| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some messages that are related to the BVC itself must be forwarded to
the secondary SGSN, too.
This patch implements this for BVC-RESET (BVCI != 0) and FLOW-CONTROL-BVC
messages. The resulting acknowledgement messages from the secondary
SGSN are silently dropped. The idea behind this is that the primary
SGSN is responsible for setting up and maintaining the BVC whereas
the secondary SGSN is rather passive and just has to accept it.
Ticket: OW#1258
Sponsored-by: On-Waves ehf
|
|
This patch modifies gbprox_process_bssgp_ul() to send the message to
the secondary SGSN if the IMSI has matched and routing to the
secondary SGSN is enabled. The destination for stored messages is
modified accordingly.
Ticket: OW#1261
Sponsored-by: On-Waves ehf
|
|
This patch adds a case to test the establishment (and shutdown) of
connection between 2 MS and 2 SGSN, where the assignment is based
on each IMSI. Since BVC-RESET and FLOW-CONTROL-BVC will have to be
sent to both SGSN, an ACK is simulated for both.
New functions to generate FLOW-CONTROL-BVC(-ACK) messages are
provided.
It modifies dump_peers to add the string "IMSI matches" to a TLLI dump
line if appropriate.
Note that there is no real support to use a secondary SGSN in the
gbproxy yet, but the test code reflects the expected behaviour when
the feature is implemented.
Sponsored-by: On-Waves ehf
|
|
Jacob ran the tests with ASAN and noticed that the state is
dead. This is on purpose as we have forced a change in the
transcoding. Re-load the state and verify that it has not
changed in the other cases.
|
|
G729 might not be available, so execute the test with codecs that
are always available.
|
|
To modify or route messages based on the IMSI the latter must be known
when the action shall take place.
This patch modifies the gbproxy to optionally retain and enqueue
messages from the MS while initiating an identification procedure.
Further message processing of the LLC PTP link towards the SGSN will
be done, when the identity of the MS has been acquired.
Note that the N(U) of the LLC GMM SAPI are not adjusted, so it is
possible that adjacent messages of a single LLC link arriving either
at the BSS or the SGSN have the same N(U) and might get discarded,
leading to retransmissions and additional delay.
Note also that retransmissions and packet loss are not yet handled
explicitely. If for instance the generated IDENT REQ gets lost, the
gbproxy will not act on its own. In this case, the MS will time out
and eventually resend the Attach Request on which the gbproxy will
act exactly like before (thus having two Attach Req messages in its
queue, which will both be sent after the Ident Resp arrives).
This has been tested successfully with an E71, needing one
retransmission by the SGSN due to an N(U) collision.
Ticket: OW#1261
Sponsored-by: On-Waves ehf
|
|
This patch copies test_gbproxy_ptmsi_patching to
test_gbproxy_imsi_acquisition as a base for a later test for IMSI
acquisition (which is not yet implemented). The idea behind this is
to make the different behaviour visible in the ok file without
compromising the P-TMSI test.
Sponsored-by: On-Waves ehf
|
|
Currently when patching is enabled and an error happens when
receiving a message from the SGSN, the patched message is sent back
with the PDU_IN_ERROR IE.
This patch modifies gbprox_rx_sig_from_sgsn() to copy the message
before it is patched, so that the original message can be used with
the STATUS message. gbprox_rx_ptp_from_sgsn() does all checks before
the message is patched, so copying is not necessary.
Since gbprox_rx_sig_from_sgsn() is not called for BSSGP UNITDATA
messages and the msgb is already been copied in the gbprox_relay2peer
function, the relative performance impact is expected to be low.
Note that the PDU IE of STATUS messages received from an MS and
forwarded to the SGSN will not be patched. STATUS messages from the
SGSN are only logged and not forwarded to the MS.
Sponsored-by: On-Waves ehf
|
|
Currently messages like these with a TLLI IE (BSSGP) are not
tested (properly) with TLLI patching.
