/** * \file * * \brief Component description for SUPC * * Copyright (c) 2018 Microchip Technology Inc. * * \asf_license_start * * \page License * * SPDX-License-Identifier: Apache-2.0 * * Licensed under the Apache License, Version 2.0 (the "License"); you may * not use this file except in compliance with the License. * You may obtain a copy of the Licence at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an AS IS BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. * * \asf_license_stop * */ #ifndef _SAME54_SUPC_COMPONENT_ #define _SAME54_SUPC_COMPONENT_ /* ========================================================================== */ /** SOFTWARE API DEFINITION FOR SUPC */ /* ========================================================================== */ /** \addtogroup SAME54_SUPC Supply Controller */ /*@{*/ #define SUPC_U2407 #define REV_SUPC 0x110 /* -------- SUPC_INTENCLR : (SUPC Offset: 0x00) (R/W 32) Interrupt Enable Clear -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { struct { uint32_t BOD33RDY:1; /*!< bit: 0 BOD33 Ready */ uint32_t BOD33DET:1; /*!< bit: 1 BOD33 Detection */ uint32_t B33SRDY:1; /*!< bit: 2 BOD33 Synchronization Ready */ uint32_t BOD12RDY:1; /*!< bit: 3 BOD12 Ready */ uint32_t BOD12DET:1; /*!< bit: 4 BOD12 Detection */ uint32_t B12SRDY:1; /*!< bit: 5 BOD12 Synchronization Ready */ uint32_t :2; /*!< bit: 6.. 7 Reserved */ uint32_t VREGRDY:1; /*!< bit: 8 Voltage Regulator Ready */ uint32_t :1; /*!< bit: 9 Reserved */ uint32_t VCORERDY:1; /*!< bit: 10 VDDCORE Ready */ uint32_t :21; /*!< bit: 11..31 Reserved */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_INTENCLR_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_INTENCLR_OFFSET 0x00 /**< \brief (SUPC_INTENCLR offset) Interrupt Enable Clear */ #define SUPC_INTENCLR_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_INTENCLR reset_value) Interrupt Enable Clear */ #define SUPC_INTENCLR_BOD33RDY_Pos 0 /**< \brief (SUPC_INTENCLR) BOD33 Ready */ #define SUPC_INTENCLR_BOD33RDY (_U_(0x1) << SUPC_INTENCLR_BOD33RDY_Pos) #define SUPC_INTENCLR_BOD33DET_Pos 1 /**< \brief (SUPC_INTENCLR) BOD33 Detection */ #define SUPC_INTENCLR_BOD33DET (_U_(0x1) << SUPC_INTENCLR_BOD33DET_Pos) #define SUPC_INTENCLR_B33SRDY_Pos 2 /**< \brief (SUPC_INTENCLR) BOD33 Synchronization Ready */ #define SUPC_INTENCLR_B33SRDY (_U_(0x1) << SUPC_INTENCLR_B33SRDY_Pos) #define SUPC_INTENCLR_BOD12RDY_Pos 3 /**< \brief (SUPC_INTENCLR) BOD12 Ready */ #define SUPC_INTENCLR_BOD12RDY (_U_(0x1) << SUPC_INTENCLR_BOD12RDY_Pos) #define SUPC_INTENCLR_BOD12DET_Pos 4 /**< \brief (SUPC_INTENCLR) BOD12 Detection */ #define SUPC_INTENCLR_BOD12DET (_U_(0x1) << SUPC_INTENCLR_BOD12DET_Pos) #define SUPC_INTENCLR_B12SRDY_Pos 5 /**< \brief (SUPC_INTENCLR) BOD12 Synchronization Ready */ #define SUPC_INTENCLR_B12SRDY (_U_(0x1) << SUPC_INTENCLR_B12SRDY_Pos) #define SUPC_INTENCLR_VREGRDY_Pos 8 /**< \brief (SUPC_INTENCLR) Voltage Regulator Ready */ #define SUPC_INTENCLR_VREGRDY (_U_(0x1) << SUPC_INTENCLR_VREGRDY_Pos) #define SUPC_INTENCLR_VCORERDY_Pos 10 /**< \brief (SUPC_INTENCLR) VDDCORE Ready */ #define SUPC_INTENCLR_VCORERDY (_U_(0x1) << SUPC_INTENCLR_VCORERDY_Pos) #define SUPC_INTENCLR_MASK _U_(0x0000053F) /**< \brief (SUPC_INTENCLR) MASK Register */ /* -------- SUPC_INTENSET : (SUPC Offset: 0x04) (R/W 32) Interrupt Enable Set -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { struct { uint32_t BOD33RDY:1; /*!< bit: 0 BOD33 Ready */ uint32_t BOD33DET:1; /*!< bit: 1 BOD33 Detection */ uint32_t B33SRDY:1; /*!< bit: 2 BOD33 Synchronization Ready */ uint32_t BOD12RDY:1; /*!< bit: 3 BOD12 Ready */ uint32_t BOD12DET:1; /*!< bit: 4 BOD12 Detection */ uint32_t B12SRDY:1; /*!< bit: 5 BOD12 Synchronization Ready */ uint32_t :2; /*!< bit: 6.. 7 Reserved */ uint32_t VREGRDY:1; /*!< bit: 8 Voltage Regulator Ready */ uint32_t :1; /*!< bit: 9 Reserved */ uint32_t VCORERDY:1; /*!< bit: 10 VDDCORE Ready */ uint32_t :21; /*!