1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
|
/************************************************************************************
* configs/vsn/src/vsn.h
* arch/arm/src/board/vsn.n
*
* Copyright (c) 2011 Uros Platise. All rights reserved.
*
* Authors: Uros Platise <uros.platise@isotel.eu>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_VSN_SRC_VSN_INTERNAL_H
#define __CONFIGS_VSN_SRC_VSN_INTERNAL_H
#include <nuttx/config.h>
#include <arch/board/board.h>
#include <nuttx/compiler.h>
#include <stdint.h>
#include "stm32.h"
#include "up_internal.h"
#include "up_arch.h"
/************************************************************************************
* PIN Definitions
************************************************************************************/
/* Board Peripheral Assignment
*
* RS232/Power connector:
* - USART1, is the default bootloader and console
*
* Sensor Connector:
* Digital:
* - GPIOs: PB10, PB11 (or even TIM2 CH3 and CH4)
* - USART3
* - I2C2
* Analog:
* - ADC1
* Supporting Analog Circuitry (not seen outside)
* - RefTap (TIM3_CH3)
* - Power PWM Out (TIM8_CH1 / TIM3_CH1)
* - Filtered Out (TIM3_CH4)
* (TIM8 could run at lower frequency, while TIM3 must run at highest possible)
* - Gain selection muxed with SDcard I/Os.
*
* Radio connector:
* - UART3 / UART4
* - SPI2
* - I2C1 (remapped pins vs. Expansion connector)
* - CAN
* - TIM4 CH[3:4]
*
* Expansion connector:
* - WakeUp Pin
* - System Wide Reset
* - SPI1 is wired to expansion port
* - I2C1
* - USART2 [Rx, Tx, CTS, RTS]
* - DAC [0:1]
* - ADC2 on pins [0:7]
* - TIM2 Channels [1:4]
* - TIM5 Channels [1:4]
*
* Onboard Components:
* - SPI3 has direct connection with FRAM
* - SDCard, conencts the microSD and shares the control lines with Sensor Interface
* to select Amplifier Gain
* - ADC3 is used also for power management (can be shared with ADC1 on sensor connector
* if not used)
*/
/* LED */
#define GPIO_LED (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTB|GPIO_PIN2 |GPIO_OUTPUT_CLEAR)
/* BUTTON - Note that after a good second button causes hardware reset */
#define GPIO_PUSHBUTTON (GPIO_INPUT |GPIO_CNF_INFLOAT |GPIO_MODE_INPUT|GPIO_PORTC|GPIO_PIN5 )
/* Power Management Pins */
#define GPIO_PVS (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTC|GPIO_PIN7 |GPIO_OUTPUT_CLEAR)
#define GPIO_PST (GPIO_INPUT |GPIO_CNF_INPULLDWN|GPIO_MODE_INPUT|GPIO_PORTC|GPIO_PIN13)
#define GPIO_SCTC (GPIO_INPUT |GPIO_CNF_INPULLDWN|GPIO_MODE_INPUT|GPIO_PORTA|GPIO_PIN8 )
#define GPIO_PCLR (GPIO_INPUT |GPIO_CNF_INPULLDWN|GPIO_MODE_INPUT|GPIO_PORTD|GPIO_PIN1 ) // by default this pin is OSCOUT, requires REMAP
#define GPIO_XPWR (GPIO_INPUT |GPIO_CNF_INFLOAT |GPIO_MODE_INPUT|GPIO_PORTC|GPIO_PIN4 )
/* FRAM (alt pins are not listed here and are a part of SPI) */
#define GPIO_FRAM_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_50MHz|GPIO_PORTA|GPIO_PIN15|GPIO_OUTPUT_SET)
/* Sensor Interface */
#define GPIO_GP1_HIZ (GPIO_INPUT |GPIO_CNF_INFLOAT |GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN10)
#define GPIO_GP1_PUP (GPIO_INPUT |GPIO_CNF_INPULLUP |GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN10)
#define GPIO_GP1_PDN (GPIO_INPUT |GPIO_CNF_INPULLDWN|GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN10)
#define GPIO_GP1_LOW (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTB|GPIO_PIN10|GPIO_OUTPUT_CLEAR)
#define GPIO_GP1_HIGH (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTB|GPIO_PIN10|GPIO_OUTPUT_SET)
#define GPIO_GP2_HIZ (GPIO_INPUT |GPIO_CNF_INFLOAT |GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN11)
#define GPIO_GP2_PUP (GPIO_INPUT |GPIO_CNF_INPULLUP |GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN11)