This patch extends the send_bssgp_suspend* functions to accept a
TLLI as argument and adds the send_bssgp_llc_discarded function.
These are then used in test_gbproxy_ptmsi_patching() with a valid
TLLI.
Note that the TLLI IE patching doesn't work currently.
Sponsored-by: On-Waves ehf
|
|
In case we get offered G729 and G711 we might have selected
G729 as the audio codec. The first packet we receive might be
G711 though. In that case we will need to change. But only if
we have a matching alternate codec payload_type. E.g. in the
case of comfort noise we will receive the PT=11 and we don't
want to change.
|
|
In case of some RTP proxy from time to time we are offered both
G729 and G711 but only one of them will work. I intend to adjust
the codec at runtime in case we receive the wrong codec.
|
|
We might be offered multiple codecs by the remote and need to
switch between them once we receive data. Do this by moving it
to a struct so we can separate between proposed and current
codec. In SDP we can have multiple codecs but a global ptime.
The current code doesn't separate that clearly instead we write
it to the main codec.
|
|
The talloc_free on the nat lead to the freeing of the bsc_config
which lead to freeing of the rate_ctr_group. The rate_ctr_group
remained in a global list and the next creation of a bsc_config
would access dead memory. Fix it.
The free routine is only meant to be used by the test, for the
real nat we would need to make sure that all connections and
other state that refers to the cfg is removed/closed first.
Fix various memleaks in the test while we are at it. There are
still some to fix.
==7195== Invalid write of size 4
==7195== at 0x4043171: rate_ctr_group_alloc (linuxlist.h:65)
==7195== by 0x804D893: bsc_config_alloc (bsc_nat_utils.c:174)
==7195== by 0x804B5D2: main (bsc_nat_test.c:954)
==7195== Address 0x4311cbc is 52 bytes inside a block of size 208 free'd
==7195== at 0x4029D28: free (in /usr/lib/valgrind/vgpreload_memcheck-x86-linux.so)
==7195== by 0x4048D98: _talloc_free (talloc.c:609)
==7195== by 0x4052806: talloc_free (talloc.c:578)
==7195== by 0x804B58A: main (bsc_nat_test.c:940)
|
|
Pass -1 to indicate no osmux, before ("b769f3c osmux: add osmux
circuit ID management and resolve NAT problems"), 0 was indicating
no osmux.
|
|
This patch moves the peer related definitions from gb_proxy.c to
gb_proxy_peer.c and adjusts the prefix of each global symbol to
gbproxy_:
Peer definitions (prefix adjusted to gbproxy_):
peer_ctr_description -> gprs/gb_proxy_peer.c (static)
peer_ctrg_desc -> gprs/gb_proxy_peer.c (static)
*peer_by_* -> gprs/gb_proxy_peer.c
gbproxy_peer_alloc -> gprs/gb_proxy_peer.c
gbproxy_peer_free -> gprs/gb_proxy_peer.c
gbprox_cleanup_peers -> gprs/gb_proxy_peer.c
Sponsored-by: On-Waves ehf
|
|
This patch moves several functions and declarations out of gb_proxy.c
to make them reusable by other components and to separate them by
context and task.
