dup time window&gt; prior to current packet.
                         A &lt;dup time window&gt; is specified in relative seconds
                         (e.g. 0.000001).

           NOTE: The use of the 'Duplicate packet removal' options with
           other editcap options except -v may not always work as expected.
           Specifically the -r, -t or -S options will very likely NOT have the
           desired effect if combined with the -d, -D or -w.

Packet manipulation:
  -s &lt;snaplen&gt;           truncate each packet to max. &lt;snaplen&gt; bytes of data.
  -C [offset:]&lt;choplen&gt;  chop each packet by &lt;choplen&gt; bytes. Positive values
                         chop at the packet beginning, negative values at the
                         packet end. If an optional offset precedes the length,
                         then the bytes chopped will be offset from that value.
                         Positive offsets are from the packet beginning,
                         negative offsets are from the packet end. You can use
                         this option more than once, allowing up to 2 chopping
                         regions within a packet provided that at least 1
                         choplen is positive and at least 1 is negative.
  -L                     adjust the frame length when chopping and/or snapping
  -t &lt;time adjustment&gt;   adjust the timestamp of each packet;
                         &lt;time adjustment&gt; is in relative seconds (e.g. -0.5).
  -S &lt;strict adjustment&gt; adjust timestamp of packets if necessary to insure
                         strict chronological increasing order. The &lt;strict
                         adjustment&gt; is specified in relative seconds with
                         values of 0 or 0.000001 being the most reasonable.
                         A negative adjustment value will modify timestamps so
                         that each packet's delta time is the absolute value
                         of the adjustment specified. A value of -0 will set
                         all packets to the timestamp of the first packet.
  -E &lt;error probability&gt; set the probability (between 0.0 and 1.0 incl.) that
                         a particular packet byte will be randomly changed.

Output File(s):
  -c &lt;packets per file&gt;  split the packet output to different files based on
                         uniform packet counts with a maximum of
                         &lt;packets per file&gt; each.
  -i &lt;seconds per file&gt;  split the packet output to different files based on
                         uniform time intervals with a maximum of
                         &lt;seconds per file&gt; each.
  -F &lt;capture type&gt;      set the output file type; default is pcapng. An empty
                         "-F" option will list the file types.
  -T &lt;encap type&gt;        set the output file encapsulation type; default is the
                         same as the input file. An empty "-T" option will
                         list the encapsulation types.

