aboutsummaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2015-05-19Transceier52M: Make error response to an unknown command on UDP command ↵fairwaves/master-oldAlexander Chemeris1-0/+1
interface more understandable. Previously we just repeated the last response which could confuse a command sender.
2015-05-19Transceiver: Check TSC values to be in [0..7] range.Alexander Chemeris1-3/+4
2015-05-17uhd: Output Rx/Tx gain limits to log to make it more transparent.Alexander Chemeris1-4/+10
2015-05-14Transceiver52M: Add clipping detection on RACH inputTom Tsou3-5/+38
Alert user of overdriven RACH input indicated by a positive threshold detector result. This indication serves as notification that the receive RF gain level is too high for the configured transceiver setup. Signed-off-by: Tom Tsou <tom@tsou.cc>
2015-05-08A hack to pass all dev.args to UHD.Alexander Chemeris1-1/+1
2015-05-07umtrx: Don't use DSP tuning, because LMS6002D PLL steps are small enough.Alexander Chemeris1-1/+13
We end up with DSP tuning just for 2-3Hz, which is meaningless and only distort the signal.
2015-05-07uhd: Update UmTRX specific code to work with PA Tx gain.Alexander Chemeris1-2/+3
2015-05-07uhd: Set RF frontend bandwidth for UmTRX to improve signal quality.Alexander Chemeris1-0/+10
2015-04-29debian: make it possible to install osmo-trx dependencies manually on the systemIvan Kluchnikov1-0/+3
2015-04-28Revert "UmTRX: Fix Tx gain setting procedure for the best signal quality."Alexander Chemeris1-12/+22
This reverts commit 48da6f97e3274f751a133365b526f4ca0f3b7ea1.
2015-03-25uhd: Use full DAC scale with UmTRX to improve signal quality.Alexander Chemeris1-2/+3
2015-03-01Logger: Output ERR log messages to stderr as well.Alexander Chemeris1-1/+1
2015-02-23debian: update osmo-trx dependenciesIvan Kluchnikov1-1/+1
Now we use uhd and umtrx-uhd instead of libuhd-dev.
2014-12-16Handover support for transceiver (TCH/F TCH/H SDCCH4 SDCCH8)Ivan Kluchnikov2-0/+39
It allows to enable/disable access burst detection on each subslot individually.
2014-09-26UmTRX: Fix Tx gain setting procedure for the best signal quality.Ivan Kluchnikov1-22/+12
We fixed setting Tx gain procedure in UHD, so we should fix it in osmo-trx too. From our measurements, VGA1 must be 18dB plus-minus one and VGA2 is the best when 23dB or lower.
2014-09-22debian: Add debug package for the osmo-trxIvan Kluchnikov5-6/+15
2014-09-22debian: Add debian directory to ease building packagesIvan Kluchnikov6-0/+58
2014-09-22Transceiver52M: UHD: Exit on receive more than 100 timeout errorsIvan Kluchnikov1-0/+6
Receiving timeout is not a fatal error and should be recoverable on network devices. But for some reasons these errors are not always recoverable, in this case osmo-trx should be restarted.
2014-09-22UmTRX: Manually set Tx gain stages for the best signal quality.Alexander Chemeris1-5/+39
New UHD versions support split configuration of Tx gain stages. We utilize this to set the gain configuration, optimal for the Tx signal quality. From our measurements, VGA1 must be 18dB plus-minus one and VGA2 is the best when 23dB or lower.
