blob: c9de19aa992da7f51ebf7a429e24269a5d081844 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
|
<vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'>
<node id='21'>
<child_of nodeid='4' />
<name>SGSN Configuration Node</name>
<description>Configure the remote GGSN, access-control and other
attributes of the SGSN</description>
<command id='gtp local-ip A.B.C.D'>
<description>
Configure the local IP address to which the SGSN should
bind for the Gp interface (towards the GGSNs).
Please note that in case you would like to run the GGSN
on the same machine as the SGSN, you can not run both on
the same IP address. It is suggested to use 127.0.0.1
for the SGSN and 127.0.0.2 for the GGSN in such
situations.
</description>
</command>
<command id='ggsn <0-255> remote-ip A.B.C.D'>
<description>
Configure a static GGSN with a given numeric identifier
to use the specified remote IP address.
</description>
</command>
<command id='ggsn <0-255> gtp-version (0|1)'>
<description>
Configure whether to use GTPv0 or GTPv1 towards the
specified GSSN number.
</description>
</command>
<command id='ggsn dynamic'>
<description>
Enable dynamic resolving of GGSNs based on DNS resolving
the APN name like in a GRX-style setup. Changing this
setting requires a re-start of the SGSN.
</description>
</command>
<command id='grx-dns-add A.B.C.D'>
<description>
Use the specified IP address for DNS-resolving the AP
names to GGSN IP addresses
</description>
</command>
<command id='apn APNAME ggsn <0-255>'>
<description>
Map the given APN Name to the given GGSN number.
</description>
</command>
<command id='apn APNAME imsi-prefx IMSIPRE ggsn <0-255>'>
<description>
Map the given APN Name to the given GGSN number _only_
if the IMSI matches the given prefix.
</description>
</command>
<command id='imsi-acl (add|del) IMSI'>
<description>
Add or delete the given IMSI to/from the global Access
Control List.
</description>
</command>
<command id='auth-policy (accept-all|closed|acl-only|remote)'>
<description>
Configure the Authorization policy of the SGSN. This
setting determines which subscribers are permitted to
register to the network.
</description>
</command>
<command id='gsup remote-ip A.B.C.D'>
<description>
Set the IP address of the HLR (gateway) for the GSUP protocol.
This setting only applies if auth-policy remote is used.
</description>
</command>
<command id='gsup oap-id <0-65535>'>
<description>
Set the OAP client ID for authentication on the GSUP
protocol.
This setting only applies if auth-policy remote is used.
</description>
</command>
<command id='gsup oap-k K'>
<description>
Set the OAP shared secret key K for authentication on
the GSUP protocol.
This setting only applies if auth-policy remote is used.
</description>
</command>
<command id='gsup oap-opc OPC'>
<description>
Set the OAP shared secret OPC for authentication on the
GSUP protocol.
This setting only applies if auth-policy remote is used.
</description>
</command>
<command id='access-point-name NAME'>
<description>
Globally allow the given APN name for all subscribers.
</description>
</command>
<command id='cdr filename NAME'>
<description>
Set the file name for the call-data-record file,
logging the data usage of each subscriber.
</description>
</command>
<command id='cdr interval <1-2147483647>'>
<description>
Set the interval (in secodnds) for the call-data-record
file.
</description>
</command>
</node>
</vtydoc>
|