Counter enums (prefix is changed to gbproxy_):
enum gbprox_global_ctr -> gprs/gb_proxy.h
enum gbprox_peer_ctr -> gprs/gb_proxy.h
Generic Gb parsing (prefix is changed to gprs_gb_):
struct gbproxy_parse_context -> openbsc/gprs_gb_parse.h
gbprox_parse_dtap() -> gprs/gprs_gb_parse.c
gbprox_parse_llc() -> gprs/gprs_gb_parse.c
gbprox_parse_bssgp() -> gprs/gprs_gb_parse.c
gbprox_log_parse_context() -> gprs/gprs_gb_parse.c
*_shift(), *_match() -> gprs/gprs_gb_parse.c (no prefix)
gbprox_parse_gmm_* -> gprs/gprs_gb_parse.c (static)
gbprox_parse_gsm_* -> gprs/gprs_gb_parse.c (static)
MI testing/parsing (prefix gprs_ added):
is_mi_tmsi() -> gprs/gprs_utils.c
is_mi_imsi() -> gprs/gprs_utils.c
parse_mi_tmsi() -> gprs/gprs_utils.c
TLLI state handling (prefix is changed to gbproxy_):
gbprox_*tlli* -> gprs/gb_proxy_tlli.c
(except gbprox_patch_tlli, gbproxy_make_sgsn_tlli)
Message patching (prefix is changed to gbproxy_):
gbprox_*patch* -> gprs/gb_proxy_patch.c
gbprox_check_imsi -> gprs/gb_proxy_patch.c
Sponsored-by: On-Waves ehf
|
|
Add LLC test messages containing XID (SAPI LLGMM, U frame) and IP traffic
(SAPI LL11, UI frame).
Add a test case containing a complete SGSN session with TLLI/PTMSI
patching enabled.
Sponsored-by: On-Waves ehf
|
|
This patch separates BSS side from SGSN side TLLI/PTMSI tracking. When
TLLI/PTMSI patching is not enabled, the corresponding states shall be
identical. The TLLI/PTMSI state has been moved into the struct
gbproxy_tlli_state and is used twice in gbproxy_tlli_info.
Since the state handling for uplink and downlink messages is
diverging, gbprox_update_state() is replaced by two functions
gbprox_update_state_dl/gbprox_update_state_ul and
gbprox_process_bssgp_message() is replaced by
gbprox_process_bssgp_dl/gbprox_process_bssgp_ul.
Sponsored-by: On-Waves ehf
|
|
This patch adds the functions send_bssgp_ul_unitdata(),
send_bssgp_dl_unitdata(), send_llc_ul_ui(), and send_llc_dl_ui().
They are used instead of send_ns_unitdata() in
test_gbproxy_ra_patching(). This make it easier to modify TLLI, N(U),
and other parameters.
Sponsored-by: On-Waves ehf
|
|
The following parts of the messages have been fixed
- Attach Accept: checksum
- Attach Complete: checksum
- RA Update Accept: Use the same MS Radio Access Capabilities and
DRX Parameters like the other messages
The N(U) of most messages have not been fixed.
Sponsored-by: On-Waves ehf
|
|
Don't replace the current TLLI immediately, store it in an additional
'assigned_tlli' field and discard the old TLLI when both sides have
used the new one (see GSM 04.08, 4.7.1.5).
Add an Attach Complete message to test and check, whether the related
field of the corresponding tlli_info struct are set as expected
during the local TLLI validation cycle.
Sponsored-by: On-Waves ehf
|
|
Currently the enable_patching field in tlli_info is not updated,
when an IMSI is assigned to a TLLI that is already known.
This patch fixes this in gbprox_update_state() after the call to
gbprox_update_tlli_info().
The number of APN increases and the test output file is updated
accordingly.
Sponsored-by: On-Waves ehf
|
|
GSM 24.008 also allows a P-TMSI field in Detach request messages.
This patch adds gbprox_parse_gmm_detach_req() to parse Detach Request
messages which sets the ptmsi field if the IE is present.
In addition, when power_off is set to 1 (MO only), the
invalidate_tlli field is set, since Detach Request message is
expected in this case.
The second detach test (see 'RA update') is modified to use
power_off instead of relying on a Detach Accept from the network.
To make this work, the PTMSI of the RA Update Accept is fixed to
match the TLLI of the Detach Request.
Sponsored-by: On-Waves ehf
|
|
We started with only testing the VTY but now test VTY and CTRL
interface with this python framework and might even extend this
to SMPP. So add and "--enable-external-tests" directive which
enables the external interface tests.
|
|
Add a separate function to clear the IMSI filter to be used instead of
gbprox_set_patch_filter(cfg, NULL, ...). Albeit it fixes a Coverity
issue (Unchecked return value), it is a false positive, since the
return value is always 0 in these cases. Nevertheless it is more
obvious what happens when an explicit clear function is called. Using
NULL as filter argument of gbprox_set_patch_filter still clears the
filter.