Miscellaneous:
  -h                     display this help and exit.
  -v                     verbose output.
                         If -v is used with any of the 'Duplicate Packet
                         Removal' options (-d, -D or -w) then Packet lengths
                         and MD5 hashes are printed to standard-out.
      </programlisting>
      </para>
    </example>
    <example id="AppToolseditcapEx1">
      <title>Capture file types available from editcap</title>
      <para>
      <programlisting>
$ editcap -F
editcap: option requires an argument -- 'F'
editcap: The available capture file types for the "-F" flag are:
    5views - InfoVista 5View capture
    btsnoop - Symbian OS btsnoop
    commview - TamoSoft CommView
    dct2000 - Catapult DCT2000 trace (.out format)
    erf - Endace ERF capture
    eyesdn - EyeSDN USB S0/E1 ISDN trace format
    k12text - K12 text file
    lanalyzer - Novell LANalyzer
    modlibpcap - Modified tcpdump - libpcap
    netmon1 - Microsoft NetMon 1.x
    netmon2 - Microsoft NetMon 2.x
    nettl - HP-UX nettl trace
    ngsniffer - Sniffer (DOS)
    ngwsniffer_1_1 - NetXray, Sniffer (Windows) 1.1
    ngwsniffer_2_0 - Sniffer (Windows) 2.00x
    niobserver - Network Instruments Observer
    nokialibpcap - Nokia tcpdump - libpcap 
    nseclibpcap - Wireshark - nanosecond libpcap
    nstrace10 - NetScaler Trace (Version 1.0)
    nstrace20 - NetScaler Trace (Version 2.0)
    pcap - Wireshark/tcpdump/... - pcap
    pcapng - Wireshark/... - pcapng
    rf5 - Tektronix K12xx 32-bit .rf5 format
    rh6_1libpcap - RedHat 6.1 tcpdump - libpcap
    snoop - Sun snoop
    suse6_3libpcap - SuSE 6.3 tcpdump - libpcap
    visual - Visual Networks traffic capture
      </programlisting>
      </para>
    </example>
    <example id="AppToolseditcapEx2">
      <title>Encapsulation types available from editcap</title>
      <para></para>
    </example>
    <!-- This kludge is needed since example doesn't break across PDF pages -->
    <informalexample>
      <para>
      <programlisting>
$ editcap -T
editcap: option requires an argument -- 'T'
editcap: The available encapsulation types for the "-T" flag are:
    ap1394 - Apple IP-over-IEEE 1394
    arcnet - ARCNET
    arcnet_linux - Linux ARCNET
    ascend - Lucent/Ascend access equipment
    atm-pdus - ATM PDUs
    atm-pdus-untruncated - ATM PDUs - untruncated
    atm-rfc1483 - RFC 1483 ATM
    ax25 - Amateur Radio AX.25
    ax25-kiss - AX.25 with KISS header
    bacnet-ms-tp - BACnet MS/TP
    bacnet-ms-tp-with-direction - BACnet MS/TP with Directional Info
    ber - ASN.1 Basic Encoding Rules
    bluetooth-h4 - Bluetooth H4
    bluetooth-h4-linux - Bluetooth H4 with linux header
    bluetooth-hci - Bluetooth without transport layer
    bluetooth-le-ll - Bluetooth Low Energy Link Layer
    can20b - Controller Area Network 2.0B
    chdlc - Cisco HDLC
    chdlc-with-direction - Cisco HDLC with Directional Info
    cosine - CoSine L2 debug log
    dbus - D-Bus
    dct2000 - Catapult DCT2000
    docsis - Data Over Cable Service Interface Specification
    dpnss_link - Digital Private Signalling System No 1 Link Layer
    dvbci - DVB-CI (Common Interface)
    enc - OpenBSD enc(4) encapsulating interface
    erf - Extensible Record Format
    ether - Ethernet
    ether-nettl - Ethernet with nettl headers
    fc2 - Fibre Channel FC-2
    fc2sof - Fibre Channel FC-2 With Frame Delimiter
    fddi - FDDI
    fddi-nettl - FDDI with nettl headers
    fddi-swapped - FDDI with bit-swapped MAC addresses
    flexray - FlexRay
    frelay - Frame Relay
    frelay-with-direction - Frame Relay with Directional Info
    gcom-serial - GCOM Serial
    gcom-tie1 - GCOM TIE1
    gprs-llc - GPRS LLC
    gsm_um - GSM Um Interface
    hhdlc - HiPath HDLC
    i2c - I2C
    ieee-802-11 - IEEE 802.11 Wireless LAN
    ieee-802-11-airopeek - IEEE 802.11 plus AiroPeek radio header
