Age | Commit message (Collapse) | Author | Files | Lines |
|
Implementation:
PCU keeps track of number PDCH across all the TRXs at BTS context and also keeps number
of active PDCHs in each TRX context. This ratio gives the CAPACITY of each TRX.
1st Phase:
While selection of TRX, functions get_possible_trxs(for multiple TS)
and get_possible_trxs_sba(Single block allocation, Ex: during RACH)
gets possible TRXs based on TFIs availability.
2nd Phase: outcome of TRXs(from get_possible_trxs, get_possible_trxs_sba) will
be fed to get_suitable_trx function. Which does actual load balancing on each TRX.
And selects the best fit TRX, based on below equation
PROBABILITY = MAX_PROBABILITY – ((LOAD * 100)/CAPACITY);
If same PROBABILITY
Select the one with higher capacity
Else
Find the TRX with higher PROBABILITY
MAX_PROBABILITY = 65535;
LOAD: Initialized to 0, Later gets incremented with number of TS allocated.
and decremented whle TBF deletion, based on number of TS allocated
Below are the test executed on Unit test environment
1) 2 TRXs, with same Capacity
2) 2 TRX with ½ capacity
3) 2 TRXs with ¼ capacity
4) 2 TRX with UL and DL allocation to ensure Tbfs on both direction is hosted on same TRX
5) 2 TRX with same Capacity and DL TBF creation and deletion scenarios to ensure proper
load balancing criteria for actual Load.
Below are the Test executed on Integration setup with Ettus B200 setup with 2
TRXs with same CAPACITY.
1) TRX allocation during RACH procedure(SBA allocation)
2) TRX allocation during DL TBF creation with multi time slots(4 time slots)
3) TRX allocation while Ping Test
4) TRX allocation while UDP test
5) TRX allocation for web browsing.
6) 2 MS test with each TRX sharing 1 MS. Received aggregate throughput of
446 kbps(223 Kbps each)
Limitation:
1) BSSGP flow control needs to be tuned since test with 2 MS with each MS on different TRX
runs for 20 mins
2) USF resource availibility is not checked while selecting the TRX as existing implementation
Change-Id: Ifb61a7862d55af828383b6dfe728628e546ed12b
Related: OS# 1775
|
|
When Packet resource request is received, PCU will generate the
packet access reject if no resources are present. The encoding is done
based on section 7.1.3.2.1 and 8.1.2.5 of 44.060 version 7.27.0 Release 7.
This patch also includes the test case to validate the generated
packet access reject message.
This patch is integration tested on Osmo-trx setup with Ettus B210 board
and LG F70 MS with some simulation code changes in Osmo-pcu.
Change-Id: I05ff25124b58905586caa0c0c37023d69724f121
|
|
This adds compression of bitmap in PUAN. The compressed bitmap
is used only if the number of bits in the bitmap does not fit in
the message and there is a gain after compression.
The algorithm is part of libosmocore and so there is dependency
on the libosmocore for compilation.
The algorithm is tested on integration setup by forcing compression.
|
|
Adds spb counters at BTS level(show bts statistics).
Adds RLC/MAC downlink control msg at ms level(show ms imsi <imsi_val>).
Adds the number of coding schemes counter for UL at TBF level.
Change-Id: Icbe4ba95e34bea89ee36f532d099db68204b7c38
|
|
Adds DL throughput in show ms imsi <imsi_value>.
Adds the number of coding schemes counter and rlc nacked counter at TBf level.
Change-Id: Ia95b0404989b00db0e7ba416bc40d09ef41fde1c
|
|
Adds counters for Immediate Assignment Reject, Packet Access Reject,
Channel Request Description and Final Block resend.
Change-Id: I23e326d4ea489aa4967e452fe02773b44ab146f7
|
|
Adds counters for MCS blocks, 11 bit Rach counters and others.
Change-Id: I605b0d66eb217decd35cbb8f87abfa577760245a
|
|
When PDAN/EPDAN with channel description is received, PCU will generate the
packet access reject if no resources are present. The encoding is done
based on section 7.1.3.2.1 and 8.1.2.5 of 44.060 version 7.27.0 Release 7.
This patch also includes the test case to validate the generated
packet access reject message.
This patch is integration tested on Osmo-trx setup with Ettus B210 board
and LG F70 MS with some simulation code changes in Osmo-pcu.
Change-Id: I096a3bb44a65533b9e9b091925dd5f70a8696d6
|
|
This reverts commit f1a7b8fc6651f92a8b7f3f27b7ca05d07f4e44e0.