< bit: 11..31 Reserved */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_INTENSET_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_INTENSET_OFFSET 0x04 /**< \brief (SUPC_INTENSET offset) Interrupt Enable Set */ #define SUPC_INTENSET_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_INTENSET reset_value) Interrupt Enable Set */ #define SUPC_INTENSET_BOD33RDY_Pos 0 /**< \brief (SUPC_INTENSET) BOD33 Ready */ #define SUPC_INTENSET_BOD33RDY (_U_(0x1) << SUPC_INTENSET_BOD33RDY_Pos) #define SUPC_INTENSET_BOD33DET_Pos 1 /**< \brief (SUPC_INTENSET) BOD33 Detection */ #define SUPC_INTENSET_BOD33DET (_U_(0x1) << SUPC_INTENSET_BOD33DET_Pos) #define SUPC_INTENSET_B33SRDY_Pos 2 /**< \brief (SUPC_INTENSET) BOD33 Synchronization Ready */ #define SUPC_INTENSET_B33SRDY (_U_(0x1) << SUPC_INTENSET_B33SRDY_Pos) #define SUPC_INTENSET_BOD12RDY_Pos 3 /**< \brief (SUPC_INTENSET) BOD12 Ready */ #define SUPC_INTENSET_BOD12RDY (_U_(0x1) << SUPC_INTENSET_BOD12RDY_Pos) #define SUPC_INTENSET_BOD12DET_Pos 4 /**< \brief (SUPC_INTENSET) BOD12 Detection */ #define SUPC_INTENSET_BOD12DET (_U_(0x1) << SUPC_INTENSET_BOD12DET_Pos) #define SUPC_INTENSET_B12SRDY_Pos 5 /**< \brief (SUPC_INTENSET) BOD12 Synchronization Ready */ #define SUPC_INTENSET_B12SRDY (_U_(0x1) << SUPC_INTENSET_B12SRDY_Pos) #define SUPC_INTENSET_VREGRDY_Pos 8 /**< \brief (SUPC_INTENSET) Voltage Regulator Ready */ #define SUPC_INTENSET_VREGRDY (_U_(0x1) << SUPC_INTENSET_VREGRDY_Pos) #define SUPC_INTENSET_VCORERDY_Pos 10 /**< \brief (SUPC_INTENSET) VDDCORE Ready */ #define SUPC_INTENSET_VCORERDY (_U_(0x1) << SUPC_INTENSET_VCORERDY_Pos) #define SUPC_INTENSET_MASK _U_(0x0000053F) /**< \brief (SUPC_INTENSET) MASK Register */ /* -------- SUPC_INTFLAG : (SUPC Offset: 0x08) (R/W 32) Interrupt Flag Status and Clear -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { // __I to avoid read-modify-write on write-to-clear register struct { __I uint32_t BOD33RDY:1; /*!< bit: 0 BOD33 Ready */ __I uint32_t BOD33DET:1; /*!< bit: 1 BOD33 Detection */ __I uint32_t B33SRDY:1; /*!< bit: 2 BOD33 Synchronization Ready */ __I uint32_t BOD12RDY:1; /*!< bit: 3 BOD12 Ready */ __I uint32_t BOD12DET:1; /*!< bit: 4 BOD12 Detection */ __I uint32_t B12SRDY:1; /*!< bit: 5 BOD12 Synchronization Ready */ __I uint32_t :2; /*!< bit: 6.. 7 Reserved */ __I uint32_t VREGRDY:1; /*!< bit: 8 Voltage Regulator Ready */ __I uint32_t :1; /*!< bit: 9 Reserved */ __I uint32_t VCORERDY:1; /*!< bit: 10 VDDCORE Ready */ __I uint32_t :21; /*!< bit: 11..31 Reserved */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_INTFLAG_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_INTFLAG_OFFSET 0x08 /**< \brief (SUPC_INTFLAG offset) Interrupt Flag Status and Clear */ #define SUPC_INTFLAG_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_INTFLAG reset_value) Interrupt Flag Status and Clear */ #define SUPC_INTFLAG_BOD33RDY_Pos 0 /**< \brief (SUPC_INTFLAG) BOD33 Ready */ #define SUPC_INTFLAG_BOD33RDY (_U_(0x1) << SUPC_INTFLAG_BOD33RDY_Pos) #define SUPC_INTFLAG_BOD33DET_Pos 1 /**< \brief (SUPC_INTFLAG) BOD33 Detection */ #define SUPC_INTFLAG_BOD33DET (_U_(0x1) << SUPC_INTFLAG_BOD33DET_Pos) #define SUPC_INTFLAG_B33SRDY_Pos 2 /**< \brief (SUPC_INTFLAG) BOD33 Synchronization Ready */ #define SUPC_INTFLAG_B33SRDY (_U_(0x1) << SUPC_INTFLAG_B33SRDY_Pos) #define SUPC_INTFLAG_BOD12RDY_Pos 3 /**< \brief (SUPC_INTFLAG) BOD12 Ready */ #define SUPC_INTFLAG_BOD12RDY (_U_(0x1) << SUPC_INTFLAG_BOD12RDY_Pos) #define SUPC_INTFLAG_BOD12DET_Pos 4 /**< \brief (SUPC_INTFLAG) BOD12 Detection */ #define SUPC_INTFLAG_BOD12DET (_U_(0x1) << SUPC_INTFLAG_BOD12DET_Pos) #define SUPC_INTFLAG_B12SRDY_Pos 5 /**< \brief (SUPC_INTFLAG) BOD12 Synchronization Ready */ #define SUPC_INTFLAG_B12SRDY (_U_(0x1) << SUPC_INTFLAG_B12SRDY_Pos) #define SUPC_INTFLAG_VREGRDY_Pos 8 /**< \brief (SUPC_INTFLAG) Voltage Regulator Ready */ #define SUPC_INTFLAG_VREGRDY (_U_(0x1) << SUPC_INTFLAG_VREGRDY_Pos) #define SUPC_INTFLAG_VCORERDY_Pos 10 /**< \brief (SUPC_INTFLAG) VDDCORE Ready */ #define SUPC_INTFLAG_VCORERDY (_U_(0x1) << SUPC_INTFLAG_VCORERDY_Pos) #define SUPC_INTFLAG_MASK _U_(0x0000053F) /**< \brief (SUPC_INTFLAG) MASK Register */ /* -------- SUPC_STATUS : (SUPC Offset: 0x0C) (R/ 32) Power and Clocks Status -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { struct { uint32_t BOD33RDY:1; /*!