    ieee-802-11-avs - IEEE 802.11 plus AVS radio header
    ieee-802-11-netmon - IEEE 802.11 plus Network Monitor radio header
    ieee-802-11-prism - IEEE 802.11 plus Prism II monitor mode radio header
    ieee-802-11-radio - IEEE 802.11 Wireless LAN with radio information
    ieee-802-11-radiotap - IEEE 802.11 plus radiotap radio header
    ieee-802-16-mac-cps - IEEE 802.16 MAC Common Part Sublayer
    infiniband - InfiniBand
    ios - Cisco IOS internal
    ip-over-fc - RFC 2625 IP-over-Fibre Channel
    ip-over-ib - IP over Infiniband
    ipfix - IPFIX
    ipmb - Intelligent Platform Management Bus
    ipnet - Solaris IPNET
    irda - IrDA
    isdn - ISDN
    ixveriwave - IxVeriWave header and stats block
    jfif - JPEG/JFIF
    juniper-atm1 - Juniper ATM1
    juniper-atm2 - Juniper ATM2
    juniper-chdlc - Juniper C-HDLC
    juniper-ether - Juniper Ethernet
    juniper-frelay - Juniper Frame-Relay
    juniper-ggsn - Juniper GGSN
    juniper-mlfr - Juniper MLFR
    juniper-mlppp - Juniper MLPPP
    juniper-ppp - Juniper PPP
    juniper-pppoe - Juniper PPPoE
    juniper-svcs - Juniper Services
    juniper-vp - Juniper Voice PIC
    k12 - K12 protocol analyzer
    lapb - LAPB
    lapd - LAPD
    layer1-event - EyeSDN Layer 1 event
    lin - Local Interconnect Network
    linux-atm-clip - Linux ATM CLIP
    linux-lapd - LAPD with Linux pseudo-header
    linux-sll - Linux cooked-mode capture
    ltalk - Localtalk
    mime - MIME
    most - Media Oriented Systems Transport
    mp2ts - ISO/IEC 13818-1 MPEG2-TS
    mpeg - MPEG
    mtp2 - SS7 MTP2
    mtp2-with-phdr - MTP2 with pseudoheader
    mtp3 - SS7 MTP3
    mux27010 - MUX27010
    netanalyzer - netANALYZER
    netanalyzer-transparent - netANALYZER-Transparent
    nfc-llcp - NFC LLCP
    nflog - NFLOG
    nstrace10 - NetScaler Encapsulation 1.0 of Ethernet
    nstrace20 - NetScaler Encapsulation 2.0 of Ethernet
    null - NULL
    packetlogger - PacketLogger
    pflog - OpenBSD PF Firewall logs
    pflog-old - OpenBSD PF Firewall logs, pre-3.4
    ppi - Per-Packet Information header
    ppp - PPP
    ppp-with-direction - PPP with Directional Info
    pppoes - PPP-over-Ethernet session
    raw-icmp-nettl - Raw ICMP with nettl headers
    raw-icmpv6-nettl - Raw ICMPv6 with nettl headers
    raw-telnet-nettl - Raw telnet with nettl headers
    rawip - Raw IP
    rawip-nettl - Raw IP with nettl headers
    rawip4 - Raw IPv4
    rawip6 - Raw IPv6
    redback - Redback SmartEdge
    rtac-serial - RTAC serial-line
    sccp - SS7 SCCP
    sctp - SCTP
    sdh - SDH
    sdlc - SDLC
    sita-wan - SITA WAN packets
    slip - SLIP
    socketcan - SocketCAN
    symantec - Symantec Enterprise Firewall
    tnef - Transport-Neutral Encapsulation Format
    tr - Token Ring
    tr-nettl - Token Ring with nettl headers
    tzsp - Tazmen sniffer protocol
    unknown - Unknown
    unknown-nettl - Unknown link-layer type with nettl headers
    usb - Raw USB packets
    usb-linux - USB packets with Linux header
    usb-linux-mmap - USB packets with Linux header and padding
    usb-usbpcap - USB packets with USBPcap header
    user0 - USER 0
    user1 - USER 1
    user2 - USER 2
    user3 - USER 3
    user4 - USER 4
    user5 - USER 5
    user6 - USER 6
    user7 - USER 7
    user8 - USER 8
    user9 - USER 9
    user10 - USER 10
    user11 - USER 11
    user12 - USER 12
    user13 - USER 13
    user14 - USER 14
    user15 - USER 15
    v5-ef - V5 Envelope Function
    whdlc - Wellfleet HDLC
    wireshark-upper-pdu - Wireshark Upper PDU export
    wpan - IEEE 802.15.4 Wireless PAN
    wpan-nofcs - IEEE 802.15.4 Wireless PAN with FCS not present
    wpan-nonask-phy - IEEE 802.15.4 Wireless PAN non-ASK PHY
    x2e-serial - X2E serial line capture
    x2e-xoraya - X2E Xoraya
      </programlisting>
      </para>
    </informalexample>
    </para>
  </section>