Conflicts:
tests/tbf/TbfTest.err
The commit broke GPRS service at least for osmo-bts-sysmo on a SysmoBTS 1002
with current master of osmo-bts (ef30f50d5d6d5f863fc147d05ccdceb89284934e).
The error observed is the following log output (was viewing both osmo-bts-sysmo
and osmo-pcu logs interleaved):
<0002> tbf.cpp:874 TBF(TFI=0 TLLI=0x00000000 DIR=UL STATE=WAIT ASSIGN) T3169 timeout during transsmission
<0002> tbf.cpp:893 - Assignment was on CCCH
<0002> tbf.cpp:899 - No uplink data received yet
<0007> l1sap.c:904 RACH for packet access
<0001> pcu_l1_if.cpp:311 RACH request received: sapi=1 qta=0, ra=121, fn=13653
[repeat]
When removing this single commit from current osmo-pcu master, GPRS service
works well on SysmoBTS, with current osmo-bts master.
The TbfTest.err expected output needed adjustment after the revert.
Disclaimer: I am not aware of adverse effects this commit may have. I have no
idea what the WAIT_ASSIGN state is used for -- further review is required.
Change-Id: I1532f8e93194368cdc1e3846f82afa6d68cd5fbd
|
|
gcc6 is optimizing if (!this) {CODE} as this is assumed to never be a
std::nullptr here. Move the null check to the caller. In preparation of
removing the check within llc_queue->size(), all callers must check the object
before calling it. Make sure of that: make the llc_queue() access function
protected and offer only a public llc_queue_size() function that incorporates
the NULL check. All current callers are only interested in the
llc_queue_size().
Tweaked-by: nhofmeyr
Change-Id: I88cc3180f8f86785e3f07981895dabddf50b60a2
|
|
Earlier there was no handling for recalculation of DL window
size during tbf update. Which has been fixed in this patch.
Related: OS#1808
Change-Id: I41aa807068520460fd665a55e3529e60f6bbb630
|
|
A subsequent patch needs to call this from gprs_rlcmac_tbf::update(),
so to avoid code dup, put the calculation in a separate function.
Related: OS#1808
Change-Id: I7c7777d43f843bbd3421503fc2a8600f148ca035
|
|
* initialize with invalid TA instead of making assumption that phone is
located within 550 meters (TA=0)
* only set valid TA
Change-Id: Idfc40ff0c11bdac13d9e28fbfa4e95dfc6b735b0
Related: OS#1526
|
|
All checks of (this == null) will be eliminated by GCC >= 6.1
(https://gcc.gnu.org/gcc-6/changes.html, Value range propagation now
assumes that the this pointer of C++ member functions is non-null.
Change-Id: Ifddaef70bb0a4402050c817b1000d515c3a7118b
Reviewed-on: https://gerrit.osmocom.org/136
Tested-by: Jenkins Builder
Reviewed-by: Harald Welte <laforge@gnumonks.org>
Reviewed-by: Holger Freyther <holger@freyther.de>
|
|
Currently the state on the TBF is set to ASSIGN when it is created
and in general changed to FLOW when it is acknowledged by the MS. The
moment when the assignment is really transmitted to the MS (which can
take some time) is not reflected by the state. A TBF can considered
to be valid, when the assignment is received by the MS.
Add the state WAIT_ASSIGN that is entered when the assigment has been
send to the MS (more precisely: when the corresponding RTS has been
processed or the message has been sent to the BTS).
The TBF, its PDCH(s), and its TFI can be assumed to be valid, when the
TBF has a state of WAIT_ASSIGN or higher (assuming that the TBF
starting time has not been set, which is currently only done for SBA,
which are not associated with a TBF).
Note that due to queuing in the BTS there can still be a invalid
time period for immediate assignments, when the request is lingering
in the AGCH or PCH queues.
Sponsored-by: On-Waves ehf
|
|
Currently the CCCH flag is cleared and the PACCH flag is set when a
multislot upgrade is scheduled for a downlink TBF, even if the MS has
never confirmed in any way that the PACCH really exists. This can
happen if the MS did not receive the DL IMM.ASS. Since the CCCH flags
gets cleared in that case, the IMM.ASSS is never retried and all
subsequent PACKET DOWNLINK ASSIGNMENTS will fail.
This commit delays the update of these flags until the MS has
responded with a corresponding CONTROL ACK.
Sponsored-by: On-Waves ehf
|
|
Currently the old TFI is always used as ID when a
PACKET DOWNLINK ASSIGNMENT is generated. This fails
if the old TBF has not been fully assigned yet. The
MS will then ignore the PDA.
