Age | Commit message (Collapse) | Author | Files | Lines | |
---|---|---|---|---|---|
2013-11-16 | add datasheet of SPI flash component mounted on recent boardsv1.3 | Harald Welte | 1 | -0/+0 | |
At some point during v1.2p production, we switched from the S25FL016 to the S25FL032P SPI flash model. v1.3 all have that flash (so far). | |||||
2013-11-11 | simtrace 1.3: move point of origin to lower left corner of PCB | Harald Welte | 3 | -5608/+5608 | |
2013-10-28 | merge | Kevin Redon | 1 | -0/+0 | |
2013-10-28 | BOM corrected (sorted by value) and reformated | Kevin Redon | 4 | -90/+56 | |
2013-10-27 | re-add BOM spreadsheet with updated v1.3 components | Harald Welte | 1 | -0/+0 | |
2013-10-27 | MCU pin 48 used to identify v1.3 by putting it to ground (with internal pull-up) | Kevin Redon | 28 | -190009/+89694 | |
2013-10-27 | exported fabrication files | Kevin Redon | 40 | -182715/+148043 | |
2013-10-27 | new components placed and routed | Kevin Redon | 1 | -1679/+1643 | |
2013-10-27 | MBR0530 pin numbers corrected | Kevin Redon | 6 | -228/+251 | |
2013-10-27 | new KiCAD layout format, silkscreen refdes 0.5mm, text 0.75mm, new ↵ | Kevin Redon | 1 | -0/+10632 | |
components loaded | |||||
2013-10-27 | set footprints to symbols | Kevin Redon | 1 | -17/+45 | |
2013-10-27 | exported v1.3 netlist | Kevin Redon | 1 | -1005/+1135 | |
2013-10-27 | v1.3 modifications: replaced IC switch with FPF2109, added schottky and ↵ | Kevin Redon | 1 | -166/+390 | |
pull-down resistors | |||||
2013-10-27 | added FPF210X symbol to library | Kevin Redon | 3 | -3/+62 | |
2012-05-19 | Mark IC5 as "do not place" (VCC_Forward) as it doesn't work anywayv1.2_production | Harald Welte | 1 | -0/+0 | |
If the LDO is switched off, then even if we try to forward power from the phone to the SIM, the current will sink inside the LDO (no reverse current protection). | |||||
2012-05-18 | RST_PHONE pulldown added on PCB | Kevin Redon | 30 | -6505/+7639 | |
2012-05-17 | Add R23 (pull-up for !SIM_RST signal) | Harald Welte | 1 | -47/+58 | |
While the SAM7 has an internal pull-up, this is of no use if the bus switch input is left open and collects noise resulting in bogus nRST interrupts. | |||||
2012-05-16 | v1.2p fabrication exported | Kevin Redon | 32 | -141627/+88041 | |
2012-05-16 | C14 change to 4.7uF 0805, silkscreen improved, more space for JTAG | Kevin Redon | 4 | -1912/+1334 | |
2012-05-15 | DRC rules violations corrected | Kevin Redon | 1 | -657/+517 | |
2012-05-15 | SIMtrace: Improve PCB routing of GND, 3V3 and VCC traces | Harald Welte | 1 | -4148/+5879 | |
We have to make sure the impedance of the supply lanes is not too high. Particularly bad was passing GND in 0.2mm under several resistors before even reaching the LDO from the USB socket. This attempts to address the major issues. Also, the input capacitor is moved closer to the LDO once again | |||||
2011-12-06 | hw: fabrication output generatedv1.1_production | Kevin Redon | 3 | -188/+187 | |
2011-11-05 | hw: sysmocom added to copper, gerber rendered | Kevin Redon | 20 | -1900/+4487 | |
2011-11-05 | hw: solder mask between at91sam7s added | Kevin Redon | 22 | -34585/+44230 | |
2011-11-05 | VPP connected through bus switch | Kevin Redon | 3 | -5287/+1915 | |
2011-11-03 | +1.8V line enlarged on C12, C15, C16. not possible on C19 | Kevin Redon | 1 | -225/+184 | |
2011-11-03 | footprint refreched, cap near LDO | Kevin Redon | 5 | -2112/+2151 | |
2011-11-01 | ftdi 3.3v cut in schema | Kevin Redon | 1 | -17/+4 | |
2011-07-02 | v1.0p corrected and rendered. BOM updatedv1.0_production | Kevin Redon | 26 | -13810/+9811 | |
2011-07-02 | D2 and D3 now also use STPS340U instead of 1N5819 | Kevin Redon | 6 | -611/+522 | |
2011-07-02 | BOM updated for production | Kevin Redon | 2 | -37/+37 | |
2011-07-02 | PS/gerber rendered for production | Kevin Redon | 25 | -18555/+19764 | |
2011-07-02 | board adapted to new footprints | Kevin Redon | 1 | -1262/+1652 | |
2011-07-02 | new footprints select for production in netlist (LED is 0805, schottky is ↵ | Kevin Redon | 5 | -1187/+807 | |
SMB_STPS340U, flash is SO008_wide | |||||
2011-07-02 | footprints for flash S25FL016A and schottky STPS340U created | Kevin Redon | 1 | -0/+104 | |
2011-07-02 | flash memory S25FL016A replaces SST25VF040B for production. datasheet added | Kevin Redon | 1 | -0/+0 | |
2011-07-02 | schottky STPS340U replaces MBR0530T1 for production. datasheet added | Kevin Redon | 1 | -0/+0 | |
2011-06-23 | BOM updated | Kevin Redon | 5 | -586/+894 | |
2011-06-23 | PCB PS drawings were in the wrong folder | Kevin Redon | 14 | -164700/+3695 | |
2011-06-23 | Merge branch 'master' of git.osmocom.org:simtrace | Kevin Redon | 2 | -0/+40361 | |
2011-06-23 | ps/gerber rerendered for the thermal footprints | Kevin Redon | 21 | -99/+170393 | |
2011-06-23 | thermal pads were missing on the bottom layer on the PCB in kicad | Kevin Redon | 1 | -128/+658 | |
2011-06-23 | backup module file removed | Kevin Redon | 1 | -182/+0 | |
2011-06-23 | simcable footprints added and linked to schema in the netlist | Kevin Redon | 5 | -81/+245 | |
2011-06-21 | add 'release' of gerber and schematics for v1.0 | Harald Welte | 2 | -0/+40361 | |
2011-06-21 | v1.0 released. board version added, output (schema,gerber) rendered | Kevin Redon | 23 | -83663/+200248 | |
2011-06-21 | wrong USB connector from digikey in BOM chosen. corrected : hirose ↵ | Kevin Redon | 1 | -0/+0 | |
UX60-MB-5ST / digikey H2959CT-ND | |||||
2011-06-21 | rebelSIM PCB SIM card for FFC (flat flexible cable) schema created. we could ↵ | Kevin Redon | 7 | -10/+471 | |
produce our own | |||||
2011-06-21 | antenna logo to put on the PCB, but it's not used because there is an ↵ | Kevin Redon | 3 | -0/+51 | |
unknown cleareance issue when filling the area : the picture is partially masked | |||||
2011-06-21 | output rendered | Kevin Redon | 29 | -125067/+80976 | |