  <section id="AppToolsmergecap">
    <title><command>mergecap</command>:
      Merging multiple capture files into one
    </title>
    <para>
      Mergecap is a program that combines multiple saved capture files
      into a single output file specified by the -w argument.  Mergecap
      knows how to read libpcap capture files, including those of tcpdump.
      In addition, Mergecap can read capture files from snoop (including
      Shomiti) and atmsnoop, LanAlyzer, Sniffer (compressed or
      uncompressed), Microsoft Network Monitor, AIX's iptrace, NetXray,
      Sniffer Pro, RADCOM's WAN/LAN analyzer, Lucent/Ascend router debug
      output, HP-UX's nettl, and the dump output from Toshiba's ISDN
      routers.  There is no need to tell Mergecap what type of file you are
      reading; it will determine the file type by itself.  Mergecap is also
      capable of reading any of these file formats if they are compressed
      using gzip.  Mergecap recognizes this directly from the file; the '.gz'
      extension is not required for this purpose.
    </para>
    <para>
      By default, it writes the capture file in libpcap format, and writes
      all of the packets in the input capture files to the output file.
      The -F flag can be used to specify the format in which to write the
      capture file; it can write the file in libpcap format (standard
      libpcap format, a modified format used by some patched versions of
      libpcap, the format used by Red Hat Linux 6.1, or the format used
      by SuSE Linux 6.3), snoop format, uncompressed Sniffer format,
      Microsoft Network Monitor 1.x format, and the format used by
      Windows-based versions of the Sniffer software.
    </para>
    <para>
      Packets from the input files are merged in chronological order based
      on each frame's timestamp, unless the -a flag is specified.  Mergecap
      assumes that frames within a single capture file are already stored
      in chronological order.  When the -a flag is specified, packets are
      copied directly from each input file to the output file, independent
      of each frame's timestamp.
    </para>
    <para>
      If the -s flag is used to specify a snapshot length, frames in the
      input file with more captured data than the specified snapshot length
      will have only the amount of data specified by the snapshot length
      written to the output file.  This may be useful if the program that
      is to read the output file cannot handle packets larger than a
      certain size (for example, the versions of snoop in Solaris 2.5.1 and
      Solaris 2.6 appear to reject Ethernet frames larger than the standard
      Ethernet MTU, making them incapable of handling gigabit Ethernet
      captures if jumbo frames were used).
    </para>