This commit changes write_packet_downlink_assignment to accept
an additional parameter old_tfi_is_valid and uses the new TBF's
TLLI instead of the olf TFI if that parameter is set to false.
Sponsored-by: On-Waves ehf
|
|
Currently the checks for and the actual polling is done in several
places by copy & paste of several lines of code. This hinders changes
of they polling is handled internally and also is likely source of
programming mistakes.
Separate this into a check_polling function, that checks whether
polling is possible and returns the FN and the RRBP to be used in
that case. Otherwise the cause is logged (LOGL_DEBUG) and a negative
error value is returned. There are no other side effect beside the
logging.
If the call is successful, the set_polling method can be used to
actually register the polling.
Extend the encoder functions' parameters lists by an rrbp parameter.
Sponsored-by: On-Waves ehf
|
|
Currently tbf->control_ts is used to look up an incoming poll
response. Since that may eventually change, poll timeouts could
theoretically happen in that case.
Store the real poll TS in tbf->poll_ts at all places where
tbf->poll_fn is set. Do not use tbf->control_ts to look up
outstanding polls.
Sponsored-by: On-Waves ehf
|
|
Currently there are some places where tbf->control_ts != ts is
evaluated to check, whether ts is a control slot.
Replace these expressions by tbf->is_control_ts(ts) which does
the same whitout exposing internal fields.
Sponsored-by: On-Waves ehf
|
|
Currently the checks in that function are based on the different
internal TS values of a TBF. It is assumed that they match the TS
that the current RTS refers to.
This commit adds a TS parameter to create_ul_ass, create_dl_ass,
and create_ul_ack to make this more explicit.
Sponsored-by: On-Waves ehf
|
|
Currently existing TBF can be reused after an MS has sent a RACH
request. Since the MS can be or most probably is in packet idle mode
in that case, the TBF are no longer usable even if they share the
PDCHs and the control TS with the new one.
There are occasional freezes where the MS does no longer react to
messages sent on the PACCH.
This change aborts all pending TBFs if a new TBF is or has been
established via RACH.
Sponsored-by: On-Waves ehf
|
|
Currently the is a release() function which takes care of
statistics and shutdown of properly finished TBFs, but which
cannot be used for aborted TBFs.
This commit add an abort() method which handles unacked RLC blocks
as lost and doesn't start a release timer. This method will be
invoked by tbf_free() for downlink TBF.
Sponsored-by: On-Waves ehf
|
|
Increment CTR_TBF_DL_ABORTED/CTR_TBF_UL_ABORTED if a TBF gets freed
that is still in state GPRS_RLCMAC_FLOW.
Sponsored-by: On-Waves ehf
|
|
Currently the window size is fixed to 64 even for EGPRS.
Support dynamic window sizes depending on the number of PDCH. The
WS can be set to b + f * N_PDCH. If the result is not valid according
to TS 44.060, Table 9.1.9.2.1, the value will be corrected to use the
next lower valid value (or 64).
The following VTY commands are added (config-pcu node):
window-size <0-1024> set base (b) value and leave f unchanged
window-size <0-1024> <0-256> set base (b) and factor (f)
Sponsored-by: On-Waves ehf
|
|
If the downlink BSSGP didn't contain a RA Capabilities IE, both
MS class values are 0. The phone will send valid RA Caps later on.
Currently in that case, the downlink TBF is not established
if EGPRS is enabled.
Just force egprs_ms_class to 1 if EGPRS (only) is enabled.
Sponsored-by: On-Waves ehf
|
|
Currently the plain 'egprs' command enables EGPRS but doesn't prevent
phones from being served in GPRS mode if they do not support EGPRS.
This involves complex frame allocation implementations in dynamic
mode, especially if 8PSK is being used. This is due to the inability
of non-EGPRS phone to decode 8PSK USF and ES/P altogether. Since
polling has a higher priority than USF, collisions will have to be
prevented by the PCU by never using an GPRS USF if it refers to a FN
that is already being used for polling.
This commit just disables mixed usage by ignoring GPRS-only request
if EGPRS is enabled.
The following VTY command (config-pcu node) is changed:
egprs -> egprs only
Sponsored-by: On-Waves ehf
|
|
This commit removes gprs_rlcmac_tbf::extract_tlli and
Decoding::tlli_from_ul_data.
Sponsored-by: On-Waves ehf
|
|
Currently GPRS is always used for downlink, which violates TS 44.060
(concurrent TBF must have the same mode).
