1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
|
== BTS Configuration
The role of the BTS is to handle the GSM radio interface. When the BTS
application is starting, the A-bis OML connection is established towards
the BSC. Almost all BTS configuration (such as ARFCN, channel
configuration, transmit power, etc.) will be sent from the BSC to the
BTS via OML messages. After OML start-up has completed, the BSC will
instruct the BTS to establish the RSL connections.
Given that most configuration is downloaded from the BSC into the BTS at
start-up time, only some very basic settings have to be made in the
OsmoBTS software.
=== Command Line Options
Ths OsmoBTS executables (`osmo-bts-sysmo`, `osmo-bts-trx`,
`osmo-bts-octphy`, `osmo-bts-litecell15`, ...) share the following
generic command line options:
==== SYNOPSIS
*osmo-bts-sysmo* [-h|-V] [-d 'DBGMASK'] [-D] [-c 'CONFIGFILE' ] [-s] [-T] [-e 'LOGLEVEL'] [-r 'PRIO'] [-i 'GSMTAP-IP'] [-t <1-255>]
==== OPTIONS
*-h, --help*::
Print a short help message about the supported options
*-V, --version*::
Print the compile-time version number of the OsmoBTS program
*-d, --debug 'DBGMASK','DBGLEVELS'*::
Set the log subsystems and levels for logging to stderr. This
has mostly been superseded by VTY-based logging configuration,
see <<logging>> for further information.
*-D, --daemonize*::
Fork the process as a daemon into background.
*-c, --config-file 'CONFIGFILE'*::
Specify the file and path name of the configuration file to be
used. If none is specified, use `osmo-bts.cfg` in the current
working directory.
*-s, --disable-color*::
Disable colors for logging to stderr. This has mostly been
deprecated by VTY based logging configuration, see <<logging>>
for further information.
*-T, --timestamp*::
Enable time-stamping of log messages to stderr. This has mostly
been deprecated by VTY based logging configuration, see
<<logging>> for further information.
*-e, --log-level 'LOGLEVEL'*::
Set the global log level for logging to stderr. This has mostly
been deprecated by VTY based logging configuration, see
<<logging>> for further information.
*-r, --realtime 'PRIO'*::
Enable use of the Linux kernel realtime priority scheduler with
the specified priority.
It is recommended you use this option on low-performance
embedded systems or systems that encounter high non-GSM/GPRS
load.
*-i, --gsmtap-ip 'GSMTAP-IP'*::
Specify the destination IP address for GSMTAP messages.
*-t, --trx-num <1-255>*::
Specify the number of TRX supported by this BTS.
There may be additional, hardware specific command line options by the
different bts_model implementations.
=== Configuration using the VTY
Most configuration as well as run-time monitoring and system
introspection is implemented using a command-line based interface
called _VTY_. A full reference syntax of all existing VTY command is
available as a separate document.
See <<vty>> for further information on the VTY.
==== Required BTS/TRX configuration
There are some settings that have to be configured locally in the
sysmoBTS, as they cannot be set remotely from the BSC. Those
settings are stored in the OsmoBTS configuration file, which commonly
is stored in `/etc/osmocom/osmo-bts.cfg`.
.Example Minimal configuration file
----
!
! OsmoBTS (0.0.1.100-0455) configuration saved from vty
!!
!
phy 0 <1>
instance 0 <2>
bts 0 <3>
band DCS1800
ipa unit-id 1801 0 <4>
oml remote-ip 192.168.100.11 <5>
trx 0 <6>
phy 0 instance 0 <7>
----
<1> You must configure at least one PHY link by means of the PHY node
<2> You must configure at least one PHY instance in the PHY link
<3> There is always exactly one BTS (`bts 0`) configured in OsmoBTS
<4> The `ipa unit-id` is what is used to identify this BTS to the BSC
<5> The OML Remote IP is the IP address of the BSC, to which the BTS shall connect to.