    <para>
      If the -T flag is used to specify an encapsulation type, the
      encapsulation type of the output capture file will be forced to
      the specified type, rather than being the type appropriate to the
      encapsulation type of the input capture file.  Note that this merely
      forces the encapsulation type of the output file to be the specified
      type; the packet headers of the packets will not be translated from the
      encapsulation type of the input capture file to the specified
      encapsulation type (for example, it will not translate an Ethernet
      capture to an FDDI capture if an Ethernet capture is read
      and '-T fddi' is specified).
    </para>
    <example id="AppToolsmergecapEx">
      <title>Help information available from mergecap</title>
      <programlisting>
Mergecap 1.11.0 (SVN Rev 52564 from /trunk)
Merge two or more capture files into one.
See http://www.wireshark.org for more information.

Usage: mergecap [options] -w &lt;outfile&gt;|- &lt;infile&gt; [&lt;infile&gt; ...]

Output:
  -a                concatenate rather than merge files.
                    default is to merge based on frame timestamps.
  -s &lt;snaplen&gt;      truncate packets to &lt;snaplen&gt; bytes of data.
  -w &lt;outfile&gt;|-    set the output filename to &lt;outfile&gt; or '-' for stdout.
  -F &lt;capture type&gt; set the output file type; default is pcapng.
                    an empty "-F" option will list the file types.
  -T &lt;encap type&gt;   set the output file encapsulation type;
                    default is the same as the first input file.
                    an empty "-T" option will list the encapsulation types.

