Age | Commit message (Collapse) | Author | Files | Lines |
|
This includes unknown and unused variables, functions, and
non-relevant documentation.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
We support one TSC value per each transceiver object. Only channel
zero can set this value. Other channels can attempt to set the TSC
value, but will error if the TSC does not match the existing value.
In either case, non-zero channels do not manipulate the gloabl TSC
setting.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Simply vectorize the existing power state variable.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Pointer accessor and noise average methods for radio and noise vectors
respectively.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Each ARFCN channel may be independently configureted and possibly on
separate hardware, so don't share a single vector for noise estimate
calculations. Allow a non-pointer based iterator so we can get away
with using the default copy constructor.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
The transceiver has the ability to detect bursts below the noise floor,
but little hope in successful decoding, so don't even try. We still use
the detected burst to differentiate against noise vs actual data.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
In errant cases, GSM core may send bursts with invalid slot values,
which is allowed by the GSM::Time object. If we find a burst like this
coming into the transceiver, then drop it immediately.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This patch add support for dual channel diversity on the receive
path. This allows two antennas two shared antennas to be used for
each ARFCN handling channel in the receiver. This configuration
may improvde performance in multi-path fading environments,
however, noise andpotential interference levels are increased due
to the higher bandwidth used.
The receive path is oversampled by a factor of four for a rate
of 1.083333 Msps. If the receive paths are tuned within a
maximum channel spacing (currently set at 600 kHz), then both
ARFCN frequencies are processed by each channel of the receiver.
Otherwise, the frequency shifted diversity path is disabled and
standard non-diversity operation takes place.
Diversity processing is handled by selecting the path with the
higheset energy level and discarding the burst on the second
path. Selection occurs on a burst-by-burst basis.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Separate the large pullRadioVector() call, which forms the central
portion of the receive path burst processing. Break out RACH, normal
burst, and demodulation into separate methods. This makes the burst
handling from the FIFO read to soft bit output somewhat more
manageable.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
The call into table lookup will loop on values outside of the
table range. With continuously increasing phase, this leads
to an eventual permanent hard spin. Wrap the phase value to
prevent that from happening.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
As we add more channel combintions including but not limited to
new devices, signal processing schemes, and diversity, we'll
need to handle more special cases. Add string descriptions for
just a bit more sanity.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This patch allows multiple signalVectors to be stored within
a single radioVector object. The motivation is to provide
a facility for diversity and/or MIMO burst handling. When
no channel value is specified, single channel bevhaviour
is maintained.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Style change for clarity only.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Stack allocating the correlation output generates a call to the copy
constructor of an zero valued vector. We can avoid this extra copy
constructor with a pointer reference and dynamic allocation.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Allow non-in-place use of the delay setting. Internally, the delay call
creates a new vector and copies the contents back into the original.
Instead, provide the option to return the computed output vector
directly and remove an an extra copy in the process.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
On Beagle Board the call into the sinc() function is generating a lot of
load on the peak interpolation. Simplify the sinc() function with a
dedicated table lookup. Eventually, this table may be removed in favour
of using a precomputed filterbank for fractional delay determination.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Set a transceiver high level length value that specifies the largest
number of complex or real filter taps that we will encounter. This
allows preallocation of head room and prevents an extra allocation and
copy on every incoming receive burst.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
With testing on current UHD releases, currently 003.005.xxx series,
timeout errors on both receive and transmit are recoverable on network
and USB based devices. Remove the fatal error conditions.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Clock indications passed up to GSM core originate on the transciever
downlink side. Set priority to keep the flow of clock updates
consistent.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This includes ARM Cortex A8 and A15 powered device such as Beagle
Board, Gumstix driven E100 USRP, and Arndale board. Set the reduced
SPS value automatically for the user.
For x86, if we don't support SSE3, then the architecture is
probably ancient and not with using. Drop the sampling down anyways
to at least make an attempt. Non floating point SIMD devices (e.g.
Raspberry Pi) also fall in this category
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Preallocate and compute a bank of fractional sample delay filters.
The number of filters to allocate is specified by the DELAYFILTS
preprocessor definition with a default value of 64. The filters
themselves are sinc pulse generated with 20 taps and Blackman-harris
windowed .
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Break out the signalVector object and clean up the interface in the
process.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Currently the code allocations a signalVector and then copies
into a radioVector. This is unnecessary because the latter is
a derived class making the first allocation unnecessary.
Modify the radioVector constructor to allow direct use in the
case above.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This prevents the use of a copy constructor in the downlink
modulator and prevents a secondary memory allocation during
the convolution. Avoid both cases by dynamically allocating
with preloaded head room. The latter provides enough memory
before the first sample in the burst to cover the length
of the filter taps.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Complex-complex block multiples are used for phase rotation of
bursts. Optimization targeted from perf profiling.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
B2xx is a USB based device so use the USRP1 based adaptive flow
control window for transmit bursts. This adds additional stability
primarily on ARM platforms.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
The transceiver and underlying device drivers are threaded. use
the following priority levels.
