|Age||Commit message (Collapse)||Author||Files||Lines|
60 seconds is used by default, which is the minimum accepted value for
this timer as per 3GPP TS 29.060 section "7.2.1 Echo Request".
Having it low by default is good for lab use in which a lot of stuff
changes over time.
These either remain from openbsc.git or slipped in while applying recent
patches from openbsc.git and do not belong in osmo-sgsn.
In SGSN, actually place the port in the SGSN config by default, so that the
gsup port may now be omitted in the VTY config (the IP address suffices).
Adjust the osmo-sgsn.cfg example.
Depends: I4222e21686c823985be8ff1f16b1182be8ad6175 (libosmocore)
This was originally a long series of commits converging to the final result
seen in this patch. It does not make much sense to review the smaller steps'
trial and error, we need to review this entire change as a whole.
Implement AoIP in osmo-msc and osmo-bsc.
Change over to the new libosmo-sigtran API with support for proper
SCCP/M3UA/SCTP stacking, as mandated by 3GPP specifications for the IuCS and
From here on, a separate osmo-stp process is required for SCCP routing between
OsmoBSC / OsmoHNBGW <-> OsmoMSC / OsmoSGSN
jenkins.sh: build from libosmo-sccp and osmo-iuh master branches now for new
Patch-by: pmaier, nhofmeyr, laforge
A number of the GSM timers (including T3109) had no reasonable
default values if not specified in the VTY / config file. Together
with unconditional writing to the config file, this created
config files with a persistent setting for important timers as '0'.
To make things worse, many of our example cofig files suffered from the
Let's avoid this from happening by
* having reasonable defaults if nothing specified in the config file
* conditionally savingg timers only if they differ from default
* reject any timer values that state zero during start-up (see previous
For the vty tests, add osmo-sgsn-accept-all.cfg (that does not need an HLR) and
use in vty_test_runner.py, otherwise the 'show sgsn' command will reply that it
could not connect to the HLR, failing the vty test which expects empty.
This helps in providing 3G software packages for the sysmoNITB hardware, which
uses 10.23.24.1 for SGSN and 10.23.24.2 for GGSN.
However, in order to not break the python tests, the osmo-sgsn.cfg example
still uses 127.0.0.1 as local address.
Change the GGSN address to 127.0.0.2, because SGSN and GGSN cannot co-exist on
the same address (the GTP port number is fixed by spec: no IE to communicate a
differing port, so it has to be the standard GTP port for both).
osmo-nitb becomes osmo-msc
add DIUCS debug log constant
add msc vty, remove nitb vty
add libiudummy, to avoid linking Iu deps in tests
Use new msc_tx_dtap() instead of gsm0808_submit_dtap()
libmgcp: add mgcpgw client API
bridge calls via mgcpgw
Enable MSC specific CTRL commands, bsc_base_ctrl_cmds_install() still needs to
be split up.
Original libvlr code is by Harald Welte <email@example.com>,
polished and tweaked by Neels Hofmeyr <firstname.lastname@example.org>.
This is a long series of trial-and-error development collapsed in one patch.
This may be split in smaller commits if reviewers prefer that. If we can keep
it as one, we have saved ourselves the additional separation work.
The SQL based lookup of SMS for attached subscribers no longer works since the
SQL database no longer has the subscriber data. Replace with a round-robin on
the SMS recipient MSISDNs paired with a VLR subscriber RAM lookup whether the
subscriber is currently attached.
If there are many SMS for not-attached subscribers in the SMS database, this
will become inefficient: a DB hit returns a pending SMS, the RAM lookup will
reveal that the subscriber is not attached, after which the DB is hit for the
next SMS. It would become more efficient e.g. by having an MSISDN based hash
list for the VLR subscribers and by marking non-attached SMS recipients in the
SMS database so that they can be excluded with the SQL query already.
There is a sanity limit to do at most 100 db hits per attempt to find a pending
SMS. So if there are more than 100 stored SMS waiting for their recipients to
actually attach to the MSC, it may take more than one SMS queue trigger to
deliver SMS for subscribers that are actually attached.
This is not very beautiful, but is merely intended to carry us over to a time
when we have a proper separate SMSC entity.
Introduce gsm_subscriber_connection ref-counting in libmsc.
Remove/Disable VTY and CTRL commands to create subscribers, which is now a task
of the OsmoHLR. Adjust the python tests accordingly.
Remove VTY cmd subscriber-keep-in-ram.
Use OSMO_GSUP_PORT = 4222 instead of 2222. See
So far use the LAC from conn->bts, will be replaced by conn->lac in
Related: OS#1592 OS#1974
- bscs.config needed by the vty tests was not picked up as a dist file, because
its suffix is not 'cfg'. Rename to *.cfg. Apply this rename in
vty_test_runner.py and osmo-bsc_nat.cfg.
- Remove restart counters after external tests, otherwise distcheck complains
about uncleaned files.
- Add contrib/ipa.py to EXTRA_DIST, hence add a Makefile.am to contrib/.
Otherwise the python tests cannot find that dependency.
This is the first step in creating this repository from the legacy openbsc.git.
Like all other Osmocom repositories, keep the autoconf and automake files in
the repository root. openbsc.git has been the sole exception, which ends now.