Age | Commit message (Expand) | Author | Files | Lines |
2019-10-01 | schematic: add DNP note on JTAG and UART debug connectorsv1.5 | Kévin Redon | 1 | -60/+64 |
2019-09-03 | schematic: mark USB reset circuit as dot no place | Kévin Redon | 1 | -5/+14 |
2019-09-03 | schematic: mark R19 as dot no place | Kévin Redon | 1 | -0/+2 |
2019-09-03 | schematic: rename NP to DNP for clarity | Kévin Redon | 1 | -9/+9 |
2019-09-03 | schematic: mark JP1 and JP2 as dot no place | Kévin Redon | 1 | -0/+4 |
2019-09-03 | schematic: mark R22 as dot no place | Kévin Redon | 1 | -0/+2 |
2019-09-03 | schematic: mark R24 as no place | Kévin Redon | 1 | -26/+28 |
2019-09-03 | schematic: mark R15 as no place | Kévin Redon | 1 | -4/+8 |
2019-09-03 | schematic: make it more readable | Kévin Redon | 1 | -1735/+1596 |
2019-08-27 | updated libraries to KiCad 5 | Kévin Redon | 1 | -427/+598 |
2015-07-05 | change microcontroller to SAM3S | King Kévin | 1 | -6/+188 |
2014-06-20 | Schematic: Make sure PA0 to PA2 are high on power-up | Harald Welte | 1 | -353/+205 |
2013-10-28 | BOM corrected (sorted by value) and reformated | Kevin Redon | 1 | -13/+5 |
2013-10-27 | MCU pin 48 used to identify v1.3 by putting it to ground (with internal pull-up) | Kevin Redon | 1 | -10/+24 |
2013-10-27 | MBR0530 pin numbers corrected | Kevin Redon | 1 | -4/+4 |
2013-10-27 | v1.3 modifications: replaced IC switch with FPF2109, added schottky and pull-... | Kevin Redon | 1 | -166/+390 |
2012-05-18 | RST_PHONE pulldown added on PCB | Kevin Redon | 1 | -113/+120 |
2012-05-17 | Add R23 (pull-up for !SIM_RST signal) | Harald Welte | 1 | -47/+58 |
2012-05-16 | v1.2p fabrication exported | Kevin Redon | 1 | -2/+2 |
2012-05-16 | C14 change to 4.7uF 0805, silkscreen improved, more space for JTAG | Kevin Redon | 1 | -5/+4 |
2011-11-05 | VPP connected through bus switch | Kevin Redon | 1 | -114/+150 |
2011-11-03 | footprint refreched, cap near LDO | Kevin Redon | 1 | -18/+18 |
2011-11-01 | ftdi 3.3v cut in schema | Kevin Redon | 1 | -17/+4 |
2011-07-02 | D2 and D3 now also use STPS340U instead of 1N5819 | Kevin Redon | 1 | -6/+7 |
2011-07-02 | new footprints select for production in netlist (LED is 0805, schottky is SMB... | Kevin Redon | 1 | -7/+6 |
2011-06-23 | BOM updated | Kevin Redon | 1 | -7/+7 |
2011-06-21 | v1.0 released. board version added, output (schema,gerber) rendered | Kevin Redon | 1 | -3/+4 |
2011-06-21 | output rendered | Kevin Redon | 1 | -6/+13 |
2011-06-20 | LDO, and power switch added. not verified yet | Kevin Redon | 1 | -157/+220 |
2011-06-20 | better ADC, LDO changed | Kevin Redon | 1 | -201/+267 |
2011-06-20 | bus switch CB3q3244 used instead of QS3244 | Kevin Redon | 1 | -12/+12 |
2011-06-19 | VCC_PHONE connected to GPIO | Kevin Redon | 1 | -364/+366 |
2011-06-19 | SIM_SW connected to GND, components moved | Kevin Redon | 1 | -18/+18 |
2011-06-15 | better routing | Kevin Redon | 1 | -90/+66 |
2011-06-15 | second gnd added for TPS73633 | Kevin Redon | 1 | -35/+42 |
2011-06-15 | UDP_PUP now connected to PA16 (pin 19) on schema | Kevin Redon | 1 | -370/+368 |
2011-06-15 | BC847 footprint corrected | Kevin Redon | 1 | -3/+4 |
2011-05-22 | debug port changed | Kevin Redon | 1 | -3/+2 |
2011-05-15 | kevin local new versin enforced | Kevin Redon | 1 | -2/+2 |
2011-05-13 | update kicad project to v0.9+ | Kevin Redon | 1 | -53/+94 |
2011-05-13 | update kicad project to v0.9 | Kevin Redon | 1 | -706/+596 |
2011-05-13 | update kicad project to v0.8 | Kevin Redon | 1 | -810/+741 |
2011-05-13 | update kicad project to v0.7+ | Kevin Redon | 1 | -375/+773 |
2011-05-13 | update kicad project to v0.7 | Kevin Redon | 1 | -669/+813 |
2011-05-13 | Update kicad project to v0.6 | Kevin Redon | 1 | -825/+736 |
2011-05-13 | Update kicad project to SIMtrace v0.5 | Kevin Redon | 1 | -962/+1051 |
2011-05-13 | rename from SIMtrace to SIMtrace | Kevin Redon | 1 | -0/+1561 |