Fixes: Coverity CID 1231255
Sponsored-by: On-Waves ehf
|
|
|
|
Adresses:
gbproxy_test.c:1288:17: warning: comparison between signed and
unsigned integer expressions [-Wsign-compare]
Sponsored-by: On-Waves ehf
|
|
This patch modifies the code to pass a pointer to the tlli_info
around once it has been acquired. To achieve this,
gbprox_register_tlli() and gbprox_update_state() are modified to
return it (if it has been found or created), and gbprox_patch_llc(),
gbprox_patch_bssgp(), and gbprox_update_state_after() are modified to
take it as parameter.
Add a new function gbprox_touch_tlli() to update timestamp and list
ordering for existing tlli_infos.
The motivation behind this patch is to make the tlli_info available to
the patching code and to avoid repeated searches for the same TLLI.
Sponsored-by: On-Waves ehf
|
|
This patch adds a combined expiry test to remove one entry by list
length and another by age.
This patch also modifies the existing age based test to register both
TLLI with a different timestamp and to remove only one of the TLLI
entries by age based expiration.
Sponsored-by: On-Waves ehf
|
|
Currently time() is called at several places to control TLLI aging.
Beside calling time() more often than necessary, the decision which
timesource is to be used is coded into the TLLI handling, and testing
complex aging scenarios is cumbersome.
This patch passes the current time as a parameter instead. The call
to time() is moved to gbprox_process_bssgp_message().
Sponsored-by: On-Waves ehf
|
|
This patches removes the call to gbprox_remove_stale_tllis()
from gbprox_register_tlli(), so it must be called explicitly now.
The call is now done from within gbprox_update_state_after().
In addition, the TLLI cache size counter is also kept in sync when
gbprox_remove_stale_tllis is called manually. The call to
gbproxy_peer_free() in gbproxy_peer_free() is moved behind the TLLI
to allow for counter updates in gbprox_delete_tlli().
Sponsored-by: On-Waves ehf
|
|
This adds a test for gbprox_set_patch_filter() and
gbprox_check_imsi().
It also fixes the masking of the type field when IMSIs are checked by
using GSM_MI_TYPE_MASK (0x07) instead of 0x0f.
Sponsored-by: On-Waves ehf
|
|
Currently only TLLIs for which it is known that they may be patched
are put into the TLLI list.
This patch changes this to add TLLIs even when the IMSI is not yet
known. A enable_patching flag is added to the gbproxy_tlli_info
structure to control patching.
Note that this puts every active TLLI into the list where accesses
are O(N) currently.
Sponsored-by: On-Waves ehf
|
|
This adds parsing support for the following messages:
- Attach Request: IMSI/PTMSI
- Identity Response: IMSI/PTMSI
- BSSGP: Optional TLLI IE
- BSSGP/PAGING_PS: PTMSI
A new new_ptmsi_enc field is added for newly assigned PTMSI in
SGSN->BSS messages (instead of ptmsi_enc). The ptmsi_enc field is now
used for informational PTMSI IE in messages.
Sponsored-by: On-Waves ehf
|
|
The given msg array size doesn't match the initializer's size.
Sponsored-by: On-Waves ehf
|
|
This adds a unit test for gbprox_register_tlli() and
gbprox_remove_stale_tllis().
The dump_peers() function is extended by a cfg parameter to support
a non-global gbproxy_config.
Done with Jacob
|
|
Move this patching state into the gbproxy_config as well.
Done by Jacob
|
|
Global state prevents us from writing simple units tests for
single routines. Go through the code and add pointers to the
gbproxy configuration. Only the vty and the test code remain
using the global gbproxy instance.
|
|
Create a testcase for the gprs_str_to_apn and gprs_apn_to_str
routines. While writing the testcase we noticed it is possible to
write more bytes than should have been allowed. This is fixed by
checking that the max_len is at least 1 (needed to write the first
length octet) and to do the size check before writing to the output.