Miscellaneous:
  -h                display this help and exit.
  -v                verbose output.
      </programlisting>
    </example>
    <para>
      A simple example merging <filename>dhcp-capture.libpcap</filename>
      and <filename>imap-1.libpcap</filename> into
      <filename>outfile.libpcap</filename> is shown below.
    </para>
    <example id="AppToolsmergecapExSimple">
      <title>Simple example of using mergecap</title>
      <programlisting>$ mergecap -w outfile.libpcap dhcp-capture.libpcap imap-1.libpcap
      </programlisting>
    </example>
  </section>

  <section id="AppToolstext2pcap" >
    <title><command>text2pcap</command>: Converting ASCII hexdumps to network
    captures
    </title>
    <para>
      There may be some occasions when you wish to convert a hex dump of some
      network traffic into a libpcap file.</para>
    <para>
      <command>Text2pcap</command> is a program that reads in an ASCII hex
      dump and writes the data described into a libpcap-style capture file.
      text2pcap can read hexdumps with multiple packets in them, and build a
      capture file of multiple packets. text2pcap is also capable of
      generating dummy Ethernet, IP and UDP headers, in order to build fully
      processable packet dumps from hexdumps of application-level data only.
    </para>
    <para>
      Text2pcap understands a hexdump of the form generated by od -A x -t x1. In
      other words, each byte is individually displayed and surrounded with a
      space. Each line begins with an offset describing the position in the
      file. The offset is a hex number (can also be octal - see -o), of
      more than two hex digits. Here is a sample dump that text2pcap can
      recognize:
    </para>
    <programlisting>
000000 00 e0 1e a7 05 6f 00 10 ........
000008 5a a0 b9 12 08 00 46 00 ........
000010 03 68 00 00 00 00 0a 2e ........
000018 ee 33 0f 19 08 7f 0f 19 ........
000020 03 80 94 04 00 00 10 01 ........
000028 16 a2 0a 00 03 50 00 0c ........
000030 01 01 0f 19 03 80 11 01 ........
    </programlisting>
    <para>
      There is no limit on the width or number of bytes per line. Also the
      text dump at the end of the line is ignored. Bytes/hex numbers can be
      uppercase or lowercase. Any text before the offset is ignored,
      including email forwarding characters '&gt;'. Any lines of text
      between the bytestring lines is ignored. The offsets are used to
      track the bytes, so offsets must be correct. Any line which has only
      bytes without a leading offset is ignored. An offset is recognized
      as being a hex number longer than two characters. Any text after the
      bytes is ignored (e.g. the character dump). Any hex numbers in this
      text are also ignored. An offset of zero is indicative of starting a
      new packet, so a single text file with a series of hexdumps can be
      converted into a packet capture with multiple packets. Multiple
      packets are read in with timestamps differing by one second each.
      In general, short of these restrictions, text2pcap is pretty liberal
      about reading in hexdumps and has been tested with a variety of mangled
      outputs (including being forwarded through email multiple times,
      with limited line wrap etc.)
    </para>
    <para>
      There are a couple of other special features to note. Any line where
      the first non-whitespace character is '#' will be ignored as a
      comment. Any line beginning with #TEXT2PCAP is a directive and options
      can be inserted after this command to be processed by text2pcap.
      Currently there are no directives implemented; in the future, these
      may be used to give more fine grained control on the dump and the
      way it should be processed e.g. timestamps, encapsulation type etc.
    </para>
    <para>
      Text2pcap also allows the user to read in dumps of application-level
      data, by inserting dummy L2, L3 and L4 headers before each packet.
      Possibilities include inserting headers such as Ethernet, Ethernet + IP,
      Ethernet + IP + UDP, or Ethernet + Ip + TCP before each packet.
      This allows Wireshark or any other full-packet decoder to handle these dumps.
    </para>
    <example id="AppToolstext2pcapEx">
      <title>Help information available from text2pcap</title>
      <programlisting>
Text2pcap 1.11.0 (SVN Rev 52564 from /trunk)
Generate a capture file from an ASCII hexdump of packets.
See http://www.wireshark.org for more information.