< bit: 0 BOD33 Ready */ uint32_t BOD33DET:1; /*!< bit: 1 BOD33 Detection */ uint32_t B33SRDY:1; /*!< bit: 2 BOD33 Synchronization Ready */ uint32_t BOD12RDY:1; /*!< bit: 3 BOD12 Ready */ uint32_t BOD12DET:1; /*!< bit: 4 BOD12 Detection */ uint32_t B12SRDY:1; /*!< bit: 5 BOD12 Synchronization Ready */ uint32_t :2; /*!< bit: 6.. 7 Reserved */ uint32_t VREGRDY:1; /*!< bit: 8 Voltage Regulator Ready */ uint32_t :1; /*!< bit: 9 Reserved */ uint32_t VCORERDY:1; /*!< bit: 10 VDDCORE Ready */ uint32_t :21; /*!< bit: 11..31 Reserved */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_STATUS_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_STATUS_OFFSET 0x0C /**< \brief (SUPC_STATUS offset) Power and Clocks Status */ #define SUPC_STATUS_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_STATUS reset_value) Power and Clocks Status */ #define SUPC_STATUS_BOD33RDY_Pos 0 /**< \brief (SUPC_STATUS) BOD33 Ready */ #define SUPC_STATUS_BOD33RDY (_U_(0x1) << SUPC_STATUS_BOD33RDY_Pos) #define SUPC_STATUS_BOD33DET_Pos 1 /**< \brief (SUPC_STATUS) BOD33 Detection */ #define SUPC_STATUS_BOD33DET (_U_(0x1) << SUPC_STATUS_BOD33DET_Pos) #define SUPC_STATUS_B33SRDY_Pos 2 /**< \brief (SUPC_STATUS) BOD33 Synchronization Ready */ #define SUPC_STATUS_B33SRDY (_U_(0x1) << SUPC_STATUS_B33SRDY_Pos) #define SUPC_STATUS_BOD12RDY_Pos 3 /**< \brief (SUPC_STATUS) BOD12 Ready */ #define SUPC_STATUS_BOD12RDY (_U_(0x1) << SUPC_STATUS_BOD12RDY_Pos) #define SUPC_STATUS_BOD12DET_Pos 4 /**< \brief (SUPC_STATUS) BOD12 Detection */ #define SUPC_STATUS_BOD12DET (_U_(0x1) << SUPC_STATUS_BOD12DET_Pos) #define SUPC_STATUS_B12SRDY_Pos 5 /**< \brief (SUPC_STATUS) BOD12 Synchronization Ready */ #define SUPC_STATUS_B12SRDY (_U_(0x1) << SUPC_STATUS_B12SRDY_Pos) #define SUPC_STATUS_VREGRDY_Pos 8 /**< \brief (SUPC_STATUS) Voltage Regulator Ready */ #define SUPC_STATUS_VREGRDY (_U_(0x1) << SUPC_STATUS_VREGRDY_Pos) #define SUPC_STATUS_VCORERDY_Pos 10 /**< \brief (SUPC_STATUS) VDDCORE Ready */ #define SUPC_STATUS_VCORERDY (_U_(0x1) << SUPC_STATUS_VCORERDY_Pos) #define SUPC_STATUS_MASK _U_(0x0000053F) /**< \brief (SUPC_STATUS) MASK Register */ /* -------- SUPC_BOD33 : (SUPC Offset: 0x10) (R/W 32) BOD33 Control -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { struct { uint32_t :1; /*!< bit: 0 Reserved */ uint32_t ENABLE:1; /*!< bit: 1 Enable */ uint32_t ACTION:2; /*!< bit: 2.. 3 Action when Threshold Crossed */ uint32_t STDBYCFG:1; /*!< bit: 4 Configuration in Standby mode */ uint32_t RUNSTDBY:1; /*!< bit: 5 Run in Standby mode */ uint32_t RUNHIB:1; /*!< bit: 6 Run in Hibernate mode */ uint32_t RUNBKUP:1; /*!< bit: 7 Run in Backup mode */ uint32_t HYST:4; /*!< bit: 8..11 Hysteresis value */ uint32_t PSEL:3; /*!< bit: 12..14 Prescaler Select */ uint32_t :1; /*!< bit: 15 Reserved */ uint32_t LEVEL:8; /*!< bit: 16..23 Threshold Level for VDD */ uint32_t VBATLEVEL:8; /*!< bit: 24..31 Threshold Level in battery backup sleep mode for VBAT */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_BOD33_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_BOD33_OFFSET 0x10 /**< \brief (SUPC_BOD33 offset) BOD33 Control */ #define SUPC_BOD33_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_BOD33 reset_value) BOD33 Control */ #define SUPC_BOD33_ENABLE_Pos 1 /**< \brief (SUPC_BOD33) Enable */ #define SUPC_BOD33_ENABLE (_U_(0x1) << SUPC_BOD33_ENABLE_Pos) #define SUPC_BOD33_ACTION_Pos 2 /**< \brief (SUPC_BOD33) Action when Threshold Crossed */ #define SUPC_BOD33_ACTION_Msk (_U_(0x3) << SUPC_BOD33_ACTION_Pos) #define SUPC_BOD33_ACTION(value) (SUPC_BOD33_ACTION_Msk & ((value) << SUPC_BOD33_ACTION_Pos)) #define SUPC_BOD33_ACTION_NONE_Val _U_(0x0) /**< \brief (SUPC_BOD33) No action */ #define SUPC_BOD33_ACTION_RESET_Val _U_(0x1) /**< \brief (SUPC_BOD33) The BOD33 generates a reset */ #define SUPC_BOD33_ACTION_INT_Val _U_(0x2) /**< \brief (SUPC_BOD33) The BOD33 generates an interrupt */ #define SUPC_BOD33_ACTION_BKUP_Val _U_(0x3) /**< \brief (SUPC_BOD33) The BOD33 puts the device in backup sleep mode */ #define SUPC_BOD33_ACTION_NONE (SUPC_BOD33_ACTION_NONE_Val << SUPC_BOD33_ACTION_Pos) #define SUPC_BOD33_ACTION_RESET (SUPC_BOD33_ACTION_RESET_Val << SUPC_BOD33_ACTION_Pos) #define SUPC_BOD33_ACTION_INT (SUPC_BOD33_ACTION_INT_Val << SUPC_BOD33_ACTION_Pos) #define SUPC_BOD33_ACTION_BKUP (SUPC_BOD33_ACTION_BKUP_Val << SUPC_BOD33_ACTION_Pos) #define SUPC_BOD33_STDBYCFG_Pos 4 /**< \brief (SUPC_BOD33) Configuration in Standby mode */ #define SUPC_BOD33_STDBYCFG (_U_(0x1) << SUPC_BOD33_STDBYCFG_Pos) #define SUPC_BOD33_RUNSTDBY_Pos 5 /**< \brief (SUPC_BOD33) Run in Standby mode */ #define SUPC_BOD33_RUNSTDBY (_U_(0x1) << SUPC_BOD33_RUNSTDBY_Pos) #define SUPC_BOD33_RUNHIB_Pos 6 /**< \brief (SUPC_BOD33) Run in Hibernate mode */ #define SUPC_BOD33_RUNHIB (_U_(0x1) << SUPC_BOD33_RUNHIB_Pos) #define SUPC_BOD33_RUNBKUP_Pos 7 /**< \brief (SUPC_BOD33) Run in Backup mode */ #define SUPC_BOD33_RUNBKUP (_U_(0x1) << SUPC_BOD33_RUNBKUP_Pos) #define SUPC_BOD33_HYST_Pos 8 /**< \brief (SUPC_BOD33) Hysteresis value */ #define SUPC_BOD33_HYST_Msk (_U_(0xF) << SUPC_BOD33_HYST_Pos) #define SUPC_BOD33_HYST(value) (SUPC_BOD33_HYST_Msk & ((value) << SUPC_BOD33_HYST_Pos)) #define SUPC_BOD33_PSEL_Pos 12 /**< \brief (SUPC_BOD33) Prescaler Select */ #define SUPC_BOD33_PSEL_Msk (_U_(0x7) << SUPC_BOD33_PSEL_Pos) #define SUPC_BOD33_PSEL(value) (SUPC_BOD33_PSEL_Msk & ((value) << SUPC_BOD33_PSEL_Pos)) #define SUPC_BOD33_PSEL_NODIV_Val _U_(0x0) /**< \brief (SUPC_BOD33) Not divided */ #define SUPC_BOD33_PSEL_DIV4_Val _U_(0x1) /**< \brief (SUPC_BOD33) Divide clock by 4 */ #define SUPC_BOD33_PSEL_DIV8_Val _U_(0x2) /**< \brief (SUPC_BOD33) Divide clock by 8 */ #define SUPC_BOD33_PSEL_DIV16_Val _U_(0x3) /**< \brief (SUPC_BOD33) Divide clock by 16 */ #define SUPC_BOD33_PSEL_DIV32_Val _U_(0x4) /**< \brief (SUPC_BOD33) Divide clock by 32 */ #define SUPC_BOD33_PSEL_DIV64_Val _U_(0x5) /**< \brief (SUPC_BOD33) Divide clock by 64 */ #define SUPC_BOD33_PSEL_DIV128_Val _U_(0x6) /**< \brief (SUPC_BOD33) Divide clock by 128 */ #define SUPC_BOD33_PSEL_DIV256_Val _U_(0x7) /**< \brief (SUPC_BOD33) Divide clock by 256 */ #define SUPC_BOD33_PSEL_NODIV (SUPC_BOD33_PSEL_NODIV_Val << SUPC_BOD33_PSEL_Pos) #define SUPC_BOD33_PSEL_DIV4 (SUPC_BOD33_PSEL_DIV4_Val << SUPC_BOD33_PSEL_Pos) #define SUPC_BOD33_PSEL_DIV8 (SUPC_BOD33_PSEL_DIV8_Val << SUPC_BOD33_PSEL_Pos) #define SUPC_BOD33_PSEL_DIV16 (SUPC_BOD33_PSEL_DIV16_Val << SUPC_BOD33_PSEL_Pos) #define SUPC_BOD33_PSEL_DIV32 (SUPC_BOD33_PSEL_DIV32_Val << SUPC_BOD33_PSEL_Pos) #define SUPC_BOD33_PSEL_DIV64 (SUPC_BOD33_PSEL_DIV64_Val << SUPC_BOD33_PSEL_Pos) #define SUPC_BOD33_PSEL_DIV128 (SUPC_BOD33_PSEL_DIV128_Val << SUPC_BOD33_PSEL_Pos) #define SUPC_BOD33_PSEL_DIV256 (SUPC_BOD33_PSEL_DIV256_Val << SUPC_BOD33_PSEL_Pos) #define SUPC_BOD33_LEVEL_Pos 16 /**< \brief (SUPC_BOD33) Threshold Level for VDD */ #define SUPC_BOD33_LEVEL_Msk (_U_(0xFF) << SUPC_BOD33_LEVEL_Pos) #define SUPC_BOD33_LEVEL(value) (SUPC_BOD33_LEVEL_Msk & ((value) << SUPC_BOD33_LEVEL_Pos)) #define SUPC_BOD33_VBATLEVEL_Pos 24 /**< \brief (SUPC_BOD33) Threshold Level in battery backup sleep mode for VBAT */ #define SUPC_BOD33_VBATLEVEL_Msk (_U_(0xFF) << SUPC_BOD33_VBATLEVEL_Pos) #define SUPC_BOD33_VBATLEVEL(value) (SUPC_BOD33_VBATLEVEL_Msk & ((value) << SUPC_BOD33_VBATLEVEL_Pos)) #define SUPC_BOD33_MASK _U_(0xFFFF7FFE) /**< \brief (SUPC_BOD33) MASK Register */ /* -------- SUPC_BOD12 : (SUPC Offset: 0x14) (R/W 32) BOD12 Control -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { struct { uint32_t :1; /*!< bit: 0 Reserved */ uint32_t ENABLE:1; /*!< bit: 1 Enable */ uint32_t HYST:1; /*!< bit: 2 Hysteresis Enable */ uint32_t ACTION:2; /*!< bit: 3.. 4 Action when Threshold Crossed */ uint32_t STDBYCFG:1; /*!< bit: 5 Configuration in Standby mode */ uint32_t RUNSTDBY:1; /*!< bit: 6 Run during Standby */ uint32_t :1; /*!