blob: 8c6712e1c4266d21771b1abbf684336b12430a26 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
|
TETRA MAC/PHY layer experimentation code
(C) 2010-2011 by Harald Welte <laforge@gnumonks.org>
======================================================================
This code aims to implement the sending and receiving part of the
TETRA MAC/PHY layer.
If you read the ETSI EN 300 392-2 (TETRA V+D Air Interface), you will
find this code implementing the parts between the MAC-blocks (called
type-1 bits) and the bits that go to the DQPSK-modulator (type-5 bits).
It is most useful to look at Figure 8.5, 8.6, 9.3 and 19.12 in conjunction
with this program.
You will need libosmocore (http://bb.osmocom.org/trac/wiki/libosmocore) to link.
== Demodulator ==
src/demod/python/cpsk.py
* contains a gnuradio based pi4/DQPSK demodulator, courtesy of KA1RBI
src/demod/python/tetra-demod.py
* call demodulator on a 'cfile' containing complex baseband samples
src/demod/python/usrp1-tetra_demod.py
* use demodulator in realtime with a USRP1 SDR
src/demod/python/usrp2-tetra_demod.py
* use demodulator in realtime with a USRP2 SDR
The output of the demodulator is a file containing one float value for each symbol,
containing the phase shift (in units of pi/4) relative to the previous symbol.
You can use the "float_to_bits" program to convert the float values to unpacked
bits, i.e. 1-bit-per-byte
== PHY/MAC layer ==
=== library code ===
Specifically, it implements:
lower_mac/crc_simple.[ch]
* CRC16-CCITT (currently defunct/broken as we need it for
non-octet-aligned bitfields)
lower_mac/tetra_conv_enc.[ch]
* 16-state Rate-Compatible Punctured Convolutional (RCPC) coder
lower_mac/tetra_interleave.[ch]
* Block interleaving (over a single block only)
lower_mac/tetra_rm3014.[ch]
* (30, 14) Reed-Muller code for the ACCH (broadcast block of
each downlink burst)
lower_mac/tetra_scramb.[ch]
* Scrambling
lower_mac/viterbi*.[ch]
* Convolutional decoder for signalling and voice channels
phy/tetra_burst.[ch]
* Routines to encode continuous normal and sync bursts
phy/tetra_burst_sync.[ch]
=== Receiver Program ===
The main receiver program 'tetra-rx' expects an input file containing a
stream of unpacked bits, i.e. 1-bit-per-byte.
=== Transmitter Program ===
The main program conv_enc_test.c generates a single continuous downlinc sync
burst (SB), contining:
* a SYNC-PDU as block 1
* a ACCESS-ASSIGN PDU as broadcast block
* a SYSINFO-PDU as block 2
Scrambling is set to 0 (no scrambling) for all elements of the burst.
It does not actually modulate and/or transmit yet.
== Quick example ==
# assuming you have generated a file samples.cfile at a sample rate of
# 195.312kHz (100MHz/512 == USRP2 at decimation 512)
src/demod/python/tetra-demod.py -i /tmp/samples.cfile -o /tmp/out.float -s 195312 -c 0
src/float_to_bits /tmp/out.float /tmp/out.bits
src/tetra-rx /tmp/out.bits
|