0.50 - UHD driver internal threads
0.45 - Receive device drive thread
0.44 - Transmit device drive thread
0.43 - UHD asynchronous update thread (error reporting)
0.42 - Receive burst processing thread(s)
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Similar to the existing Intel SSE cases, add support for NEON vector
floating point SIMD processing. In this case, use ARM assembly
directly as the NEON intrinsics do not generate preferential code
output.
Currently support NEON vectorized convolution and floating point
integer conversions.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This patch primarily addresses devices with multiple RF front end
support. Currently device support is limited to UmTRX.
Vectorize transceiver variables to allow multiple asynchronous
threads on the upper layer with single downlink and uplink threads
driving the UHD I/O interface synchronously.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
There is no need to create this method. Just call the UHD interface
directly.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
USRPping and sigProcLibTest are in an unmaintained state,
while the intended functionality remains unknown. Stored
filter taps are also unused and should also be removed.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Collect the slot information into an indpendent state object. This
will allow us to easily create multiple instances of internal state
variables without having to replicate the transceiver object itself.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
For multiple transceiver connections, it is inappropriate to
allocate all sockets in the transceiver constructor due to not
knowing how many connections are avaialble in advance and for
error checking purposes. Instead, store the base socket address
port combination and setup the sockets in the initialization
call.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
The current status and operability of this compile option is
unknown. Remove due to lack of use, demand, and maintenance.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
We do not use subversion. We do not need to refer to subversion
reference numbers.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Underruns are only explicitly set on the downlink side. Overruns
are logged but unused. In either case, reset indicators to false
to avoid sending false state information.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Using non-SSE4.1 enabled architecture would cause undefined
reference to 'convert_si16_ps' call.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Currently the default configuration is to not build the full
transceiver, which is pointless. Set the UHD driver, which
includes either Ettus or Fairwaves variants, as the default.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Move x86 specific files into their own directory as this
area is about to get crowded with the addition of ARM
support.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Use the same measurement method for RSSI as the noise level. Previous
method was to use the peak correlation amplitude relative to the
expected value. This created two very different amplitude approaches
between the noise measurement and RSSI measurement, which would
throw off the upper layer MS power control loop.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Previous removal of the energy detector requirement broke
the noise level calculation loop. The previous adaptive
approach was finicky - noticably at high gain levels. Since
we no longer use the energy threshold for primary burst gating,
we can return to a simpler world.
In the new approach, we compute a running average of energy
levels and track them with a noise vector. A timeslot that
passes the correlator threshold is a valid burst. These are
not used in the noise calculation. Everything else is
considered noise and used to compute the noise level with
respect to full scale input level, which for almost all
supported devices is 2^15.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Enabling the external reference on UHD devices through the configure
time switch is awkward. Use a database variable "TRX.Reference" with
'0' or '1' value for internal and external references respectively.
Use internal reference is no entry is defined.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
We want to push UHD logs to the OpenBTS logging system, but most
device errors occur at startup, so keep the output on stdout until
after device initialization. That way obvious errors are easily
viewable before seeing the useless TRX timeout message.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This primarily addresses the error case at initialization.
In the event that the transceiver fails to start, we should
be able cleanly shutdown and release while providing a useful
reason for exiting.
After the radio is started and threads launched, there
are no thread state variables or shutdown messaging between
threads, and the transceiver cannot be consistently
shutdown. This issue remains to be solved.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Previous send and receive buffers at the radio interface were
arbitrarily set to a sufficient size. For normal (non-resampling)
devices, use a block (chunk) size of 625 samples. For 64 or 100
MHz resampling devices, use 4 times the reduced resampling
numerator or denominator and provide bounds checking where
appropriate.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Move B100 to the resampling interface with default
clocking. This temporarily resolves undetermined
FPGA clocking issues. This also provides extensible
support for multiple clocking rates and resampling
ratios.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Current functionality with these old versions is questionable.
There is no reason to use any version of GNU Radio / libusrp older
than 3.3. Version 3.4.2 is the only recommended version for USRP1
users.
Non-USRP1 users must use UHD driver from Ettus Research.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Identical to B200 support, but explicitly check for the device type
name.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This patch applies oversampling, when selected with 4 sps,
to the downlink only, while running the receiver with
minimal sampling at 1 sps. These split sample rates allow
us to run a highly accurate downlink signal with minimal
distortion, while keeping receive path channel filtering
on the FPGA.
Without this patch, we oversample the receive path and
require a steep receive filter to get similar adjacent
channel suppression as the FPGA halfband / CIC filter
combination, which comes with a high computational cost.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This requires an additional memcpy() on the signal vector
constructor, but allows the interpolation filter to use
SSE optimzationed convolution.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|