Enable EGPRS mode for downlink if the EGPRS MS class is != 0 and
EGRPS has been enabled.
Note that EGPRS Ack/Nack handling is not yet implemented, so enabling
EGPRS will not work still. But we will now get EGPRS DL ACK/NACK
messages now from the MS.
Sponsored-by: On-Waves ehf
|
|
Add an use_egprs parameter to write_packet_downlink_assignment
and add the EGPRS related fields if it is set to true. The
window size is fixed at 64 blocks, link quality measurement
reports have been disabled, and the other optional fields are not
present.
Sponsored-by: On-Waves ehf
|
|
Currently the TBF and MS object use a plain integer value
(current_cs) to manage the coding scheme. This makes it difficult to
support the MCS schemes. GprsCodingScheme supports a partial ordering
of these values (CS and MCS) and provides safe increment and
decrement methods.
Use the GprsCodingScheme type instead of integer for cs fields and
variables. Add a 'mode' to GprsMs which can be set to either GPRS,
EGPRS, or EGPRS_GMSK which also set the initial values of
current_cs_ul/dl. Select the mode based on max_mcs_ul and max_mcs_dl.
Sponsored-by: On-Waves ehf
|
|
LListHead does basically the same like llist_pods, but more C++ish
and with type safety.
This commit turns the former list field of gprs_rlcmac_tbf into a
private field, provides accessors, moves the related code from
pcu_vty.c to pcu_vty_functions.cpp, and removes the llist_pods
type and related code.
Sponsored-by: On-Waves ehf
|
|
This function is similar to the show_ms function already present in
the target file. Since the TBF lists will be turned into LListHead
based lists, they will get an iteration function in
pcu_vty_functions.cpp, too.
Sponsored-by: On-Waves ehf
|
|
Currently casts from gprs_rlcmac_tbf to gprs_rlcmac_ul_tbf and
gprs_rlcmac_dl_tbf are done by using static_cast. This doesn't provide
protection against converting a gprs_rlcmac_ul_tbf pointer to a
gprs_rlcmac_dl_tbf pointer and vice versa.
This commit provides two functions as_ul_tbf and as_dl_tbf, that
behave similar like dynamic_cast but use the direction field instead
of RTTI.
Sponsored-by: On-Waves ehf
|
|
Currently the GPRS parameters are used, which is ok for the WS but
not for the SNS.
This commit uses RLC_EGPRS_SNS and RLC_EGPRS_MIN_WS for the window
configuration.
Sponsored-by: On-Waves ehf
|
|
Currently the EGPRS mode is enabled in setup_tbf depending on the
values of egprs_ms_class and bts->egprs_enabled (both must be != 0).
This makes it difficult to set different values (like window
parameters) depending on the direction.
This commit moved the initialisation part to tbf_alloc_ul_tbf und
just leaves the setting of the ms_class to setup_tbf.
Sponsored-by: On-Waves ehf
|
|
Currently the gprs_rlc_dl_window and gprs_rlc_ul_window do not have
constructors, but need to get initialized explicitly.
This commit adds constructors to both classes and removes explicit
external initialization code.
Sponsored-by: On-Waves ehf
|
|
Currently gprs_rlcmac_tbf::extract_tlli takes care of decoding and
the TBF update. These are really different things and doing the
decoding in extract_tlli makes EGPRS support more complex.
This commit moves the TBF state related part into a new method
gprs_rlcmac_tbf::set_tlli_from_ul.
Sponsored-by: On-Waves ehf
|
|
Enable the TBF to use EGPRS if the bts->egprs_enabled config variable
has been set via the VTY "egprs" command and if the MS has signaled a
EGPRS multislot class.
Tell the MS to use EGPRS if the condition above holds.
Note that this will cause the MS to use EGPRS RLC block formats for
further messages which are not yet understood by the PCU.
Sponsored-by: On-Waves ehf
|
|
Add an egprs_ms_class argument to the allocation functions and
set/pass it where necessary.
Sponsored-by: On-Waves ehf
|
|
Add the following methods to gprs_rlcmac_tbf:
- is_egprs_enabled
- enable_egprs
- disable_egprs
Also show the value of the flag in name() by displaying "EGPRS" if
it is set.
Sponsored-by: On-Waves ehf
|
|
Currently the Encoding::write_packet_uplink_assignment method only
supports the GPRS variant of the message.
This commit adds the missing EGPRS variant to the encoder.
Sponsored-by: On-Waves ehf
|
|
When a timeout has occured several times, the procedures handled by
poll_timeout are aborted. This happens when the number of repetitions
exceed N3105. Currently only the timeouts themselves are counted.
