diff options
| author | Vadim Yanitskiy <vyanitskiy@sysmocom.de> | 2022-09-30 00:28:59 +0700 |
|---|---|---|
| committer | Vadim Yanitskiy <vyanitskiy@sysmocom.de> | 2022-09-30 01:02:57 +0700 |
| commit | 8631189d9ef38107c8a82a770d9d1a826ef8cf29 (patch) | |
| tree | 915fbcdc045dddc09eddf1f6f9715050f313f0c9 /doc/manuals/chapters | |
| parent | 6e9f5e54d2f6d2db4c81857f7bc977b97b571346 (diff) | |
power_control: add CTRL command for sending default params
There exists a VTY command for sending default power control params,
but so far there was no CTRL counterpart for it. This patch adds a
SET command 'send-power-control-defaults':
$ osmo_ctrl.py \
--host 127.0.0.1 -p 4249 \
--set "bts.0.send-power-control-defaults" 1
Similar to 'send-new-system-informations', this command takes an
arbitrary dummy value (required for SET), which is simply ignored.
Change-Id: Ib370bd97ee2d9f72f8bec553550b1792d1345387
Related: SYS#6138
Diffstat (limited to 'doc/manuals/chapters')
| -rw-r--r-- | doc/manuals/chapters/control.adoc | 1 | ||||
| -rw-r--r-- | doc/manuals/chapters/power_control.adoc | 15 |
2 files changed, 14 insertions, 2 deletions
diff --git a/doc/manuals/chapters/control.adoc b/doc/manuals/chapters/control.adoc index 09e828e9e..8009ec72e 100644 --- a/doc/manuals/chapters/control.adoc +++ b/doc/manuals/chapters/control.adoc @@ -33,6 +33,7 @@ TRX-specific commands are additionally prefixed with TRX number e. g. |bts.N.cell-identity|RW|No|"<id>"|Set/Get Cell Identity (value between (0, 65535)). |bts.N.apply-configuration|WO|No|Ignored|Restart BTS via OML. |bts.N.send-new-system-informations|WO|No|Ignored|Regenerate and resend System Information messages for given BTS. +|bts.N.send-power-control-defaults|WO|No|Ignored|Resend default power control parameters for given BTS. |bts.N.channel-load|RO|No|"<name>,<used>,<total>"|See <<chanlo>> for details. |bts.N.oml-connection-state|RO|No|"connected", "disconnected", "degraded"|Indicate the status of OML connection of BTS. |bts.N.oml-uptime|RO|No|<uptime>|Return OML link uptime in seconds. diff --git a/doc/manuals/chapters/power_control.adoc b/doc/manuals/chapters/power_control.adoc index f5f94f6a4..9b48f1551 100644 --- a/doc/manuals/chapters/power_control.adoc +++ b/doc/manuals/chapters/power_control.adoc @@ -53,13 +53,24 @@ BTS that accepts the default parameters at startup without triggering the A-bis/ link re-establishment and thus interrupting the service. The following command triggers resending of both MS/BS power control parameters: +.Example: Resending default power control parameters via the VTY ---- # Resending from the 'enable' node: -OsmoBSC# bts 0 resend-power-control-defaults +OsmoBSC# bts 0 <1> resend-power-control-defaults # Resending from any configuration node (note prefix 'do'): -OsmoBSC(config-ms-power-ctrl)# do bts 0 resend-power-control-defaults +OsmoBSC(config-ms-power-ctrl)# do bts 0 <1> resend-power-control-defaults ---- +<1> BTS number for which to resend default power control parameters. + +.Example: Resending default power control parameters via the CTRL +---- +$ osmo_ctrl.py \ + --host 127.0.0.1 <1> -p 4249 \ + --set "bts.0.send-power-control-defaults" 1 <2> +---- +<1> Remote address of the host running osmo-bsc (localhost in this example). +<2> An arbitrary dummy value (ignored). Required because SET command is used. NOTE: The above statement mostly applies to parameters for dynamic power control mode (see below). Switching between power control modes, as well as changing |