< bit: 7 Reserved */ uint32_t ACTCFG:1; /*!< bit: 8 Configuration in Active mode */ uint32_t :3; /*!< bit: 9..11 Reserved */ uint32_t PSEL:4; /*!< bit: 12..15 Prescaler Select */ uint32_t LEVEL:6; /*!< bit: 16..21 Threshold Level */ uint32_t :10; /*!< bit: 22..31 Reserved */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_BOD12_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_BOD12_OFFSET 0x14 /**< \brief (SUPC_BOD12 offset) BOD12 Control */ #define SUPC_BOD12_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_BOD12 reset_value) BOD12 Control */ #define SUPC_BOD12_ENABLE_Pos 1 /**< \brief (SUPC_BOD12) Enable */ #define SUPC_BOD12_ENABLE (_U_(0x1) << SUPC_BOD12_ENABLE_Pos) #define SUPC_BOD12_HYST_Pos 2 /**< \brief (SUPC_BOD12) Hysteresis Enable */ #define SUPC_BOD12_HYST (_U_(0x1) << SUPC_BOD12_HYST_Pos) #define SUPC_BOD12_ACTION_Pos 3 /**< \brief (SUPC_BOD12) Action when Threshold Crossed */ #define SUPC_BOD12_ACTION_Msk (_U_(0x3) << SUPC_BOD12_ACTION_Pos) #define SUPC_BOD12_ACTION(value) (SUPC_BOD12_ACTION_Msk & ((value) << SUPC_BOD12_ACTION_Pos)) #define SUPC_BOD12_ACTION_NONE_Val _U_(0x0) /**< \brief (SUPC_BOD12) No action */ #define SUPC_BOD12_ACTION_RESET_Val _U_(0x1) /**< \brief (SUPC_BOD12) The BOD12 generates a reset */ #define SUPC_BOD12_ACTION_INT_Val _U_(0x2) /**< \brief (SUPC_BOD12) The BOD12 generates an interrupt */ #define SUPC_BOD12_ACTION_NONE (SUPC_BOD12_ACTION_NONE_Val << SUPC_BOD12_ACTION_Pos) #define SUPC_BOD12_ACTION_RESET (SUPC_BOD12_ACTION_RESET_Val << SUPC_BOD12_ACTION_Pos) #define SUPC_BOD12_ACTION_INT (SUPC_BOD12_ACTION_INT_Val << SUPC_BOD12_ACTION_Pos) #define SUPC_BOD12_STDBYCFG_Pos 5 /**< \brief (SUPC_BOD12) Configuration in Standby mode */ #define SUPC_BOD12_STDBYCFG (_U_(0x1) << SUPC_BOD12_STDBYCFG_Pos) #define SUPC_BOD12_RUNSTDBY_Pos 6 /**< \brief (SUPC_BOD12) Run during Standby */ #define SUPC_BOD12_RUNSTDBY (_U_(0x1) << SUPC_BOD12_RUNSTDBY_Pos) #define SUPC_BOD12_ACTCFG_Pos 8 /**< \brief (SUPC_BOD12) Configuration in Active mode */ #define SUPC_BOD12_ACTCFG (_U_(0x1) << SUPC_BOD12_ACTCFG_Pos) #define SUPC_BOD12_PSEL_Pos 12 /**< \brief (SUPC_BOD12) Prescaler Select */ #define SUPC_BOD12_PSEL_Msk (_U_(0xF) << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL(value) (SUPC_BOD12_PSEL_Msk & ((value) << SUPC_BOD12_PSEL_Pos)) #define SUPC_BOD12_PSEL_DIV2_Val _U_(0x0) /**< \brief (SUPC_BOD12) Divide clock by 2 */ #define SUPC_BOD12_PSEL_DIV4_Val _U_(0x1) /**< \brief (SUPC_BOD12) Divide clock by 4 */ #define SUPC_BOD12_PSEL_DIV8_Val _U_(0x2) /**< \brief (SUPC_BOD12) Divide clock by 8 */ #define SUPC_BOD12_PSEL_DIV16_Val _U_(0x3) /**< \brief (SUPC_BOD12) Divide clock by 16 */ #define SUPC_BOD12_PSEL_DIV32_Val _U_(0x4) /**< \brief (SUPC_BOD12) Divide clock by 32 */ #define SUPC_BOD12_PSEL_DIV64_Val _U_(0x5) /**< \brief (SUPC_BOD12) Divide clock by 64 */ #define SUPC_BOD12_PSEL_DIV128_Val _U_(0x6) /**< \brief (SUPC_BOD12) Divide clock by 128 */ #define SUPC_BOD12_PSEL_DIV256_Val _U_(0x7) /**< \brief (SUPC_BOD12) Divide clock by 256 */ #define SUPC_BOD12_PSEL_DIV512_Val _U_(0x8) /**< \brief (SUPC_BOD12) Divide clock by 512 */ #define SUPC_BOD12_PSEL_DIV1024_Val _U_(0x9) /**< \brief (SUPC_BOD12) Divide clock by 1024 */ #define SUPC_BOD12_PSEL_DIV2048_Val _U_(0xA) /**< \brief (SUPC_BOD12) Divide clock by 2048 */ #define SUPC_BOD12_PSEL_DIV4096_Val _U_(0xB) /**< \brief (SUPC_BOD12) Divide clock by 4096 */ #define SUPC_BOD12_PSEL_DIV8192_Val _U_(0xC) /**< \brief (SUPC_BOD12) Divide clock by 8192 */ #define SUPC_BOD12_PSEL_DIV16384_Val _U_(0xD) /**< \brief (SUPC_BOD12) Divide clock by 16384 */ #define SUPC_BOD12_PSEL_DIV32768_Val _U_(0xE) /**< \brief (SUPC_BOD12) Divide clock by 32768 */ #define SUPC_BOD12_PSEL_DIV65536_Val _U_(0xF) /**< \brief (SUPC_BOD12) Divide clock by 65536 */ #define SUPC_BOD12_PSEL_DIV2 (SUPC_BOD12_PSEL_DIV2_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV4 (SUPC_BOD12_PSEL_DIV4_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV8 (SUPC_BOD12_PSEL_DIV8_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV16 (SUPC_BOD12_PSEL_DIV16_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV32 (SUPC_BOD12_PSEL_DIV32_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV64 (SUPC_BOD12_PSEL_DIV64_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV128 (SUPC_BOD12_PSEL_DIV128_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV256 (SUPC_BOD12_PSEL_DIV256_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV512 (SUPC_BOD12_PSEL_DIV512_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV1024 (SUPC_BOD12_PSEL_DIV1024_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV2048 (SUPC_BOD12_PSEL_DIV2048_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV4096 (SUPC_BOD12_PSEL_DIV4096_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV8192 (SUPC_BOD12_PSEL_DIV8192_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV16384 (SUPC_BOD12_PSEL_DIV16384_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV32768 (SUPC_BOD12_PSEL_DIV32768_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_PSEL_DIV65536 (SUPC_BOD12_PSEL_DIV65536_Val << SUPC_BOD12_PSEL_Pos) #define SUPC_BOD12_LEVEL_Pos 16 /**< \brief (SUPC_BOD12) Threshold Level */ #define SUPC_BOD12_LEVEL_Msk (_U_(0x3F) << SUPC_BOD12_LEVEL_Pos) #define SUPC_BOD12_LEVEL(value) (SUPC_BOD12_LEVEL_Msk & ((value) << SUPC_BOD12_LEVEL_Pos)) #define SUPC_BOD12_MASK _U_(0x003FF17E) /**< \brief (SUPC_BOD12) MASK Register */ /* -------- SUPC_VREG : (SUPC Offset: 0x18) (R/W 32) VREG Control -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { struct { uint32_t :1; /*!< bit: 0 Reserved */ uint32_t ENABLE:1; /*!< bit: 1 Enable */ uint32_t SEL:1; /*!< bit: 2 Voltage Regulator Selection */ uint32_t :4; /*!< bit: 3.. 6 Reserved */ uint32_t RUNBKUP:1; /*!< bit: 7 Run in Backup mode */ uint32_t :8; /*!< bit: 8..15 Reserved */ uint32_t VSEN:1; /*!< bit: 16 Voltage Scaling Enable */ uint32_t :7; /*!< bit: 17..23 Reserved */ uint32_t VSPER:3; /*!< bit: 24..26 Voltage Scaling Period */ uint32_t :5; /*!< bit: 27..31 Reserved */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_VREG_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_VREG_OFFSET 0x18 /**< \brief (SUPC_VREG offset) VREG Control */ #define SUPC_VREG_RESETVALUE _U_(0x00000002) /**< \brief (SUPC_VREG reset_value) VREG Control */ #define SUPC_VREG_ENABLE_Pos 1 /**< \brief (SUPC_VREG) Enable */ #define SUPC_VREG_ENABLE (_U_(0x1) << SUPC_VREG_ENABLE_Pos) #define SUPC_VREG_SEL_Pos 2 /**< \brief (SUPC_VREG) Voltage Regulator Selection */ #define SUPC_VREG_SEL (_U_(0x1) << SUPC_VREG_SEL_Pos) #define SUPC_VREG_SEL_LDO_Val _U_(0x0) /**< \brief (SUPC_VREG) LDO selection */ #define SUPC_VREG_SEL_BUCK_Val _U_(0x1) /**< \brief (SUPC_VREG) Buck selection */ #define SUPC_VREG_SEL_LDO (SUPC_VREG_SEL_LDO_Val << SUPC_VREG_SEL_Pos) #define SUPC_VREG_SEL_BUCK (SUPC_VREG_SEL_BUCK_Val << SUPC_VREG_SEL_Pos) #define SUPC_VREG_RUNBKUP_Pos 7 /**< \brief (SUPC_VREG) Run in Backup mode */ #define SUPC_VREG_RUNBKUP (_U_(0x1) << SUPC_VREG_RUNBKUP_Pos) #define SUPC_VREG_VSEN_Pos 16 /**< \brief (SUPC_VREG) Voltage Scaling Enable */ #define SUPC_VREG_VSEN (_U_(0x1) << SUPC_VREG_VSEN_Pos) #define SUPC_VREG_VSPER_Pos 24 /**< \brief (SUPC_VREG) Voltage Scaling Period */ #define SUPC_VREG_VSPER_Msk (_U_(0x7) << SUPC_VREG_VSPER_Pos) #define SUPC_VREG_VSPER(value) (SUPC_VREG_VSPER_Msk & ((value) << SUPC_VREG_VSPER_Pos)) #define SUPC_VREG_MASK _U_(0x07010086) /**< \brief (SUPC_VREG) MASK Register */ /* -------- SUPC_VREF : (SUPC Offset: 0x1C) (R/W 32) VREF Control -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { struct { uint32_t :1; /*!< bit: 0 Reserved */ uint32_t TSEN:1; /*!< bit: 1 Temperature Sensor Output Enable */ uint32_t VREFOE:1; /*!< bit: 2 Voltage Reference Output Enable */ uint32_t TSSEL:1; /*!< bit: 3 Temperature Sensor Selection */ uint32_t :2; /*!< bit: 4.. 5 Reserved */ uint32_t RUNSTDBY:1; /*!< bit: 6 Run during Standby */ uint32_t ONDEMAND:1; /*!< bit: 7 On Demand Contrl */ uint32_t :8; /*!< bit: 8..15 Reserved */ uint32_t SEL:4; /*!