1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
|
#ifndef _BOARD_
#define _BOARD_
/** Headers */
#include "chip.h"
/* We need this for a nop instruction in USB_HAL.c */
#define __CC_ARM
/** Board */
#include "board_lowlevel.h"
#include "uart_console.h"
#include "iso7816_4.h"
#include "led.h"
#include "cciddriver.h"
#include "USBD.h"
#include "USBD_Config.h"
#include "USBDDriver.h"
/** Highlevel */
#include "trace.h"
#include "stdio.h"
#include "stdlib.h"
#include "string.h"
#include "inttypes.h"
#include "simtrace.h"
#define MIN(a, b) ((a < b) ? a : b)
#ifdef __GNUC__
#undef __GNUC__
#endif
/** Name of the board */
#define BOARD_NAME "SAM3S-SIMTRACE"
/** Board definition */
#define simtrace
/** Family definition (already defined) */
#define sam3s
/** Core definition */
#define cortexm3
#define BOARD_MAINOSC 18432000
#define BOARD_MCK 48000000
#define LED_RED PIO_PA17
#define LED_GREEN PIO_PA18
#define PIN_LED_RED {LED_RED, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
#define PIN_LED_GREEN {LED_GREEN, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
#define PINS_LEDS PIN_LED_RED, PIN_LED_GREEN
#define LED_NUM_RED 0
#define LED_NUM_GREEN 1
/** Phone (SIM card emulator)/CCID Reader/MITM configuration **/
/* Normally the communication lines between phone and SIM card are disconnected */
// Disconnect SIM card I/O, VPP line from the phone lines
// FIXME: Per default pins are input, therefore high-impedance, therefore they don not activate the bus switch, right?
#define PIN_SC_SW_DEFAULT {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
// Disconnect SIM card RST, CLK line from the phone lines
#define PIN_IO_SW_DEFAULT {PIO_PA19, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
#define PINS_BUS_DEFAULT PIN_SC_SW_DEFAULT, PIN_IO_SW_DEFAULT
/** Sniffer configuration **/
// Connect VPP, CLK and RST lines from smartcard to the phone
#define PIN_SC_SW_SNIFF {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
#define PIN_IO_SW_SNIFF {PIO_PA19, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
#define PINS_BUS_SNIFF PIN_SC_SW_SNIFF, PIN_IO_SW_SNIFF
#define PINS_SIM_SNIFF_SIM PIN_PHONE_IO, PIN_PHONE_CLK
/** USART0 pin RX */
#define PIN_USART0_RXD {PIO_PA9A_URXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/** USART0 pin TX */
#define PIN_USART0_TXD {PIO_PA10A_UTXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define BOARD_PIN_USART_RXD PIN_USART0_RXD
#define BOARD_PIN_USART_TXD PIN_USART0_TXD
#define BOARD_ID_USART ID_USART0
#define BOARD_USART_BASE USART0
#define PINS_UART { PIO_PA9A_URXD0|PIO_PA10A_UTXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/** UART0 */
/** Console baudrate always using 115200. */
#define CONSOLE_BAUDRATE 115200
/** Usart Hw interface used by the console (UART0). */
#define CONSOLE_USART UART0
/** Usart Hw ID used by the console (UART0). */
#define CONSOLE_ID ID_UART0
/** Pins description corresponding to Rxd,Txd, (UART pins) */
#define CONSOLE_PINS {PINS_UART}
/// Smartcard detection pin
// FIXME: add connect pin as iso pin...should it be periph b or interrupt oder input?
#define BOARD_ISO7816_BASE_USART USART0
#define BOARD_ISO7816_ID_USART ID_USART0
#define USART_SIM USART0
#define ID_USART_SIM ID_USART0
#define USART_PHONE USART1
#define ID_USART_PHONE ID_USART1
#define SIM_PWEN PIO_PA5
#define VCC_FWD PIO_PA26
#define SIM_PWEN_PIN {PIO_PA5, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
#define PWR_PINS \
/* Enable power converter 4.5-6V to 3.3V; low: off */ \
{SIM_PWEN, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}, \
/* Enable second power converter: VCC_PHONE to VCC_SIM; high: on */ \
{VCC_FWD, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
#define SW_SIM PIO_PA8
#define SMARTCARD_CONNECT_PIN {SW_SIM, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_DEGLITCH | PIO_IT_EDGE }
//#define SMARTCARD_CONNECT_PIN {SW_SIM, PIOB, ID_PIOB, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_IT_EDGE}
/// PIN used for resetting the smartcard
#define RST_SIM (1 << 7)
// FIXME: Card is resetted with pin set to 0 --> PIO_OUTPUT_1 as default is right?