Modify the signature of gprs_str_to_apn to put the length/size next
to the parameter that requires a size.
Done with Jacob
|
|
We intend to move some of these routines to libosmocore but to avoid
a feature symbol clash we are prefixing these routines with gprs_.
Done with Jacob
|
|
The application is called gbproxy but the structures and functions
were inconsistently named as either gbprox or gbproxy. Rename all
structures to use gbproxy.
Done with Jacob
|
|
Done with Jacob
|
|
Create public accessors to the core of the peer to allow to
simplify the test and separate concerns.
Done with Jacob.
|
|
This commit adds code to parse the PTMSI in network originated
messages
- Attach Accept,
- Routing Area Update Accept, and
- P-TMSI Reallocation Command (see below)
to keep track of the TLLI identifying the LLC connection.
The P_TMSI Realloc Command specific code is not being tested yet, so
a corresponding notice is logged when such a message will be
received.
NOTE:
The gbproxy will lose the TLLI when the MS doesn't receive/use
the message (normally the SGSN remembers the old TLLI for some time
to avoid this kind of problem). If this happens the MS will
probably restart the procedure and the network will have to answer
again eventually using one of the above messages which will
re-associate the IMSI with the TLLI before the MS can send a
PDP Context Request message.
Ticket: OW#1192
Sponsored-by: On-Waves ehf
|
|
This adds a set of function that parse a single tlv, lv, tv, or v
encoded information element. They are complementary to the *_put
functions defined in libosmocore's tlv.h file. The functions update
the data and data_len fields unless they are a 'match' function and
the tag field doesn't match.
Sponsored-by: On-Waves ehf
|
|
Currently the enabled_tllis_count field isn't always decremented when
an element is removed from the TLLI cache list.
This patch adds the missing update and also adjusts the counter
accordingly.
Sponsored-by: On-Waves ehf
|
|
Add TLLI cache output to gbprox_dump_peers() to include this info
into the test output.
Separate RA Update Req message handling from Attach Request handling.
Note: There is no test case for the P-TMSI Reallocation Command yet.
Sponsored-by: On-Waves ehf
|
|
This commit adds the following counters:
- attach-reqs: Number of Attach Request messages
- attach-rejs: Number of Attach Reject messages
- tlli-cache: Size of the TLLI cache
Sponsored-by: On-Waves ehf
|
|
This patch adds IMSI/TLLI connection tracking and uses it to control
APN patching based on the IMSI. TLLI entries can expire based on age
and/or by limiting the TLLI list size.
VTY config-gbproxy:
no core-access-point-name disable APN patching
core-access-point-name none remove APN if present
core-access-point-name APN replace APN if present
core-access-point-name none match-imsi RE remove if IMSI matches
core-access-point-name APN match-imsi RE replace if IMSI matches
tlli-list max-age SECONDS expire after SECONDS
no tlli-list max-age don't expire by age
tlli-list max-length N keep N entries only
no tlli-list max-length don't limit list length
RE is an extended regular expression, e.g. ^12345|^23456
Ticket: OW#1192
Sponsored-by: On-Waves ehf
|
|
Currently, all patching state is stored globally in the gbproxy. Thus
the feature cannot be used safely with a concentrating gbproxy (NAT).
This patch moves the state and relevant counters to the gbprox_peer
structure. It adds code to resolve the corresponding peer when
packets are received by looking at BVCI, NSEI, and BSSGP IEs (BVCI,
RAI/LAI/LAC) when the peer is not passed to the
gbprox_patch_bssgp_message() function.
Test cases are also added for the SGSN->BSS case including test cases
with invalid identifiers.
Note that this patch should make it possible to use RAI patching at a
NAT gbproxy as long as the messages are not encrypted.
Ticket: OW#1185
Sponsored-by: On-Waves ehf
|
