diff options
Diffstat (limited to 'doc/manuals/vty/sgsn_vty_additions.xml')
| -rw-r--r-- | doc/manuals/vty/sgsn_vty_additions.xml | 113 |
1 files changed, 3 insertions, 110 deletions
diff --git a/doc/manuals/vty/sgsn_vty_additions.xml b/doc/manuals/vty/sgsn_vty_additions.xml index dd26dbacc..660b695f7 100644 --- a/doc/manuals/vty/sgsn_vty_additions.xml +++ b/doc/manuals/vty/sgsn_vty_additions.xml @@ -1,113 +1,6 @@ <vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'> - <node id='26'> - <child_of nodeid='4' /> - <name>SGSN Configuration Node</name> - <description>Configure the remote GGSN, access-control and other - attributes of the SGSN</description> - <command id='gtp local-ip A.B.C.D'> - <description> - Configure the local IP address to which the SGSN should - bind for the Gp interface (towards the GGSNs). - - Please note that in case you would like to run the GGSN - on the same machine as the SGSN, you can not run both on - the same IP address. It is suggested to use 127.0.0.1 - for the SGSN and 127.0.0.2 for the GGSN in such - situations. - </description> - </command> - <command id='ggsn <0-255> remote-ip A.B.C.D'> - <description> - Configure a static GGSN with a given numeric identifier - to use the specified remote IP address. - </description> - </command> - <command id='ggsn <0-255> gtp-version (0|1)'> - <description> - Configure whether to use GTPv0 or GTPv1 towards the - specified GSSN number. - </description> - </command> - <command id='ggsn dynamic'> - <description> - Enable dynamic resolving of GGSNs based on DNS resolving - the APN name like in a GRX-style setup. Changing this - setting requires a re-start of the SGSN. - </description> - </command> - <command id='grx-dns-add A.B.C.D'> - <description> - Use the specified IP address for DNS-resolving the AP - names to GGSN IP addresses - </description> - </command> - <command id='apn APNAME ggsn <0-255>'> - <description> - Map the given APN Name to the given GGSN number. - </description> - </command> - <command id='apn APNAME imsi-prefx IMSIPRE ggsn <0-255>'> - <description> - Map the given APN Name to the given GGSN number _only_ - if the IMSI matches the given prefix. - </description> - </command> - <command id='imsi-acl (add|del) IMSI'> - <description> - Add or delete the given IMSI to/from the global Access - Control List. - </description> - </command> - <command id='auth-policy (accept-all|closed|acl-only|remote)'> - <description> - Configure the Authorization policy of the SGSN. This - setting determines which subscribers are permitted to - register to the network. - </description> - </command> - <command id='gsup remote-ip A.B.C.D'> - <description> - Set the IP address of the HLR (gateway) for the GSUP protocol. - This setting only applies if auth-policy remote is used. - </description> - </command> - <command id='gsup oap-id <0-65535>'> - <description> - Set the OAP client ID for authentication on the GSUP - protocol. - This setting only applies if auth-policy remote is used. - </description> - </command> - <command id='gsup oap-k K'> - <description> - Set the OAP shared secret key K for authentication on - the GSUP protocol. - This setting only applies if auth-policy remote is used. - </description> - </command> - <command id='gsup oap-opc OPC'> - <description> - Set the OAP shared secret OPC for authentication on the - GSUP protocol. - This setting only applies if auth-policy remote is used. - </description> - </command> - <command id='access-point-name NAME'> - <description> - Globally allow the given APN name for all subscribers. - </description> - </command> - <command id='cdr filename NAME'> - <description> - Set the file name for the call-data-record file, - logging the data usage of each subscriber. - </description> - </command> - <command id='cdr interval <1-2147483647>'> - <description> - Set the interval (in secodnds) for the call-data-record - file. - </description> - </command> + <node id='config-sgsn'> + <description>Configure the remote GGSN, access-control and other + attributes of the SGSN</description> </node> </vtydoc> |