#define GPIO_GP2_PDN (GPIO_INPUT |GPIO_CNF_INPULLDWN|GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN11)
#define GPIO_GP2_LOW (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTB|GPIO_PIN11|GPIO_OUTPUT_CLEAR)
#define GPIO_GP2_HIGH (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTB|GPIO_PIN11|GPIO_OUTPUT_SET)
#define GPIO_OPA_INPUT (GPIO_INPUT |GPIO_CNF_ANALOGIN |GPIO_MODE_INPUT|GPIO_PORTC|GPIO_PIN0 )
#define GPIO_OPA_ENABLE (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTC|GPIO_PIN1 |GPIO_OUTPUT_CLEAR)
#define GPIO_OPA_REFAIN (GPIO_INPUT |GPIO_CNF_ANALOGIN |GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN0 )
#define GPIO_OPA_REFPWM (GPIO_ALT |GPIO_CNF_AFPP |GPIO_MODE_50MHz|GPIO_PORTB|GPIO_PIN0 )
#define GPIO_OUT_PWRON (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTC|GPIO_PIN6 |GPIO_OUTPUT_CLEAR)
#define GPIO_OUT_PWROFF (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTC|GPIO_PIN6 |GPIO_OUTPUT_SET)
#define GPIO_OUT_PWRPWM (GPIO_ALT |GPIO_CNF_AFPP |GPIO_MODE_10MHz|GPIO_PORTC|GPIO_PIN6 )
#define GPIO_OUT_PWRPWM_TIM8_CH 1 /* TIM8.CH1 */
#define GPIO_OUT_HIZ (GPIO_INPUT |GPIO_CNF_INFLOAT |GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN1 )
#define GPIO_OUT_PUP (GPIO_INPUT |GPIO_CNF_INPULLUP |GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN1 )
#define GPIO_OUT_PDN (GPIO_INPUT |GPIO_CNF_INPULLDWN|GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN1 )
#define GPIO_OUT_LOW (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTB|GPIO_PIN1 |GPIO_OUTPUT_CLEAR)
#define GPIO_OUT_HIGH (GPIO_OUTPUT|GPIO_CNF_OUTPP |GPIO_MODE_2MHz |GPIO_PORTB|GPIO_PIN1 |GPIO_OUTPUT_SET)
#define GPIO_OUT_AIN (GPIO_INPUT |GPIO_CNF_ANALOGIN |GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN1 )
#define GPIO_OUT_PWM (GPIO_ALT |GPIO_CNF_AFPP |GPIO_MODE_10MHz|GPIO_PORTB|GPIO_PIN1 )
#define GPIO_OUT_PWM_TIM3_CH 4 /* TIM3.CH4 */
/* Radio Connector */
/* Expansion Connector */
/************************************************************************************
* Debugging
************************************************************************************/
#ifdef CONFIG_CPP_HAVE_VARARGS
# ifdef CONFIG_DEBUG
# define message(...) lib_lowprintf(__VA_ARGS__)
# else
# define message(...) printf(__VA_ARGS__)
# endif
#else
# ifdef CONFIG_DEBUG
# define message lib_lowprintf
# else
# define message printf
# endif
#endif
/************************************************************************************
* Public data
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Public Functions
************************************************************************************/
/************************************************************************************
* Name: stm32_spiinitialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the VSN board.
*
************************************************************************************/
extern void weak_function stm32_spiinitialize(void);
/************************************************************************************
* Name: stm32_usbinitialize
*
* Description:
* Called to setup USB-related GPIO pins for the VSN board.
*
************************************************************************************/
extern void weak_function stm32_usbinitialize(void);
/************************************************************************************
* Init Power Module and set board system voltage
************************************************************************************/
extern void board_power_init(void);
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_VSN_SRC_VSN_INTERNAL_H */
|
