| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Change-Id: I403b9029f57fec3fdec2c1e2cbeac0f6eab53f24
|
|
vty_install_default() and install_default() will soon be deprecated.
Depends: I5021c64a787b63314e0f2f1cba0b8fc7bff4f09b
Change-Id: I5e8e9d7989ee20fe722bdd3109965d5bce9519fb
|
|
Change-Id: Ia1b3d5e010c5b6ea8e655b79d9b36b08cd1ef4c4
|
|
This way the name of systemd service file will match the name of the
binary similar to lc15. Add aliases so the user can use both old and new
names regardless of which file is installed. Once the corresponding
changes to OE recipes are applied old file can be removed.
Based on work by Pau Espin Pedrol <pespin@sysmocom.de>
Change-Id: I08615eb625d488603aeb5962ad9f30869c0e77c5
|
|
|
|
This runs the entire procedure for calibration with reasonable
error and success checking. It can be triggered from the VTY
of the sysmobts-mgr right now.
What is missing is to hook up with GPSD to check if the system
has a fix and provide a mode that will continously run the
calibration command.
|
|
In the long run we will connect to GPSD and wait for a fix and
then run the calibration. The first step is to open (and re-open)
the control connection to the BTS.
As the connection is on localhost there should not be a computation
overhead to always have the connection open. When connecting assume
that the ASYNC connect worked directly as otherwise we get no
notification of the failure.
This looks like a "bug" of libosmo-abis that should check if the
socket has been connected or not.
|
|
Add new power actions for the sysmoBTS2050. This allows to
switch off the secondary/slave when the system temperature
is too high and back on when the normal level is reached.
Do not allow to switch off the master (so remove the enum
value), do not check if the slave is switching itself off.
|
|
Instead of keeping state to remember what was done and needs
to be undone this patch introduces actions that will be executed
when the system is back to normal.
By design the system is considered to be in the normal state
and these actions will be only executed after the system is
coming back to the normal state.
One advantage of this scheme is that an operator can decide
that an overheated systems hould be off duty and requires manual
interaction to be allowed back in service.
The change has only been smoke tested
Fixes: SYS#833
|
|
For systems without direct access to the PA the best option
is to simply switch off the bts service. This will stop the
transmission which will take load from the DSP/FPGA/RF circuit
and indirectly from the PA as well.
We should introduce "pa-on and bts-on" that can be executed
as "normal" action.
|
|
We can use this on both slave and master. But only have the
master switch on the PA.
|
|
The PA will be unconditionally turned. This makes it possible
that in case of a crash, the PA will be turned on and then we
will do the temperature measurement and turn it off again. There
are no known crashes with the sysmobts-mgr right now so the risk
seems to be okay. In case we can't switch off the PA we have no
way to escalate it right now. We have not seen a dead uc either
so the risk is okay as well.
We can't switch the PA back on once we reach the normal level
as the BTS might transmit with full power and we would need more
current than the power supply/rails can carry. So leave the
system off right now.
What is missing is to use the OML router to actually inform
the BSC that something bad has happened at the BTS.
|
|
|
|
The idea is that for different parts of the system we can define
thresholds for warning and critical (severe) temperate thresholds.
And once any of these temperatures is reached we will execute an
action. When crossing from NORMAL to WARNING or WARNING to SEVERE
we will need to apply some hysteris before switching back to the
lower level. E.g. when being SEVERE mode, at least wait until we
are below the warning level again. Besides being able to switch
off things we could start reducing the transmit power of the system
until the system is cold enough again.
No action is implemented so far, everything is varpoware!
|
|
We want to know which componets are enabled and the voltage and
current used by the components.
|
|
Read the sensors that are always present and the ones that
are only present on the sysmoBTS 2050.
|
|
Add VTY support to the manager. This way we can interactively
inspect the state of the system and trigger events.
|
|
Harald is right and that the code is generally not ready
for inclusion. I fell victim of trying to finish it while
the code is not ready at all. It is better to re-introduce
the patches in a smaller and more tested way.
The right way would have been a branch were ready things
are split-off the main/wip commit until everything is ready.
Revert "sysmobts: Have a common prefix for the enum"
This reverts commit 44980347f308fe5bbe48a933dbc81b82b53d310a.
Revert "utils: Used the enum manuf_type_id in the parameter of add_manufacturer_id_label"
This reverts commit 7d36e5ed46b630203167fc9d5d28e0087fdbd394.
Revert "utils: Classify the OML message using the return type"
This reverts commit afee0b7929a00500f9c204f3bc7e12f72451e832.
Revert "sysmobts: Do not access out of bound string"
This reverts commit f5f41e805195c8c3294a9e6a68b10f975fbabbbd.
Revert "sysmobts: Separate IPA and OML check into two methods"
This reverts commit 13a224063dfcee0be529fba1c8fb9be9c1fb261e.
Revert "screenrc: osmobts-mgr now needs a config file"
This reverts commit 0a1699ff8a5462c167c24e8b28186abb26331698.
Revert "make sure osmobts-mgr.cfg file is included in tarballs"
This reverts commit 14c60b425f8146f6a392d2d3de2979c817cd975e.
Revert "sysmobts-mgr: Add VTY support for configuring it"
This reverts commit c5fedd24c96a4ef6d7a0c0ed3c70d6ef0abd5c17.
Revert "sysmobts: Add beginnings of an OML router and create Failure Messages in the sysmobts-manager"
This reverts commit c6ab90b27006ff2d1fdfb0b1d7fc01e1dd4a696d.
|
|
This patch allows to configure the warning temperature threshold,
the severe temperature threshold of the board and the PA and the
actions like the relative value power that we want to reduce the
transmit power to and the part that we want to switch off or not.
Signed-off-by: Alvaro Neira Ayuso <anayuso@sysmocom.de>
|
