Age | Commit message (Collapse) | Author | Files | Lines |
|
Allow setting the device to non single SPS sample rates - mainly
running at 4 SPS as the signal processing library does not support
other rates. Wider bandwith support is required on the receive path
to avoid 8-PSK bandlimiting distortion for EDGE.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
|
|
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
|
|
Commit 8e17df7374367d57 "Add option for baseband frequency offset",
modified the base device API to allow for RF tuning, which was never
updated for the USRP1.
Update the implementation to match the API, however, note actual offset
in the USRP1 remains unsupported.
Signed-off-by: Tom Tsou <tom@tsou.cc>
|
|
This patch add support for dual channel diversity on the receive
path. This allows two antennas two shared antennas to be used for
each ARFCN handling channel in the receiver. This configuration
may improvde performance in multi-path fading environments,
however, noise andpotential interference levels are increased due
to the higher bandwidth used.
The receive path is oversampled by a factor of four for a rate
of 1.083333 Msps. If the receive paths are tuned within a
maximum channel spacing (currently set at 600 kHz), then both
ARFCN frequencies are processed by each channel of the receiver.
Otherwise, the frequency shifted diversity path is disabled and
standard non-diversity operation takes place.
Diversity processing is handled by selecting the path with the
higheset energy level and discarding the burst on the second
path. Selection occurs on a burst-by-burst basis.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This patch primarily addresses devices with multiple RF front end
support. Currently device support is limited to UmTRX.
Vectorize transceiver variables to allow multiple asynchronous
threads on the upper layer with single downlink and uplink threads
driving the UHD I/O interface synchronously.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Enabling the external reference on UHD devices through the configure
time switch is awkward. Use a database variable "TRX.Reference" with
'0' or '1' value for internal and external references respectively.
Use internal reference is no entry is defined.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Current functionality with these old versions is questionable.
There is no reason to use any version of GNU Radio / libusrp older
than 3.3. Version 3.4.2 is the only recommended version for USRP1
users.
Non-USRP1 users must use UHD driver from Ettus Research.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This patch applies oversampling, when selected with 4 sps,
to the downlink only, while running the receiver with
minimal sampling at 1 sps. These split sample rates allow
us to run a highly accurate downlink signal with minimal
distortion, while keeping receive path channel filtering
on the FPGA.
Without this patch, we oversample the receive path and
require a steep receive filter to get similar adjacent
channel suppression as the FPGA halfband / CIC filter
combination, which comes with a high computational cost.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Remove the built time resampling selection and link both options.
Move the normal push/pullBuffer() calls back to the base class and
overload them in the inherited resampling class.
USRP2/N2xx devices are the only devices that require resampling so
return that resampling is necessary on the device open(), which is
the point at which the device type will be known.
The GSM transceiver only operates at a whole number multiple of
the GSM rate and doesn't care about the actual device rate and
if resampling is used. Therefore GSM specific portion of the
transceiver should only need to submit the samples-per-symbol
value to the device interface.
Then, the device should be able to determine the appropriate
sample rate (400 ksps or 270.833 ksps) and if resampling is
appropriate.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
UHD accepts optional 'args' that can be used for device descriptions
such as IP address, device type, etc. Allow these to be passed in on
the transceiver command line as the third argument (number of supported
carriers is the second argument). This option benefits those who may
have multiple UHD devices attached to a single system.
This option is not yet supported by GSM core and requires starting the
transceiver independently on the command line. This option has no
effect when USRP1 is used.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@4315 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Transmit gain setting would deceptively set the receive
gain instead. Since transmit attenuation is a combination
of RF gain and digital scaling, this major copy/paste bug
may have gone unnoticed by many users.
Reported-by: Robin Coxe <coxe@close-haul.com>
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@3309 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Device errors regarding properties such as sample
rate or frequency tuning are almost always fatal and
lead to the common error "assuming TRX is dead".
Make sure that these errors are clearly presented to
the user.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2700 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
The following option selects single daughterboard use on
side A only. Otherwise, the default setting is TX on A and
Rx on B.
./configure --with-singledb
Other options are possible, as per the following enum, but
for simplicity with configure options, there are only two
choices.
enum dboardConfigType {
TXA_RXB,
TXB_RXA,
TXA_RXA,
TXB_RXB
};
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2687 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Log level changes in P2.8:
ERROR -> ERR
WARN -> WARNING
DEEPDEBUG -> DEBUG
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2683 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Transmit tuning was primarily setup for side A only. Some boards
- WBX - would still tune with improper channel arguments, though
receiver performance was disrupted.
Previous testing was primarily with single board on side A only
or dual configuration with side A transmit, so this bug largely
went undetected. Patch tested with RFX and WBX daughterboards
in single and dual configurations sides A and B.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2658 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2657 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
These are mostly identical changes as added to the non-52MHz
implementation with the exception of sample rate.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2634 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Remove all RFX specific parts and control daughterboard
functionality using the base API. The tuning is now set
to a non-inverted image so remove the I/Q swap as well.
Daughterboard configuration is set through an enum
variable. Currently, there is no auto-configuration and
the default is Tx/RX on sides A/B respectively. For
transceiver boards the receive antenna is set to RX2.
enum dboardConfigType {
TXA_RXB,
TXB_RXA,
TXA_RXA,
TXB_RXB
};
const dboardConfigType dboardConfig = TXA_RXB;
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2632 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2424 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2342 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2307 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|