< bit: 16..19 Voltage Reference Selection */ uint32_t :12; /*!< bit: 20..31 Reserved */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_VREF_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_VREF_OFFSET 0x1C /**< \brief (SUPC_VREF offset) VREF Control */ #define SUPC_VREF_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_VREF reset_value) VREF Control */ #define SUPC_VREF_TSEN_Pos 1 /**< \brief (SUPC_VREF) Temperature Sensor Output Enable */ #define SUPC_VREF_TSEN (_U_(0x1) << SUPC_VREF_TSEN_Pos) #define SUPC_VREF_VREFOE_Pos 2 /**< \brief (SUPC_VREF) Voltage Reference Output Enable */ #define SUPC_VREF_VREFOE (_U_(0x1) << SUPC_VREF_VREFOE_Pos) #define SUPC_VREF_TSSEL_Pos 3 /**< \brief (SUPC_VREF) Temperature Sensor Selection */ #define SUPC_VREF_TSSEL (_U_(0x1) << SUPC_VREF_TSSEL_Pos) #define SUPC_VREF_RUNSTDBY_Pos 6 /**< \brief (SUPC_VREF) Run during Standby */ #define SUPC_VREF_RUNSTDBY (_U_(0x1) << SUPC_VREF_RUNSTDBY_Pos) #define SUPC_VREF_ONDEMAND_Pos 7 /**< \brief (SUPC_VREF) On Demand Contrl */ #define SUPC_VREF_ONDEMAND (_U_(0x1) << SUPC_VREF_ONDEMAND_Pos) #define SUPC_VREF_SEL_Pos 16 /**< \brief (SUPC_VREF) Voltage Reference Selection */ #define SUPC_VREF_SEL_Msk (_U_(0xF) << SUPC_VREF_SEL_Pos) #define SUPC_VREF_SEL(value) (SUPC_VREF_SEL_Msk & ((value) << SUPC_VREF_SEL_Pos)) #define SUPC_VREF_SEL_1V0_Val _U_(0x0) /**< \brief (SUPC_VREF) 1.0V voltage reference typical value */ #define SUPC_VREF_SEL_1V1_Val _U_(0x1) /**< \brief (SUPC_VREF) 1.1V voltage reference typical value */ #define SUPC_VREF_SEL_1V2_Val _U_(0x2) /**< \brief (SUPC_VREF) 1.2V voltage reference typical value */ #define SUPC_VREF_SEL_1V25_Val _U_(0x3) /**< \brief (SUPC_VREF) 1.25V voltage reference typical value */ #define SUPC_VREF_SEL_2V0_Val _U_(0x4) /**< \brief (SUPC_VREF) 2.0V voltage reference typical value */ #define SUPC_VREF_SEL_2V2_Val _U_(0x5) /**< \brief (SUPC_VREF) 2.2V voltage reference typical value */ #define SUPC_VREF_SEL_2V4_Val _U_(0x6) /**< \brief (SUPC_VREF) 2.4V voltage reference typical value */ #define SUPC_VREF_SEL_2V5_Val _U_(0x7) /**< \brief (SUPC_VREF) 2.5V voltage reference typical value */ #define SUPC_VREF_SEL_1V0 (SUPC_VREF_SEL_1V0_Val << SUPC_VREF_SEL_Pos) #define SUPC_VREF_SEL_1V1 (SUPC_VREF_SEL_1V1_Val << SUPC_VREF_SEL_Pos) #define SUPC_VREF_SEL_1V2 (SUPC_VREF_SEL_1V2_Val << SUPC_VREF_SEL_Pos) #define SUPC_VREF_SEL_1V25 (SUPC_VREF_SEL_1V25_Val << SUPC_VREF_SEL_Pos) #define SUPC_VREF_SEL_2V0 (SUPC_VREF_SEL_2V0_Val << SUPC_VREF_SEL_Pos) #define SUPC_VREF_SEL_2V2 (SUPC_VREF_SEL_2V2_Val << SUPC_VREF_SEL_Pos) #define SUPC_VREF_SEL_2V4 (SUPC_VREF_SEL_2V4_Val << SUPC_VREF_SEL_Pos) #define SUPC_VREF_SEL_2V5 (SUPC_VREF_SEL_2V5_Val << SUPC_VREF_SEL_Pos) #define SUPC_VREF_MASK _U_(0x000F00CE) /**< \brief (SUPC_VREF) MASK Register */ /* -------- SUPC_BBPS : (SUPC Offset: 0x20) (R/W 32) Battery Backup Power Switch -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { struct { uint32_t CONF:1; /*!< bit: 0 Battery Backup Configuration */ uint32_t :1; /*!< bit: 1 Reserved */ uint32_t WAKEEN:1; /*!< bit: 2 Wake Enable */ uint32_t :29; /*!< bit: 3..31 Reserved */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_BBPS_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_BBPS_OFFSET 0x20 /**< \brief (SUPC_BBPS offset) Battery Backup Power Switch */ #define SUPC_BBPS_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_BBPS reset_value) Battery Backup Power Switch */ #define SUPC_BBPS_CONF_Pos 0 /**< \brief (SUPC_BBPS) Battery Backup Configuration */ #define SUPC_BBPS_CONF (_U_(0x1) << SUPC_BBPS_CONF_Pos) #define SUPC_BBPS_CONF_BOD33_Val _U_(0x0) /**< \brief (SUPC_BBPS) The power switch is handled by the BOD33 */ #define SUPC_BBPS_CONF_FORCED_Val _U_(0x1) /**< \brief (SUPC_BBPS) In Backup Domain, the backup domain is always supplied by battery backup power */ #define SUPC_BBPS_CONF_BOD33 (SUPC_BBPS_CONF_BOD33_Val << SUPC_BBPS_CONF_Pos) #define SUPC_BBPS_CONF_FORCED (SUPC_BBPS_CONF_FORCED_Val << SUPC_BBPS_CONF_Pos) #define SUPC_BBPS_WAKEEN_Pos 2 /**< \brief (SUPC_BBPS) Wake Enable */ #define SUPC_BBPS_WAKEEN (_U_(0x1) << SUPC_BBPS_WAKEEN_Pos) #define SUPC_BBPS_MASK _U_(0x00000005) /**< \brief (SUPC_BBPS) MASK Register */ /* -------- SUPC_BKOUT : (SUPC Offset: 0x24) (R/W 32) Backup Output Control -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { struct { uint32_t EN:2; /*!