<6> There must be at least one trx (`trx 0`) in each BTS
<7> Every TRX must be mapped to a specific PHY instance this way
For a full reference of all available VTY configuration parameters,
please refer to the OsmoBTS VTY Reference document.
[[gsmtap]]
==== Configuring GSMTAP tracing
In addition to being able to obtain pcap protocol traces of the A-bis
communication and the text-based logging from the OsmoBTS
software, there is also the capability of tracing all communication on
the radio interface. To do so, OsmoBTS can encapsulate
MAC blocks (23byte messages at the L2-L1 interface) into _GSMTAP_ and send
them via UDP/IP. At that point, they can be captured with utilities like
*tcpdump* or *tshark* for further analysis by the *wireshark* protocol
analyzer.
In order to activate this feature, you first need to make sure to start
OsmoBTS using the `-i` or `--gsmtap-ip` command line option, specifying
the destination IP address for the GSMTAP messages. In most cases,
using 127.0.0.1 for passing the messages over the loopback (`lo`) device
will be sufficient.
OsmoBTS can selectively trace such messages by their L1 SAPI, for both
Rx and Tx. For a complete list of L1 SAPI values, please refer to the
_OsmoBTS VTY reference manual_ <<vty-ref-osmobts>>.
For example, to enable GSMTAP tracing for messages on all SDCCH
channels, you can use the gsmtap-sapi sdcch command at the CONFIG TRX
node of the OsmoBTS VTY.
.Example: Enabling GSMTAP for SDCCH
----
OsmoBTS> enable
OsmoBTS# configure terminal
OsmoBTS(config)# bts 0
OsmoBTS(bts)# trx 0
OsmoBTS(trx)# gsmtap-sapi sdcch
OsmoBTS(trx)# write <1>
----
<1> the `write` command will make the configuration persistent in the
configuration file. This is not required if you wish to enable GSMTAP
only in the current session of OsmoBTS.
De-activation can be performed similarly by using the `no gsmtap-sapi
sdcch` command at the `trx` node of the OsmoBTS VTY.
From the moment they are enabled via VTY, GSMTAP messages will be
generated and sent in UDP encapsulation to the IANA-registered UDP port
for GSMTAP (4729) at the IP address specified in the command line
argument.
==== Configuring power ramping
OsmoBTS can ramp up the power of its trx over time. This helps reduce
cell congestion in busy environments.
In this example, the trx starts with 5dBm output power which increases by 1dB
every two seconds until it reaches nominal power.
Power ramping can use the power-ramp commands at the CONFIG TRX node of the
OsmoBTS VTY.
.Example: Configure power ramping on trx 0
----
OsmoBTS> enable
OsmoBTS# configure terminal
OsmoBTS(config)# bts 0
OsmoBTS(bts)# trx 0
OsmoBTS(trx)# power-ramp max-initial 5 dBm
OsmoBTS(trx)# power-ramp step-size 1 dB
OsmoBTS(trx)# power-ramp step-interval 2
OsmoBTS(trx)# write <1>
----
<1> the `write` command will make the configuration persistent in the
configuration file.
De-activating power-ramping can be performed by setting the max-initial value
to the nominal power. The default max-initial value is 23 dBm.
==== Running multiple instances
It is possible to run multiple instances of `osmo-bts` on one and the same
machine, if the phy-interface is flexible enough to distinguish between
different phy hardware interfaces.
Since usually a BTS instance runs in conjunction with a dedicated PCU instance,
the socket path between PCU and BTS has to be distinguished between the running
instances. It is possible to change the default socket path via VTY config:
.Example: Personalize PCU socket path
----
bts 0
pcu-socket /tmp/pcu_bts_2
----
It is also necessary to separate the VTY anc CTRL interfaces of the different
instances. The VTY, as well as the CTRL interface can be bound to a free IP
address from the loopback range:
.Example: Binding VTY and CTRL interface to a specific IP address
----
line vty
bind 127.0.0.2
ctrl
bind 127.0.0.2
----
|
