diff options
Diffstat (limited to 'doc/manuals/vty/libbsc_vty_additions.xml')
-rw-r--r-- | doc/manuals/vty/libbsc_vty_additions.xml | 244 |
1 files changed, 244 insertions, 0 deletions
diff --git a/doc/manuals/vty/libbsc_vty_additions.xml b/doc/manuals/vty/libbsc_vty_additions.xml new file mode 100644 index 000000000..868539850 --- /dev/null +++ b/doc/manuals/vty/libbsc_vty_additions.xml @@ -0,0 +1,244 @@ +<vtydoc xmlns='urn:osmocom:xml:libosmocore:vty:doc:1.0'> + <node id='14'> + <child_of nodeid='4' /> + <name>GSM Network Configuration</name> + <description>This is the base node for all configuration of + GSM network related configuration, it includes the LAC, CI + access criteria but also the configuration of each BTS in this + network.</description> + </node> + <node id='15'> + <child_of nodeid='14' /> + <name>BTS Configuration</name> + <description>This is the configuration of a single BTS.</description> + <command id='oml ip.access stream_id <0-255> line E1_LINE'> + <description> + Set the IPA stream identifier for the OML link within the IPA + multiplex. Must be the same as on the BTS side. The default + value is 255. Only applies to BTSs connected via Abis/IP + interface. + </description> + </command> + <command id='is-connection-list (add|del) <0-2047> <0-2047> <0-255>'> + <description> + Only applies to Ericsson OML2000 based BTSs. + </description> + </command> + <command id='con-connection-list (add|del) <1-255> <0-1023> deconcentrated'> + <description> + Only applies to Ericsson OML2000 based BTSs. + </description> + </command> + <command id='con-connection-list (add|del) <1-255> <0-1023> tei <0-63>'> + <description> + Only applies to Ericsson OML2000 based BTSs. + </description> + </command> + <command id='channel-descrption attach (0|1)'> + <description> + Configure whether the IMSI ATTACH (and DETACH) procedures + shall be used by MS in this cell. The default should be enabled. + </description> + </command> + <command id='ip.access rsl-ip A.B.C.D'> + <description> + Configure the IP address of the BSC used for RSL. Abis/IP + BTSs, including OsmoBTS and the nanoBTS will be instructed to + connect their RSL links to that IP address. + </description> + </command> + <command id='base_station_id_code <0-63>'> + <description> + Configure the BSIC of the cell. It is a 6-bit value + consisting of a 3-bit NCC (network color code) in the upper 3 + bits, and a 3-bit BCC (base station color code) in the lower 3 + bits. + </description> + </command> + <command id='training_sequence_code <0-7>'> + <description> + Configure the default TSC for all timeslots on all TRX of the BTS. + The normal default is to use the BCC part of the BSIC as TSC. + Not all BTS models support a TSC != BCC. + </description> + </command> + <command id='si5 neighbor-list (add|del) arfcn <0-1023>'> + <description> + Add or remove an ARFCN to/from the list of neighbor cells + advertised in dedicated mode via SACCH. This command is only + available in manual-si5 neighbor-list mode. + </description> + </command> + <command id='neighbor-list (add|del) arfcn <0-1023>'> + <description> + Add or remove an ARFCN to/from the list of neighbor cells. + This command is only available in manual neighbor-list mode. + </description> + </command> + <command id='gprs network-control-order (nc0|nc1|nc2)'> + <description> + </description> + </command> + <command id='cell reselection offset <0-126>'> + <description> + If a cell advertises a cell reselection offset (CRO), it will + become more attractive during cell re-selection, despite not + being received at a higher level than other cells. The CRO + of each neighbor cell is added to the respective received + signal level before comparing their values for re-selection. + </description> + </command> + <command id='cell reselection hysteresis <0-14>'> + <description> + The Cell Re-Selection Hysteresis determines how many dB a + neighbor cell must be stronger than the current serving cell + before the MS considers that neighbor cell as a candidate for + re-selection. + </description> + </command> + <command id='ip.access unit_id <0-65534> <0-255>'> + <description> + The ip.access unit ID is a parameter of the IPA + Signalling-over-IP multiplex. It is administratively + configured on the BTS side, and used by the BTS to identify + itself to the BSC. The BSC then selects the BTS configuration + for this Unit ID. It consists of three parts, the Site ID, + the BTS ID and the TRX ID. The TRX ID automatically + corresponds to to the transceiver number and is thus not + configurable here. + </description> + </command> + <command id='ms max power <0-40>'> + <description> + Configures the maximum transmit power (in dBm) that any MS may + use within this