2014-05-08Transceiver52M: Fix SSE convolution shuffle registerThomas Tsou1-1/+1
An errant shuffle register value used in complex-complex convolution causes distorted correlation peak-to-average values for certain TSC values. The error effect varies for different TSC sequences with the most noticeable effect of degraded detection on TSC 1 and no effect on TSC 7. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2014-04-15Transceiver52M: Fix retransmissions when filler table is enabledThomas Tsou1-0/+4
Commit 15d743efaf8d3ec8dacd37fbac434c1e719c0b30 "Disable filler table retransmissions by default" made OpenBTS style filler table behavior optional. When enabled, dummy bursts were automatically loaded into the filler table, but the table was not updated and only filler busts were retransmitted. Enable the restransmit state flag when the filler table option is specified. Only preload filler table and enable retransmissions on channel zero. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2014-04-09Transceiver52M: Add E1XX USRP device id and timingsThomas Tsou1-2/+21
Device specific timing settings for the E100 and E110 were missing from the Tx/Rx offset table. Add E1XX identifier and offsets to the device list and offset table respectively. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2014-03-27Transceiver52M: Allow startup delay for stream alignmentThomas Tsou1-5/+11
UHD requires a small amount of time to align multiple streams at startup. Delay the startup by 100 ms relative to the queried device time (actual delay inclusive of control latencies will be less). The following error is only relevant to dual-channel UHD devices (e.g. Fairwaves UmTRX and Ettus B210). UHD Error: The receive packet handler failed to time-align packets. 1002 received packets were processed by the handler. However, a timestamp match could not be determined. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2014-03-27Transceiver52M: Set UHD rates before creating streamersThomas Tsou1-12/+12
Recent versions of UHD require setting the sample rate before creating streamers otherwise the following exception occurs. Boost_105300; UHD_003.007.000-0-g7fef199d terminate called after throwing an instance of 'boost::exception_detail::clone_impl<boost::exception_detail::error_info_injector<boost::math::rounding_error> >' what(): Error in function boost::math::round<d>(d): Value -nan can not be represented in the target integer type. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2014-03-06Transceivert52M: Add option for baseband frequency offsetThomas Tsou3-13/+28
Allow command line setting of the DSP frequency in UHD. All channels will be tuned with the same offset. Dual-channel tuning with the B210, which uses a single LO, will override the command line offset value and set the DSP frequency automatically. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2014-03-03Transceiver52M: Enable B210 dual channel supportThomas Tsou1-12/+89
The main difference between existing UmTRX dual channel is the single LO on B210 transmit and receive front-ends vs. independent tuning paths. In order to support dual-ARFCN frequencies, baseband offset conversion must be applied by tuning the FPGA CORDIC for each channel. For B210, the following tuning order is applied. 1. If the new frequency of channel A is within the baseband range of channel B, then retune both channels with the RF centered and equal valued positive and negative baseband shifts. 2. If the new frequency of channel A is not with the baseband range of channel B, then retune channel A directly (without manual applied offset). Channel B will no longer be tuned to the previous frequency. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2014-03-03Transceiver52M: Disable initial device time resetThomas Tsou2-21/+31
With dual-channels on B210, we lose the ability to reset both channels to a synchronized state. Instead, let the timestamp clock start with an arbitary value, which is the first timestamp received from the device, instead of a near-zero value. This approach also makes integration for device, in general, with free-running timestamp clocks. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2014-03-03Transceiver52M: Split B200 and B210 identifiersThomas Tsou1-7/+13
Differentiate between the two in order to provide enumeration for dual-channel support. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2014-02-13Transceiver52M: Set B2XX clock frequency to 26 MHzThomas Tsou1-1/+1
Change from the original USRP1 rate of 52 MHz. On B2XX we can use 26 MHz, which is closer to the default 32 MHz of the device. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2014-01-26Transceiver52M: Disable filler table retransmissions by defaultThomas Tsou3-23/+60
Burst selection at a particular time works in the following order of priority. 1. Slot is disabled with channel combination set to NONE (default) 1. Burst exists in priority queue for the current time. 2. Filler table entry is used This patch sets default behaviour to force all filler table entries to zero and disallows filler table changes. This effectively means that only bursts received from upper layers will be transmitted and nothing will be automatically transmitted in the absence or delay of incoming burts at a particular time. New Command line option "Enable C0 filler table" allows reverting to previous idle burst generation and retransmission behaviour on TRX0. Retransmission cannot be enabled on non-C0 channels. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-18Transceiver52M: Add missing scaling vector resizeThomas Tsou1-0/+1
Downlink scaling factors, which are stored in a vector for multiple channels, was not being sized correctly. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-17Transceiver52M: Remove database configuration file requirementThomas Tsou1-31/+14
