|author||Harald Welte <firstname.lastname@example.org>||2019-02-04 22:52:31 +0100|
|committer||Harald Welte <email@example.com>||2019-02-05 14:45:26 +0000|
manual: Add sections on 3G/4G neighbor cells
This adds some instructions on how to configure 3G/4G neighbor cells within osmo-bsc. I didn't want to add a new top-level chapter but instead chose to add it to the handover section which describes also the configuration of 2G neighbors. Change-Id: I81df1a453858b6fca80c8adf234b1d5b8bf5283d
1 files changed, 102 insertions, 1 deletions
diff --git a/doc/manuals/chapters/handover.adoc b/doc/manuals/chapters/handover.adoc
index 297eafc1f..c75b03c40 100644
@@ -19,7 +19,8 @@ orchestrating completely separate RAN stacks.
OsmoBSC currently supports handover within one BSS and between separate BSS.
Whether inter-MSC is supported depends on the MSC implementation (to the BSC,
inter-MSC handover looks identical to inter-BSC handover). Inter-RAT handover
-is currently not implemented.
+is currently not implemented. However, you may still advertise 3G and 4G neighbor cells
+in order to facilitate cell/RAT re-selection to those neighbors.
At the time of writing, OsmoMSC's inter-BSC handover support is not complete
yet, so OsmoBSC can perform handover between separate BSS only in conjunction
@@ -575,3 +576,103 @@ OsmoBSC:
- Algorithm 1 has no `min rxlev` setting.
- Algorithm 1 does not actually use any information besides the Measurement
Reports, and hence can trivially treat all neighbor cells identically.
+=== Advertising 3G/4G neighbors
+Despite osmo-bsc not supporting inter-RAT hand-over at this point, it
+still makes sense to advertise neighbor cells of other network
+technologies like UMTS/UTRAN (3G) and LTE/EUTRAN (4G). This will help
+phones with idle-mode re-selection of the best available radio access
+For more information on the inter-RAT cell re-selection algorithm and its
+parameters, see 3GPP TS 45.008 - particularly Section 6.6.4 describing
+measurements on cells of other (non-GSM) RATs.
+Such neighbors are advertised as part of the SI2quater (System
+Information Type 2quater).
+==== UMTS/UTRAN/3G neighbors
+In order to advertise a 3G neighbor cell you have to specify the
+* the UARFCN (UTRAN Absolute Radio Channel Number) on which the cell
+* the Scrambling Code of the cell
+* whether or not the cell uses diversity
+In the following example, we're configuring a 3G neighbor cell on UARFCN
+1234 using the scrambling code 511 with no diversity:
+ bts 0
+ si2quater neighbor-list add uarfcn 1234 511 0
+3G neighbor cells can be removed using the same command, just replacing
+`add` with `del`.
+==== LTE/EUTRAN/4G neighbors
+In order to advertise a 4G neighbor cell you have to specify the
+* EARFCN (EUTRAN Absolute Radio Channel Number) on which the cell
+* Reselection thresholds towards E-UTRAN cells:
+| 0 | 0 dB
+| 1 | 2 dB
+| 2 | 4 dB
+| 3 | 6 dB
+| ... | ...
+| 31 | 62 dB
+* Priority of E-UTRAN frequency: 0 = lowest priority, ..., 7 = highest priority
+* QRXLEVMIN parameter: Minimum required RX level in the UTRAN FDD cell
+ (dBm), see 3GPP TS 25.304.
+| 0 | -140 dBm
+| 1 | -138 dBm
+| 2 | -136 dBm
+| ... | ...
+| 31 | -78 dBm
+* Measurement bandwidth in MHz, see 3GPP TS 44.018 and 3GPP TS 44.060.
+ This field specifies the minimum value of the channel bandwidth of all
+ valid E-UTRAN cells on the specified EARFCN. It is defined by the
+ parameter Transmission Bandwidth Configuration, N RB (see 3GPP TS
+ 36.104). The values indicate the number of resource blocks over which
+ the mobile station could measure if the mobile station does not
+ support wideband RSRQ measurements (see 3GPP TS 24.008). A mobile
+ station supporting wideband RSRQ measurements shall measure over the
+ indicated number of resource blocks. The field is coded according to
+ the following table:
+| 0 | N_RB = 6
+| 1 | N_RB = 15
+| 2 | N_RB = 25
+| 3 | N_RB = 50
+| 4 | N_RB = 75
+| 5 | N_RB = 100
+In the following example we're configuring a 4G neighbor on EARFCN 2342
+with a higher reselection threshold of 40dB, a lower reselection
+threshold of 20dB, priority 5, QRXLEVMIN of -140 dBm and a measurement
+bandwidth of 100 resource blocks:
+ bts 0
+ si2quater neighbor-list add earfcn 2342 thresh-hi 20 thresh-lo 10 prio 5 qrxlv 0 meas 5
+4G neighbor cells can be removed using the same command, just replacing
+`add` with `del`.