#define PIN_ISO7816_RSTMC {RST_SIM, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
/// Pins used for connect the smartcard
#define PIN_SIM_IO_INPUT {PIO_PA1, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
#define PIN_SIM_IO {PIO_PA6, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_SIM_CLK {PIO_PA2, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
#define PIN_SIM_CLK_INPUT {PIO_PA4, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
//#define PINS_ISO7816 PIN_USART1_TXD, PIN_USART1_SCK, PIN_ISO7816_RSTMC
#define PINS_ISO7816 PIN_SIM_IO, PIN_SIM_CLK, PIN_ISO7816_RSTMC // SIM_PWEN_PIN, PIN_SIM_IO2, PIN_SIM_CLK2
#define PINS_TC PIN_SIM_IO_INPUT, PIN_SIM_CLK_INPUT
#define VCC_PHONE {PIO_PA25, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
#define PIN_ISO7816_RST_PHONE {PIO_PA24, PIOA, ID_PIOA, PIO_INPUT, PIO_IT_RISE_EDGE }
#define PIN_PHONE_IO_INPUT {PIO_PA21, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
#define PIN_PHONE_IO {PIO_PA22, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_PHONE_CLK {PIO_PA23A_SCK1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} // External Clock Input on PA28
//#define PIN_PHONE_CLK {PIO_PA23A_SCK1, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT} // External Clock Input on PA28
#define PIN_PHONE_CLK_INPUT {PIO_PA29, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
#define PINS_ISO7816_PHONE PIN_PHONE_IO, PIN_PHONE_CLK, PIN_ISO7816_RST_PHONE
//, VCC_PHONE
//** SPI interface **/
/// SPI MISO pin definition (PA12).
#define PIN_SPI_MISO {1 << 12, PIOA, PIOA, PIO_PERIPH_A, PIO_PULLUP}
/// SPI MOSI pin definition (PA13).
#define PIN_SPI_MOSI {1 << 13, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/// SPI SPCK pin definition (PA14).
#define PIN_SPI_SPCK {1 << 14, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/// SPI pins definition. Contains MISO, MOSI & SPCK (PA12, PA13 & PA14).
#define PINS_SPI PIN_SPI_MISO, PIN_SPI_MOSI, PIN_SPI_SPCK
/// SPI chip select 0 pin definition (PA11).
#define PIN_SPI_NPCS0 {1 << 11, PIOA, PIOA, PIO_PERIPH_A, PIO_DEFAULT}
//** USB **/
// USB pull-up control pin definition (PA16).
// Default: 1 (USB Pullup deactivated)
#define PIN_USB_PULLUP {1 << 16, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
// Board has UDP controller
#define BOARD_USB_UDP
// D+ has external pull-up
#define BOARD_USB_PULLUP_EXTERNAL
#define BOARD_USB_NUMENDPOINTS 8
// FIXME: in all other cases return 0?
#define BOARD_USB_ENDPOINTS_MAXPACKETSIZE(i) (((i == 4) || (i == 5))? 512 : 64)
#define BOARD_USB_ENDPOINTS_BANKS(i) (((i == 0) || (i == 3)) ? 1 : 2)
/// USB attributes configuration descriptor (bus or self powered, remote wakeup)
//#define BOARD_USB_BMATTRIBUTES USBConfigurationDescriptor_SELFPOWERED_NORWAKEUP
#define BOARD_USB_BMATTRIBUTES USBConfigurationDescriptor_BUSPOWERED_NORWAKEUP
//#define BOARD_USB_BMATTRIBUTES USBConfigurationDescriptor_SELFPOWERED_RWAKEUP
#define ATMEL_VENDOR_ID 0x03EB
#define SIMTRACE_PRODUCT_ID 0x6004
//#define OPENPCD_VENDOR_ID 0x16c0
//#define SIMTRACE_PRODUCT_ID 0x0762
#define USB_VENDOR_ID OPENPCD_VENDOR_ID
#define USB_PRODUCT_ID SIMTRACE_PRODUCT_ID
#endif
|
