| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2675 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Move them out of the interface file - primarily for
readability.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2674 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Move push and pull of buffers into a dedicated file. This will
allow us to swap out resampling, non-resampling, and possibly
floating point device interfaces while presenting a single
floating point abstration in the interface itself.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2670 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Remove radio clock and vector interfaces into their own
files. This clears up and simplifies the radio interface
and, additionaly, prepares for a further split of the I/O
portion for optional resampler use.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2669 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
These lines are virtually never enabled.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2666 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
This patch fixes some confusion in gain vs. attenuation
setting. The UHD device is controlled through gain
settings but OpenBTS represents gain in terms of
attenuation relative to maximum - 0 dB attenuation.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2662 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Commit e161523c (transceiver: simplify transmit power control)
changed transmit gain control to RF setting only. This was
appropriate for a WBX board with 25 dB of gain control, but
inappropriate for an RFX with fixed transmit gain.
RFX boards will regain the ability to set transmit
attenuation. Since gain is set on the RF side first,
reintroducing digital gain settings should have limited
overall effect on non-RFX daughterboards.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2660 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
UHD will internally accept floats with a range of +/-1.0,
which corresponds to a 16-bit signed integer range of
apporximately +/- 32000. Set the default amplitude to .3,
which is a safe value agaist saturation elsewhere in the
transmit chain.
The non-UHD maximum amplitude is unchanged at 13500.
Remove digital gain control because it's unnecessary and
causes extra load on enbedded systems.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2654 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
The output of the modulator or resampler is scaled and
converted from floating point to fixed point. The scaling
factor is the leftover dB in RF attention (relative to max
transmit power), which is handled prior to the integer
conversion. This should work across all daughterboards and
non-UHD installations.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2650 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Previously this was referenced off the the ad9862
PGA with a range from 0 to -20 dB. Instead base
the attenuation factor on the maximum total RF
gain returned by the device.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2649 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
'loadTest' variable was never initialized sometimes causing
segmentation fault on transceiver startup.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2631 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2307 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
