Age | Commit message (Expand) | Author | Files | Lines |
2019-09-03 | schematic: make it more readable | Kévin Redon | 3 | -1736/+1622 |
2019-08-27 | updated libraries to KiCad 5 | Kévin Redon | 4 | -468/+1272 |
2019-08-27 | remove unused cable project | Kévin Redon | 4 | -399/+0 |
2015-07-05 | change microcontroller to SAM3S | King Kévin | 3 | -6879/+7148 |
2014-06-23 | export schematic, and pcb (with minor esthetic corrections) | Kevin Redon | 1 | -6272/+6204 |
2014-06-20 | v1.4: Connect PA0 to 3V3; pull-up for PA1/PA2 (R25,R26) | Harald Welte | 2 | -1961/+2007 |
2014-06-20 | Schematic: Make sure PA0 to PA2 are high on power-up | Harald Welte | 1 | -353/+205 |
2013-11-11 | simtrace 1.3: move point of origin to lower left corner of PCB | Harald Welte | 1 | -5550/+5550 |
2013-10-28 | BOM corrected (sorted by value) and reformated | Kevin Redon | 3 | -34/+15 |
2013-10-27 | MCU pin 48 used to identify v1.3 by putting it to ground (with internal pull-up) | Kevin Redon | 5 | -21794/+6086 |
2013-10-27 | exported fabrication files | Kevin Redon | 1 | -25/+2 |
2013-10-27 | new components placed and routed | Kevin Redon | 1 | -1679/+1643 |
2013-10-27 | MBR0530 pin numbers corrected | Kevin Redon | 6 | -228/+251 |
2013-10-27 | new KiCAD layout format, silkscreen refdes 0.5mm, text 0.75mm, new components... | Kevin Redon | 1 | -0/+10632 |
2013-10-27 | set footprints to symbols | Kevin Redon | 1 | -17/+45 |
2013-10-27 | exported v1.3 netlist | Kevin Redon | 1 | -1005/+1135 |
2013-10-27 | v1.3 modifications: replaced IC switch with FPF2109, added schottky and pull-... | Kevin Redon | 1 | -166/+390 |
2013-10-27 | added FPF210X symbol to library | Kevin Redon | 3 | -3/+62 |
2012-05-18 | RST_PHONE pulldown added on PCB | Kevin Redon | 3 | -1381/+1790 |
2012-05-17 | Add R23 (pull-up for !SIM_RST signal) | Harald Welte | 1 | -47/+58 |
2012-05-16 | v1.2p fabrication exported | Kevin Redon | 3 | -50/+46 |
2012-05-16 | C14 change to 4.7uF 0805, silkscreen improved, more space for JTAG | Kevin Redon | 4 | -1912/+1334 |
2012-05-15 | DRC rules violations corrected | Kevin Redon | 1 | -657/+517 |
2012-05-15 | SIMtrace: Improve PCB routing of GND, 3V3 and VCC traces | Harald Welte | 1 | -4148/+5879 |
2011-11-05 | hw: sysmocom added to copper, gerber rendered | Kevin Redon | 2 | -187/+2339 |
2011-11-05 | hw: solder mask between at91sam7s added | Kevin Redon | 1 | -325/+3996 |
2011-11-05 | VPP connected through bus switch | Kevin Redon | 3 | -5287/+1915 |
2011-11-03 | +1.8V line enlarged on C12, C15, C16. not possible on C19 | Kevin Redon | 1 | -225/+184 |
2011-11-03 | footprint refreched, cap near LDO | Kevin Redon | 5 | -2112/+2151 |
2011-11-01 | ftdi 3.3v cut in schema | Kevin Redon | 1 | -17/+4 |
2011-07-02 | v1.0p corrected and rendered. BOM updatedv1.0_production | Kevin Redon | 1 | -73/+89 |
2011-07-02 | D2 and D3 now also use STPS340U instead of 1N5819 | Kevin Redon | 4 | -593/+505 |
2011-07-02 | PS/gerber rendered for production | Kevin Redon | 1 | -300/+167 |
2011-07-02 | board adapted to new footprints | Kevin Redon | 1 | -1262/+1652 |
2011-07-02 | new footprints select for production in netlist (LED is 0805, schottky is SMB... | Kevin Redon | 5 | -1187/+807 |
2011-07-02 | footprints for flash S25FL016A and schottky STPS340U created | Kevin Redon | 1 | -0/+104 |
2011-06-23 | BOM updated | Kevin Redon | 3 | -555/+866 |
2011-06-23 | ps/gerber rerendered for the thermal footprints | Kevin Redon | 1 | -1/+1 |
2011-06-23 | thermal pads were missing on the bottom layer on the PCB in kicad | Kevin Redon | 1 | -128/+658 |
2011-06-23 | backup module file removed | Kevin Redon | 1 | -182/+0 |
2011-06-23 | simcable footprints added and linked to schema in the netlist | Kevin Redon | 4 | -81/+245 |
2011-06-21 | v1.0 released. board version added, output (schema,gerber) rendered | Kevin Redon | 3 | -5711/+8234 |
2011-06-21 | rebelSIM PCB SIM card for FFC (flat flexible cable) schema created. we could ... | Kevin Redon | 7 | -10/+471 |
2011-06-21 | antenna logo to put on the PCB, but it's not used because there is an unknown... | Kevin Redon | 3 | -0/+51 |
2011-06-21 | output rendered | Kevin Redon | 3 | -262/+338 |
2011-06-21 | VCC track increased, name added | Kevin Redon | 2 | -882/+3361 |
2011-06-21 | diode indicator added | Kevin Redon | 1 | -2326/+67 |
2011-06-20 | routing redone | Kevin Redon | 2 | -4292/+6458 |
2011-06-20 | LDO, and power switch added. not verified yet | Kevin Redon | 13 | -4506/+4736 |
2011-06-20 | better ADC, LDO changed | Kevin Redon | 5 | -205/+291 |