< bit: 0.. 1 Enable Output */ uint32_t :6; /*!< bit: 2.. 7 Reserved */ uint32_t CLR:2; /*!< bit: 8.. 9 Clear Output */ uint32_t :6; /*!< bit: 10..15 Reserved */ uint32_t SET:2; /*!< bit: 16..17 Set Output */ uint32_t :6; /*!< bit: 18..23 Reserved */ uint32_t RTCTGL:2; /*!< bit: 24..25 RTC Toggle Output */ uint32_t :6; /*!< bit: 26..31 Reserved */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_BKOUT_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_BKOUT_OFFSET 0x24 /**< \brief (SUPC_BKOUT offset) Backup Output Control */ #define SUPC_BKOUT_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_BKOUT reset_value) Backup Output Control */ #define SUPC_BKOUT_EN_Pos 0 /**< \brief (SUPC_BKOUT) Enable Output */ #define SUPC_BKOUT_EN_Msk (_U_(0x3) << SUPC_BKOUT_EN_Pos) #define SUPC_BKOUT_EN(value) (SUPC_BKOUT_EN_Msk & ((value) << SUPC_BKOUT_EN_Pos)) #define SUPC_BKOUT_CLR_Pos 8 /**< \brief (SUPC_BKOUT) Clear Output */ #define SUPC_BKOUT_CLR_Msk (_U_(0x3) << SUPC_BKOUT_CLR_Pos) #define SUPC_BKOUT_CLR(value) (SUPC_BKOUT_CLR_Msk & ((value) << SUPC_BKOUT_CLR_Pos)) #define SUPC_BKOUT_SET_Pos 16 /**< \brief (SUPC_BKOUT) Set Output */ #define SUPC_BKOUT_SET_Msk (_U_(0x3) << SUPC_BKOUT_SET_Pos) #define SUPC_BKOUT_SET(value) (SUPC_BKOUT_SET_Msk & ((value) << SUPC_BKOUT_SET_Pos)) #define SUPC_BKOUT_RTCTGL_Pos 24 /**< \brief (SUPC_BKOUT) RTC Toggle Output */ #define SUPC_BKOUT_RTCTGL_Msk (_U_(0x3) << SUPC_BKOUT_RTCTGL_Pos) #define SUPC_BKOUT_RTCTGL(value) (SUPC_BKOUT_RTCTGL_Msk & ((value) << SUPC_BKOUT_RTCTGL_Pos)) #define SUPC_BKOUT_MASK _U_(0x03030303) /**< \brief (SUPC_BKOUT) MASK Register */ /* -------- SUPC_BKIN : (SUPC Offset: 0x28) (R/ 32) Backup Input Control -------- */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef union { struct { uint32_t BKIN:8; /*!< bit: 0.. 7 Backup Input Value */ uint32_t :24; /*!< bit: 8..31 Reserved */ } bit; /*!< Structure used for bit access */ uint32_t reg; /*!< Type used for register access */ } SUPC_BKIN_Type; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ #define SUPC_BKIN_OFFSET 0x28 /**< \brief (SUPC_BKIN offset) Backup Input Control */ #define SUPC_BKIN_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_BKIN reset_value) Backup Input Control */ #define SUPC_BKIN_BKIN_Pos 0 /**< \brief (SUPC_BKIN) Backup Input Value */ #define SUPC_BKIN_BKIN_Msk (_U_(0xFF) << SUPC_BKIN_BKIN_Pos) #define SUPC_BKIN_BKIN(value) (SUPC_BKIN_BKIN_Msk & ((value) << SUPC_BKIN_BKIN_Pos)) #define SUPC_BKIN_MASK _U_(0x000000FF) /**< \brief (SUPC_BKIN) MASK Register */ /** \brief SUPC hardware registers */ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) typedef struct { __IO SUPC_INTENCLR_Type INTENCLR; /**< \brief Offset: 0x00 (R/W 32) Interrupt Enable Clear */ __IO SUPC_INTENSET_Type INTENSET; /**< \brief Offset: 0x04 (R/W 32) Interrupt Enable Set */ __IO SUPC_INTFLAG_Type INTFLAG; /**< \brief Offset: 0x08 (R/W 32) Interrupt Flag Status and Clear */ __I SUPC_STATUS_Type STATUS; /**< \brief Offset: 0x0C (R/ 32) Power and Clocks Status */ __IO SUPC_BOD33_Type BOD33; /**< \brief Offset: 0x10 (R/W 32) BOD33 Control */ __IO SUPC_BOD12_Type BOD12; /**< \brief Offset: 0x14 (R/W 32) BOD12 Control */ __IO SUPC_VREG_Type VREG; /**< \brief Offset: 0x18 (R/W 32) VREG Control */ __IO SUPC_VREF_Type VREF; /**< \brief Offset: 0x1C (R/W 32) VREF Control */ __IO SUPC_BBPS_Type BBPS; /**< \brief Offset: 0x20 (R/W 32) Battery Backup Power Switch */ __IO SUPC_BKOUT_Type BKOUT; /**< \brief Offset: 0x24 (R/W 32) Backup Output Control */ __I SUPC_BKIN_Type BKIN; /**< \brief Offset: 0x28 (R/ 32) Backup Input Control */ } Supc; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ /*@}*/ #endif /* _SAME54_SUPC_COMPONENT_ */