This commits adds counters that are incremented if a procedure has
really failed.
New counter:
- rlc.ass.failed: Count failing UL and DL assigments via PACCH
- rlc.ack.failed: Count failing DL Ack/Nack requests
Sponsored-by: On-Waves ehf
|
|
Currently reuse_tbf (partly) resets the old DL TBF and uses its PACCH
to establish a new DL TBF. The method can not be used with UL TBFs.
This commit replaces the reuse_tbf method into a
gprs_rlcmac_dl_tbf:release method which triggers the TBF's timer
based deletion (so that the TFI is still reserved for some time) and
a gprs_rlcmac_tbf::establish_dl_tbf_on_pacch which can establish DL
TBFs on existing PACCHs of either DL or UL TBFs.
Sponsored-by: On-Waves ehf
|
|
Currently when a second MS object has been created for an MS, because
the TLLI was not known yet, the will be detected in
gprs_rlcmac_tbf::extract_tlli and the two objects will be merged by
update_ms. But when the dl_tbf is moved from the old to the new
(second) MS object, the old MS object can get idle and be removed
before the object are merged. This can cause LLC frame loss when the
MS object is deleted immediately after getting idle (no timeout
configured).
This commit adds a guard to keep the MS object until extract_tlli has
been executed.
Sponsored-by: On-Waves ehf
|
|
This reverts commit e91bd3babd5c04a154f296607b401a5050dcba31.
That commit seems to cause hanging DL TBFs when there was a RACH
based UL TBF establishment while it that TBF is active. This could be
caused by the use of a different PDCH for the SBA.
Conflicts:
tests/tbf/TbfTest.cpp
tests/tbf/TbfTest.err
|
|
This commit adds the relevant frame number to the "poll timeout"
logging message. In addition, logging is added to the places where
poll_fn gets set.
The goal is to track down the source for frequent "poll timeout"
messages.
Sponsored-by: On-Waves ehf
|
|
Currently when allocating tbf_alloc_ul_tbf or tbf_alloc_dl_tbf
objects, the allocated memory area is pre-initialised by talloc_zero
before the C++ constructors are called. This is not recognised by
Coverity, since there is no talloc model file yet. Thus Coverity
complains about missing initialisers.
On the other hand, it is still planned to convert the TBF classes
into real C++ ones. So instead of silencing Coverity directly, this
is an opportunity to do it the C++ way.
This commit adds initialisers and initialisation code for all
members that relied on talloc_zero. The corresponding calls to
talloc_zero are replaced by calls to talloc to give ASAN/valgrind
a chance to detect future initialisation errors. Some initialisation
code is also moved from setup_tbf to the constructors, notably the
initialisation of the bts pointer.
Fixes: Coverity CID 1320604, 1320605, 1320606
Sponsored-by: On-Waves ehf
|
|
Currently when calling GprsMs::attach_tbf and a TBF of the same
direction already exists, the old TBF gets detached from the MS
object.
Therefore that TBF object loses access to that MS object including
for instance TLLI and IMSI.
This leads to failing DL TBF reuses, since the downlink assigment
cannot be sent on the PACCH later on because that must be sent on the
old DL TBF which ms() is NULL and the new DL TBF cannot be retrieved.
This commit fixes this bug by changing the GprsMs implementation to
keep a list of replaced (old) TBFs. TBFs are only removed when they
are being detached explicitely (see tbf_free and set_ms).
Addresses:
tbf.cpp:741 We have a schedule for downlink assignment at uplink
TBF(TFI=1 TLLI=0xf35a680e DIR=UL STATE=RELEASING), but there is no
downlink TBF
Sponsored-by: On-Waves ehf
|
|
The TBF object are currently created by using talloc_zero/talloc_free
directly from plain functions. Therefore C++ constructors and destructors
are not called. So the only initialisation that is done is setting
every member to 0. Non POD members do not have their constructors
called either, which makes it impossible to use the current LListHead
class for real members when the LListHead::m_back member has to be set.
This commit changes the TBF allocation functions to call the
corresponding C++ constructor after the call to talloc_zero and to
register the C++ destructor with the talloc context, so that is is
called before talloc_free actually frees the memory.
With this change, non-POD members and custom
constructors/desctructors can be used with gprs_rlcmac_tbf,
gprs_rlcmac_dl_tbf, and gprs_rlcmac_ul_tbf.
Note that this change is only a single step of the plan to turn the
TBF classes into real C++ classes.
Sponsored-by: On-Waves ehf
|