cell. + </description> + </command> + <command id='periodic location update <6-1530>'> + <description> + The periodic location updating interval determines how often + the MS will periodically perform a LOCATION UPDATE procedure, + despite not having actuall changed location. The value is + specified in minutes. + </description> + </command> + <command id='cell barred (0|1)'> + <description> + Using this command, you can enable/disable barring of the cell. + Barred cells are not visible/accessible to regular phones. + Only some special operator testing phones can be configured in + a way to ignore cell barring. + </description> + </command> + <command id='rxlev access min <0-63>'> + <description> + Using this command, you can determine the minimum downlink + signal receive level (RxLev), at which the BTS must be + received by the MS in order to attempt establishing dedicated + channels via the RACH. + </description> + </command> + <command id='rach access-control-class (0|1|2|3|4|5|6|7|8|9|11|12|13|14|15) (barred|allowed)'> + <description> + Using this command, you can configure which access control + classes are permitted to access this cell. The access control + class of a MS is determined by the contents of the EF.ACC file + on the SIM card. + + Access Control Class 10 corresponds to Emergency Calls, and is + thus not configurable this way. + </description> + </command> + <command id='rach emergency call allowed (0|1)'> + <description> + Using this command, you can determine if this cell permits the + use of the 'EMERGENCY CALL' feature. + + <warning>Unless you operate a public network with connection to the + public emergency services in compliance with applicable regulatory + requirements, you should always have emergency calls disabled (allowed + 0) - which is also the default configuration.</warning> + </description> + </command> + <command id='channel-descrption bs-ag-blks-res <0-7>'> + <description> + Using this command, you can specify how many blocks of the + downlink CCCH should be reserved for exclusive usage as AGCH. + + <warning>Not all BTS models currently support non-default configuration + of this parameter.</warning> + </description> + </command> + <command id='oml e1 tei <0-63>'> + <description> + Set the LAPD TEI used for the OML connection of this BTS. + Only applies to classic E1 based A-bis. + </description> + </command> + </node> + <node id='16'> + <child_of nodeid='15' /> + <name>TRX Configuration</name> + <description>This is the configuration of a TRX.</description> + <command id='nominal power <0-100>'> + <description> + Inform the BSC about the nominal RF transmit power of the BTS in dBm. + This value must be entered depending on the BTS model and + external setup such as amplifiers. Changing this value will + not change the actually transmitted power, it will just affect + the reporting in the BSC VTY. + </description> + </command> + <command id='max_power_red <0-100>'> + <description> + Request the actual RF transmit power of the BTS to be reduced + by the specified number of dB. + </description> + </command> + <command id='rsl e1 tei <0-63>'> + <description> + Set the LAPD TEI used for the RSL connection of this TRX. + Only applies to classic E1 based A-bis. + </description> + </command> + <command id='rf_locked (0|1)'> + <description> + Enable (1) or disable (0) the RF locking for this TRX. RF + locking is a mechanism by which the transmitter can be shut + down by administrative means, e.g. via the control interface. + </description> + </command> + </node> + <node id='17'> + <child_of nodeid='16' /> + <name>TS Configuration</name> + <description>This is the configuration of a TS.</description> + <command id='training_sequence_code <0-7>'> + <description> + Configure the timeslot to run on a different TSC than the + default TSC of the BTS (which is derived from the BCC part of the BSIC). + Please note that not all BTS models support timeslot-specific TSC! + </description> + </command> + <command id='hopping enabled (0|1)'> + <description> + Enable or disable frequency hopping for this timeslot. Please + note that not all BTS models may support frequency hopping, + and that frequency hopping is only permitted for secondary + TRXs, so TRX 0 must always be non-hopping. + </description> + </command> + </node> + <node id='22'> + <child_of nodeid='3' /> + <name>OML Commands</name> + <description>This node allows to manipulate the OML state of + a connected BTS. It is meant for testing during development.</description> + </node> + <node id='26'> + <child_of nodeid='3' /> + <name>OML2000 Commands</name> + <description>This node allows to issue OML2000 commands for + Ericsson BTS. It is meant for testing during development.</description> + </node> +</vtydoc> |