Age | Commit message (Collapse) | Author | Files | Lines |
|
Disable large parts of the code that depend on BSC presence.
Don't set msg->lchan nor msg->dst.
Don't use lchan in libmsc.
Decouple lac from bts.
Prepare entry/exit point for MSC -> BSC and MSC -> RNC communication:
Add msc_ifaces.[hc], a_iface.c, with a general msc_tx_dtap() to redirect to
different interfaces depending on the actual subscriber connection.
While iu_tx() is going to be functional fairly soon, the a_tx() is going to be
just a dummy for some time (see comment).
Add Iu specific fields in gsm_subscriber_connection: the UE connection pointer
and an indicator for the Integrity Protection status on Iu (to be fully
implemented in later commits).
Add lac member to gsm_subscriber_connection, to allow decoupling from
bts->location_area_code. The conn->lac will actually be set in iu.c in an
upcoming commit ("add iucs.[hc]").
move to libcommon-cs: gsm48_extract_mi(), gsm48_paging_extract_mi().
libmsc: duplicate gsm0808 / gsm48 functions (towards BSC).
In osmo-nitb, libmsc would directly call the functions on the BSC level, not
always via the bsc_api. When separating libmsc from libbsc, some functions are
missing from the linkage.
Hence duplicate these functions to libmsc, add an msc_ prefix for clarity, also
add a _tx to gsm0808_cipher_mode():
* add msc_gsm0808_tx_cipher_mode() (dummy/stub)
* add msc_gsm48_tx_mm_serv_ack()
* add msc_gsm48_tx_mm_serv_rej()
Call these from libmsc instead of
* gsm0808_cipher_mode()
* gsm48_tx_mm_serv_ack()
* gsm48_tx_mm_serv_rej()
Also add a comment related to msc_gsm0808_tx_cipher_mode() in two places.
Temporarily disable all paging to be able to link libmsc without libbsc.
Skip the paging part of channel_test because the paging is now disabled.
In osmo-nitb, paging is done on BSC level and MSC level "at the same time".
When the new MSC is fully operational, paging will be controlled separately on
the MSC level, and the BSC (RNC) level will be instructed over an IuCS or
A-interface to negotiate paging with the MS (UE). This MSC level paging does
not yet exist and will be added in subsequent commits.
msc_compl_l3(): publish in .h, tweak return value. Use new libmsc enum values
for return val, to avoid dependency on libbsc headers. Make callable from
other scopes: publish in osmo_msc.h and remove 'static' in osmo_msc.c
add gsm_encr to subscr_conn
move subscr_request to gsm_subscriber.h
subscr_request_channel() -> subscr_request_conn()
move to libmsc: osmo_stats_vty_add_cmds()
gsm_04_08: remove apply_codec_restrictions()
gsm0408_test: use NULL for root ctx
move to libbsc: gsm_bts_neighbor()
move to libbsc: lchan_next_meas_rep()
move vty config for t3212 to network level (periodic lu)
remove unneccessary linking from some tests
remove handle_abisip_signal()
abis_rsl.c: don't use libvlr from libbsc
Change-Id: I9cf80f9c2c8a53a29e42f000029e680a9922cb41
|
|
As per TS 23.014, a GSM MSC must implement mobile-originated DTMF
generation. We gate the DTMF signalling messages to MNCC, and expect
the external MNCC handler to deal with it. However, the internal MNCC
handler simply ignored such singalling messages, rather than rejecting
DTMF altogether.
It turns out failure to respond to START DTMF will cause some phones to
behave in interesting ways, particularly with modem
firmware v6.01.00, see https://osmocom.org/issues/1817). In this case
the phone is not able to release the call as the pending response to the
START DTMF is probably keping a reference or lock of some sort.
Change-Id: I336f0cd0a6396b522d228479a417fd4d606157ac
|
|
Change-Id: I651473f638365bbd333c4c80d223cdd023dd2c51
|
|
This provides helpful information for debugging internal MNCC handler.
|
|
When a MNCC handler wants to issue the MNCC_BRIDGE primitive
overt the MNCC interface, this was not possible so far via the
MNCC socket. This primitive was so far only available from the
internal MNCC handler, more or less by accident I suppose. The reason
for this is in the way the array of two call references had been passed
into mncc_tx_to_cc().
|
|
In case of the RTP bridge mode we need to select the codec
ourselves. Rely on the same (incomplete) codec selection that
can be done using the mncc-int configuration node. This might
gain bearer capabilities support.
In case of a SDCCH a TCH/F will be attempted to be assigned.
This is an open issue for both modes and there should be a
preference for full or half-rate channels somewhere.
|
|
In case the default TCH/F codec is "EFR" and we do an early
assignment from SDCCH to a TCH we would assign the TCH/H
codec. This is because the lchan_type will be neither a
TCH/H nor a TCH/F.
At the same time the _gsm48_lchan_modify code to check for
half vs. full-rate is the other way around. Align both.
It is full-rate if it is not a TCH_H. This will have some
other complications down the way (early assignment on
cells with only TCH/H). So the mode should not depend on
the _current_ channel but the kind of channel we want.
|
|
Rename method mncc_rcv_tchf() to mncc_rcv_data(), because the check applies
to all types of data frames, not only TCH/F data.
|
|
Speech codings which are not supported by BTS will be removed from the
bearer capability information element after parsing. This way it is not
required for the MNCC application to consider support of each BTS.
Only GSM full rate is supported by default.
|
|
|
|
This is specified in fifugre 7.10c of 3GPP TS 04.08.
|
|
|
|
In order to have the MNCC application reliably decide on the codec type,
it needs to know if we are running on a TCH/F or TCH/H. Thus, we pass
lchan_mode as a new parameter to the 'struct gsm_mncc'
|
|
These are not needed any more. We used them for u_int
types but we now use uint which comes from stdint.h
|
|
This was done with sed on the files.
|
|
libosmogsm is a new library that is distributed in the libosmocore.
Now, openbsc depends on it. This patch gets openbsc with this
change.
This patch also rewrites all include path to the new
osmocom/[gsm|core]
Signed-off-by: Pablo Neira Ayuso <pablo@gnumonks.org>
|
|
... and make sure tests work again after restructuring
|