Usage: text2pcap [options] &lt;infile&gt; &lt;outfile&gt;

where  &lt;infile&gt; specifies input  filename (use - for standard input)
      &lt;outfile&gt; specifies output filename (use - for standard output)

Input:
  -o hex|oct|dec         parse offsets as (h)ex, (o)ctal or (d)ecimal;
                         default is hex.
  -t &lt;timefmt&gt;           treat the text before the packet as a date/time code;
                         the specified argument is a format string of the sort
                         supported by strptime.
                         Example: The time "10:15:14.5476" has the format code
                         "%H:%M:%S."
                         NOTE: The subsecond component delimiter, '.', must be
                         given, but no pattern is required; the remaining
                         number is assumed to be fractions of a second.
                         NOTE: Date/time fields from the current date/time are
                         used as the default for unspecified fields.
  -D                     the text before the packet starts with an I or an O,
                         indicating that the packet is inbound or outbound.
                         This is only stored if the output format is PCAP-NG.
  -a                     enable ASCII text dump identification.
                         The start of the ASCII text dump can be identified
                         and excluded from the packet data, even if it looks
                         like a HEX dump.
                         NOTE: Do not enable it if the input file does not
                         contain the ASCII text dump.

Output:
  -l &lt;typenum&gt;           link-layer type number; default is 1 (Ethernet).  See
                         http://www.tcpdump.org/linktypes.html for a list of
                         numbers.  Use this option if your dump is a complete
                         hex dump of an encapsulated packet and you wish to
                         specify the exact type of encapsulation.
                         Example: -l 7 for ARCNet packets.
  -m &lt;max-packet&gt;        max packet length in output; default is 65535

Prepend dummy header:
  -e &lt;l3pid&gt;             prepend dummy Ethernet II header with specified L3PID
                         (in HEX).
                         Example: -e 0x806 to specify an ARP packet.
  -i &lt;proto&gt;             prepend dummy IP header with specified IP protocol
                         (in DECIMAL).
                         Automatically prepends Ethernet header as well.
                         Example: -i 46
  -4 &lt;srcip&gt;,&lt;destip&gt;    prepend dummy IPv4 header with specified
                         dest and source address.
                         Example: -4 10.0.0.1,10.0.0.2
  -6 &lt;srcip&gt;,&lt;destip&gt;    replace IPv6 header with specified
                         dest and source address.
                         Example: -6 fe80:0:0:0:202:b3ff:fe1e:8329, 2001:0db8:85a3:0000:0000:8a2e:0370:7334
  -u &lt;srcp&gt;,&lt;destp&gt;      prepend dummy UDP header with specified
                         source and destination ports (in DECIMAL).
                         Automatically prepends Ethernet &amp; IP headers as well.
                         Example: -u 1000,69 to make the packets look like
                         TFTP/UDP packets.
  -T &lt;srcp&gt;,&lt;destp&gt;      prepend dummy TCP header with specified
                         source and destination ports (in DECIMAL).
                         Automatically prepends Ethernet &amp; IP headers as well.
                         Example: -T 50,60
  -s &lt;srcp&gt;,&lt;dstp&gt;,&lt;tag&gt; prepend dummy SCTP header with specified
                         source/dest ports and verification tag (in DECIMAL).
                         Automatically prepends Ethernet &amp; IP headers as well.
                         Example: -s 30,40,34
  -S &lt;srcp&gt;,&lt;dstp&gt;,&lt;ppi&gt; prepend dummy SCTP header with specified
                         source/dest ports and verification tag 0.
                         Automatically prepends a dummy SCTP DATA
                         chunk header with payload protocol identifier ppi.
                         Example: -S 30,40,34

Miscellaneous:
  -h                     display this help and exit.
  -d                     show detailed debug of parser states.
  -q                     generate no output at all (automatically disables -d).
  -n                     use PCAP-NG instead of PCAP as output format.
      </programlisting>
    </example>
  </section>