We don't require any parameters stored in the configuration table, so don't bother with the existence of the persistent database file. This also removes an unnecessary step during initial setup since relevant parameters can be configured from the command line. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-16Transceiver52M: Ignore channel estimation if we are not equalizingThomas Tsou1-1/+1
Equalization is currently disabled by default. As such, we don't need to run channel estimates or even track the update state, which would otherwise be allocating/decallocating the channel state vector at regular intervals. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-16Transceiver52M: UHD: Check running status before stopping streamThomas Tsou1-1/+4
On startup errors we get a segfault if we stop and shutdown. This is because we try to send a stop stream command to the device before it has been created. Setup a check for running status before attempting to stop the physical device. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-16Transceiver52M: Create new osmo-trx executableThomas Tsou4-237/+420
Create new main executable with full command line option parsing of relevant parameters. Database configuration table still exists (and must exist because of the global gConfig object), but can be bypassed with command line options. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-16Transceiver52M: Output device and operating mode to stdoutThomas Tsou1-12/+17
Very useful user information at startup. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Enable all warnings and resolveThomas Tsou8-17/+17
Mainly basic signed vs unsigned comparisons and intializer ordering. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Add virtual destructor for radio deviceThomas Tsou1-0/+2
Empty destructor removes compile warning. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Remove unused codeThomas Tsou6-68/+3
This includes unknown and unused variables, functions, and non-relevant documentation. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Allow only channel zero to set TSC valueThomas Tsou1-3/+5
We support one TSC value per each transceiver object. Only channel zero can set this value. Other channels can attempt to set the TSC value, but will error if the TSC does not match the existing value. In either case, non-zero channels do not manipulate the gloabl TSC setting. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Use independent power scaling varables for each channelThomas Tsou4-22/+20
Simply vectorize the existing power state variable. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Set const qualifier on appropriate radio vector methodsThomas Tsou2-4/+4
Pointer accessor and noise average methods for radio and noise vectors respectively. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Use independent noise vectors for each channelThomas Tsou4-24/+27
Each ARFCN channel may be independently configureted and possibly on separate hardware, so don't share a single vector for noise estimate calculations. Allow a non-pointer based iterator so we can get away with using the default copy constructor. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Ignore detected bursts at the noise floorThomas Tsou1-4/+5
The transceiver has the ability to detect bursts below the noise floor, but little hope in successful decoding, so don't even try. We still use the detected burst to differentiate against noise vs actual data. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Check time slot validity of incoming burstsThomas Tsou1-0/+5
In errant cases, GSM core may send bursts with invalid slot values, which is allowed by the GSM::Time object. If we find a burst like this coming into the transceiver, then drop it immediately. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Add dual channel diversity receiver optionThomas Tsou11-50/+390
This patch add support for dual channel diversity on the receive path. This allows two antennas two shared antennas to be used for each ARFCN handling channel in the receiver. This configuration may improvde performance in multi-path fading environments, however, noise andpotential interference levels are increased due to the higher bandwidth used. The receive path is oversampled by a factor of four for a rate of 1.083333 Msps. If the receive paths are tuned within a maximum channel spacing (currently set at 600 kHz), then both ARFCN frequencies are processed by each channel of the receiver. Otherwise, the frequency shifted diversity path is disabled and standard non-diversity operation takes place. Diversity processing is handled by selecting the path with the higheset energy level and discarding the burst on the second path. Selection occurs on a burst-by-burst basis. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Refactor receive path outer burst handlingThomas Tsou2-95/+141
Separate the large pullRadioVector() call, which forms the central portion of the receive path burst processing. Break out RACH, normal burst, and demodulation into separate methods. This makes the burst handling from the FIFO read to soft bit output somewhat more manageable. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: sigproc: Wrap internal phase on frequency shiftThomas Tsou1-0/+4
The call into table lookup will loop on values outside of the table range. With continuously increasing phase, this leads to an eventual permanent hard spin. Wrap the phase value to prevent that from happening. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: UHD: Add string descriptors to device-offset pairsThomas Tsou1-10/+11
As we add more channel combintions including but not limited to new devices, signal processing schemes, and diversity, we'll need to handle more special cases. Add string descriptions for just a bit more sanity. Signed-off-by: Thomas Tsou <tom@tsou.cc>
2013-11-15Transceiver52M: Add vectorized radio burst capabilityThomas Tsou5-26/+62
This patch allows multiple signalVectors to be stored within a single radioVector object. The motivation is to provide a facility for diversity and/or MIMO burst handling. When no channel value is specified, single channel bevhaviour is maintained. Signed-off-by: Thomas Tsou <tom@tsou.cc>