  <section id="AppToolsidl2wrs" >
    <title><command>idl2wrs</command>:
      Creating dissectors from CORBA IDL files
    </title>
    <para>
      In an ideal world idl2wrs would be mentioned in the users guide
      in passing and documented in the developers guide.  As the
      developers guide
      has not yet been completed it will be documented here.
    </para>
    <section>
      <title>What is it?</title>
      <para>
    As you have probably guessed from the name,
    <command>idl2wrs</command> takes a
    user specified IDL file and attempts to build a dissector that
    can decode the IDL traffic over GIOP. The resulting file is
    "C" code, that should compile okay as a Wireshark dissector.
      </para>
      <para>
    <command>idl2wrs</command> basically parses the data struct given to
    it by the omniidl compiler, and using the GIOP API available in
    packet-giop.[ch], generates  get_CDR_xxx calls to decode the
    CORBA traffic on the wire.
      </para>
      <para>It consists of 4 main files.</para>
      <variablelist>
    <varlistentry><term><filename>README.idl2wrs</filename></term>
      <listitem>
        <para>This document</para>
      </listitem>
    </varlistentry>
    <varlistentry><term><filename>wireshark_be.py</filename></term>
      <listitem>
        <para>The main compiler backend</para>
      </listitem>
    </varlistentry>
    <varlistentry><term><filename>wireshark_gen.py</filename></term>
      <listitem>
        <para>A helper class, that generates the C code.</para>
      </listitem>
    </varlistentry>
    <varlistentry><term><filename>idl2wrs</filename></term>
      <listitem>
        <para> A simple shell script wrapper that the end user should
          use to generate the dissector from the IDL file(s).</para>
      </listitem>
    </varlistentry>
      </variablelist>
    </section>
    <section>
      <title>Why do this?</title>
      <para>
    It is important to understand what CORBA traffic looks
    like over GIOP/IIOP, and to help build a tool that can assist
    in troubleshooting CORBA interworking. This was especially the
    case after seeing a lot of discussions about how particular
    IDL types are represented inside an octet stream.
      </para>
      <para>
    I have also had comments/feedback that this tool would be good for say
    a CORBA class when teaching students what CORBA traffic looks like
    "on the wire".
      </para>
      <para>
    It is also COOL to work on a great Open Source project such as
    the case with "Wireshark" (
    <ulink url="&WiresharkWebSite;">&WiresharkWebSite;</ulink>
    )
      </para>
    </section>
    <section><title>How to use idl2wrs</title>
      <para>
    To use the idl2wrs to generate Wireshark dissectors, you
    need the following:
      </para>
      <orderedlist>
    <title>Prerequisites to using idl2wrs</title>
    <listitem>
      <para>
        Python must be installed.  See
        <ulink url="http://python.org/"/>
      </para>
    </listitem>
    <listitem>
      <para>
        omniidl from the omniORB package must be available. See
        <ulink url="http://omniorb.sourceforge.net/"/>
      </para>
    </listitem>
    <listitem>
      <para>
        Of course you need Wireshark installed to compile the
        code and tweak it if required. idl2wrs is part of the
        standard Wireshark distribution
      </para>
    </listitem>
      </orderedlist>
      <para>
    To use idl2wrs to generate an Wireshark dissector from an idl file
    use the following procedure:
      </para>
      <orderedlist>
    <title>
      Procedure for converting a CORBA idl file into a Wireshark
      dissector
    </title>
    <listitem>
      <para>
        To write the C code to stdout.
        <programlisting>idl2wrs  &lt;your_file.idl&gt;</programlisting>
        e.g.: <programlisting>idl2wrs echo.idl</programlisting>
      </para>
    </listitem>
    <listitem>
      <para>
        To write to a file, just redirect the output.
        <programlisting>idl2wrs echo.idl > packet-test-idl.c</programlisting>
        You may wish to comment out the register_giop_user_module() code
        and that will leave you with heuristic dissection.
      </para>
    </listitem>
      </orderedlist>
      <para>
    If you don't want to use the shell script wrapper, then try
    steps 3 or 4 instead.</para>
      <orderedlist continuation="continues">
    <listitem>
      <para>To write the C code to stdout.
        <programlisting>Usage: omniidl  -p ./ -b wireshark_be &lt;your file.idl&gt;</programlisting>
        e.g.:
        <programlisting>omniidl  -p ./ -b wireshark_be echo.idl</programlisting>
      </para>
    </listitem>
    <listitem>
      <para>
        To write to a file, just redirect the output.
        <programlisting>omniidl  -p ./ -b wireshark_be echo.idl > packet-test-idl.c</programlisting>
        You may wish to comment out the register_giop_user_module() code
        and that will leave you with heuristic dissection.
      </para>
    </listitem>
    <listitem>
      <para>
        Copy the resulting C code to subdirectory epan/dissectors/ inside your
        Wireshark source directory.
        <programlisting>cp packet-test-idl.c /dir/where/wireshark/lives/epan/dissectors/</programlisting>
        The new dissector has to be added to Makefile.common in the same
        directory. Look for the declaration CLEAN_DISSECTOR_SRC and add
        the new dissector there. For example,
        <programlisting>
CLEAN_DISSECTOR_SRC = \
        packet-2dparityfec.c    \
        packet-3com-njack.c     \
        ...
            </programlisting>
            becomes
        <programlisting>
CLEAN_DISSECTOR_SRC = \
        packet-test-idl.c       \
        packet-2dparityfec.c    \
        packet-3com-njack.c     \
        ...
            </programlisting>
      </para>
          <para>
          For the next steps, go up to the top of your Wireshark source directory.
          </para>
    </listitem>
    <listitem>
      <para>Run configure
        <programlisting>./configure (or ./autogen.sh)</programlisting>
      </para>
    </listitem>
    <listitem>
      <para> Compile the code
        <programlisting>make</programlisting>
      </para>
    </listitem>
    <listitem>
      <para>Good Luck !!</para>
    </listitem>
      </orderedlist>
    </section>
    <section><title>TODO</title>
      <orderedlist>
    <listitem>
      <para>
        Exception code not generated  (yet), but can be added manually.
      </para>
    </listitem>
    <listitem>
      <para>
        Enums not converted to symbolic values (yet), but can be added
        manually.
      </para>
    </listitem>
    <listitem>
      <para>Add command line options etc</para>
    </listitem>
    <listitem>
      <para>More I am sure :-)</para>
    </listitem>
      </orderedlist>
    </section>
    <section><title>Limitations</title>
      <para>
    See the TODO list inside <filename>packet-giop.c</filename>
      </para>
    </section>
    <section><title>Notes</title>
      <orderedlist>
    <listitem>
      <para>
        The "-p ./" option passed to omniidl indicates that the
        wireshark_be.py and wireshark_gen.py are residing in the
        current directory. This may need
        tweaking if you place these files somewhere else.
      </para>
    </listitem>
    <listitem>
      <para>
        If it complains about being unable to find some modules
        (e.g. tempfile.py),
        you may want to check if PYTHONPATH is set correctly.
        On my Linux box, it is  PYTHONPATH=/usr/lib/python2.4/
      </para>
    </listitem>
      </orderedlist>
    </section>
  </section>
  <section id="AppToolsreordercap" >
    <title><command>reordercap</command>: Reorder a capture file
    </title>
    <para>
      Reordercap allows to reorder a capture file according to the packets timestamp.
    </para>
    <example id="AppToolsreordercapEx">
      <title>Help information available from reordercap</title>
      <programlisting>
Reordercap 1.11.0
Reorder timestamps of input file frames into output file.
See http://www.wireshark.org for more information.

Usage: reordercap [options] &lt;infile&gt; &lt;outfile&gt;

Options:
  -n        don't write to output file if the input file is ordered.
      </programlisting>
    </example>
  </section>
</appendix>
<!-- End of WSUG Appendix Tools -->