diff options
Diffstat (limited to 'nuttx/configs/pic32-starterkit/nsh/defconfig')
| -rw-r--r-- | nuttx/configs/pic32-starterkit/nsh/defconfig | 803 |
1 files changed, 2 insertions, 801 deletions
diff --git a/nuttx/configs/pic32-starterkit/nsh/defconfig b/nuttx/configs/pic32-starterkit/nsh/defconfig index ff7c056edc..e0843ff876 100644 --- a/nuttx/configs/pic32-starterkit/nsh/defconfig +++ b/nuttx/configs/pic32-starterkit/nsh/defconfig @@ -33,52 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip family. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# NOTE: The PIC32MX is always little endian. -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_NOINTC - define if the architecture does not -# support an interrupt controller or otherwise cannot support -# APIs like up_enable_irq() and up_disable_irq(). -# CONFIG_ARCH_VECNOTIRQ - Usually the interrupt vector number provided -# to interfaces like irq_attach() and irq_detach are the same as IRQ -# numbers that are provied to IRQ management functions like -# up_enable_irq() and up_disable_irq(). But that is not true for all -# interrupt controller implementations. For example, the PIC32MX -# interrupt controller manages interrupt sources that have a many-to-one -# relationship to interrupt vectors. In such cases, CONFIG_ARCH_VECNOTIRQ -# must defined so that the OS logic will know not to assume it can use -# a vector number to enable or disable interrupts. -# CONFIG_ARCH_IRQPRIO - The PIC32MX supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="mips" CONFIG_ARCH_MIPS=y @@ -116,7 +71,7 @@ CONFIG_PIC32MX_MICROCHIPW_LITE=y CONFIG_PIC32MX_MICROCHIPL_LITE=n # -# Individual subsystems can be enabled: +# Individual subsystems can be enabled: # CONFIG_PIC32MX_WDT=n @@ -175,28 +130,6 @@ CONFIG_PIC32MX_IOPORTG=y # # PIC32MX Configuration Settings # -# DEVCFG0: -# CONFIG_PIC32MX_DEBUGGER - Background Debugger Enable. Default 3 (disabled). The -# value 2 enables. -# CONFIG_PIC32MX_ICESEL - In-Circuit Emulator/Debugger Communication Channel Select -# Default 1 (PG2) -# CONFIG_PIC32MX_PROGFLASHWP - Program FLASH write protect. Default 0xff (disabled) -# CONFIG_PIC32MX_BOOTFLASHWP - Default 1 (disabled) -# CONFIG_PIC32MX_CODEWP - Default 1 (disabled) -# DEVCFG1: (All settings determined by selections in board.h) -# DEVCFG2: (All settings determined by selections in board.h) -# DEVCFG3: -# CONFIG_PIC32MX_USBIDO - USB USBID Selection. Default 1 if USB enabled -# (USBID pin is controlled by the USB module), but 0 (GPIO) otherwise. -# CONFIG_PIC32MX_VBUSIO - USB VBUSON Selection (Default 1 if USB enabled -# (VBUSON pin is controlled by the USB module, but 0 (GPIO) otherwise. -# CONFIG_PIC32MX_WDENABLE - Enabled watchdog on power up. Default 0 (watchdog -# can be enabled later by software). -# CONFIG_PIC32MX_FETHIO: Ethernet I/O Pin Selection bit. 1 (or undefined)= -# Default Ethernet I/O Pins; 0=Alternate Ethernet I/O Pins -# CONFIG_PIC32MX_FMIIEN: Ethernet MII Enable bit. 1 (or undefined) = MII -# enabled; 0=RMII enabled -# CONFIG_PIC32MX_DEBUGGER=2 CONFIG_PIC32MX_ICESEL=1 CONFIG_PIC32MX_FETHIO=0 @@ -205,17 +138,6 @@ CONFIG_PIC32MX_FMIIEN=0 # # PIC32MX specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART1_SERIAL_CONSOLE=y CONFIG_UART2_SERIAL_CONSOLE=n CONFIG_UART3_SERIAL_CONSOLE=n @@ -268,35 +190,6 @@ CONFIG_UART6_2STOP=0 # # PIC32MX specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects the Micrel KS8721 PHY -# CONFIG_PHY_DP83848C - Selects the National Semiconduction DP83848C PHY -# CONFIG_PHY_LAN8720 - Selects the SMSC LAN8720 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 2 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 4 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets. -# Also needs CONFIG_DEBUG. -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. Automatically enables CONFIG_NET_DESCDEBUG as well. -# CONFIG_NET_DESCDEBUG - Enabled low level descriptor debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_DUMPPACKET - Dump all incoming and output packet contents. -# Also needs CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# -# Related DEVCFG3 Configuration Settings: -# CONFIG_PIC32MX_FETHIO: Ethernet I/O Pin Selection bit. 1 (or undefined)= -# Default Ethernet I/O Pins; 0=Alternate Ethernet I/O Pins -# CONFIG_PIC32MX_FMIIEN: Ethernet MII Enable bit. 1 (or undefined) = MII -# enabled; 0=RMII enabled -# CONFIG_PHY_KS8721=n CONFIG_PHY_DP83848C=y CONFIG_PHY_LAN8720=n @@ -318,19 +211,6 @@ CONFIG_PIC32MX_USBDEV_BDTDEBUG=n # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -340,99 +220,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_HAVE_CXX - Enable support for C++ -# CONFIG_HAVE_CXXINITIALIZE - The platform-specific logic includes support -# for initialization of static C++ instances for this architecture -# and for the selected toolchain (via up_cxxinitialize()). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# CONFIG_SCHED_WAITPID - Enable the waitpid() API -# CONFIG_SCHED_ATEXIT - Enabled the atexit() API -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n @@ -473,27 +260,6 @@ CONFIG_SCHED_ATEXIT=n # # System Logging # -# CONFIG_SYSLOG - Enables the System Logging feature. -# CONFIG_RAMLOG - Enables the RAM logging feature -# CONFIG_RAMLOG_CONSOLE - Use the RAM logging device as a system console. -# If this feature is enabled (along with CONFIG_DEV_CONSOLE), then all -# console output will be re-directed to a circular buffer in RAM. This -# is useful, for example, if the only console is a Telnet console. Then -# in that case, console output from non-Telnet threads will go to the -# circular buffer and can be viewed using the NSH 'dmesg' command. -# CONFIG_RAMLOG_SYSLOG - Use the RAM logging device for the syslogging -# interface. If this feature is enabled (along with CONFIG_SYSLOG), -# then all debug output (only) will be re-directed to the circular -# buffer in RAM. This RAM log can be view from NSH using the 'dmesg' -# command. -# CONFIG_RAMLOG_NPOLLWAITERS - The number of threads than can be waiting -# for this driver on poll(). Default: 4 -# -# If CONFIG_RAMLOG_CONSOLE or CONFIG_RAMLOG_SYSLOG is selected, then the -# following may also be provided: -# -# CONFIG_RAMLOG_CONSOLE_BUFSIZE - Size of the console RAM log. Default: 1024 -# CONFIG_SYSLOG=n CONFIG_RAMLOG=n @@ -505,16 +271,6 @@ CONFIG_RAMLOG_SYSLOG=n # # Settings for NXFLAT # -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals -# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and -# CONFIG_DEBUG_BINFMT have to be defined or -# CONFIG_NXFLAT_DUMPBUFFER does nothing. -# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table -# is ordered by symbol name -# CONFIG_NXFLAT=n CONFIG_NXFLAT_DUMPBUFFER=n CONFIG_SYMTAB_ORDEREDBYNAME=y @@ -546,9 +302,6 @@ CONFIG_DISABLE_POLL=y # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -571,46 +324,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_STDIO_LINEBUFFER - If standard C buffered I/O is enabled -# (CONFIG_STDIO_BUFFER_SIZE > 0), then this option may be added -# to force automatic, line-oriented flushing the output buffer -# for putc(), fputc(), putchar(), puts(), fputs(), printf(), -# fprintf(), and vfprintf(). When a newline is encountered in -# the output string, the output buffer will be flushed. This -# (slightly) increases the NuttX footprint but supports the kind -# of behavior that people expect for printf(). -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 @@ -638,46 +351,6 @@ CONFIG_FB_HWCURSORIMAGE=n # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=y CONFIG_FAT_LCNAMES=y CONFIG_FAT_LFN=y @@ -688,13 +361,6 @@ CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -702,65 +368,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_NOINTS -- CONFIG_NET_NOINT indicates that uIP not called from -# the interrupt level. If CONFIG_NET_NOINTS is defined, critical sections -# will be managed with semaphores; Otherwise, it assumed that uIP will be -# called from interrupt level handling and critical sections will be -# managed by enabling and disabling interrupts. -# CONFIG_NET_MULTIBUFFER - Traditionally, uIP has used a single buffer -# for all incoming and outgoing traffic. If this configuration is -# selected, then the driver can manage multiple I/O buffers and can, -# for example, be filling one input buffer while sending another -# output buffer. Or, as another example, the driver may support -# queuing of concurrent input/ouput and output transfers for better -# performance. -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=n CONFIG_NET_NOINTS=n @@ -791,8 +410,6 @@ CONFIG_NET_MULTICAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -800,45 +417,12 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # FTP Server # -# CONFIG_FTPD_VENDORID - The vendor name to use in FTP communications. -# Default: "NuttX" -# CONFIG_FTPD_SERVERID - The server name to use in FTP communications. -# Default: "NuttX FTP Server" -# CONFIG_FTPD_CMDBUFFERSIZE - The maximum size of one command. Default: -# 128 bytes. -# CONFIG_FTPD_DATABUFFERSIZE - The size of the I/O buffer for data -# transfers. Default: 512 bytes. -# CONFIG_FTPD_WORKERSTACKSIZE - The stacksize to allocate for each -# FTP daemon worker thread. Default: 2048 bytes. -# -# Other required configuration settings: Of course TCP networking support -# is required. But here are a couple that are less obvious: -# -# CONFIG_DISABLE_PTHREAD - pthread support is required -# CONFIG_DISABLE_POLL - poll() support is required -# CONFIG_FTPD_CMDBUFFERSIZE=512 CONFIG_FTPD_DATABUFFERSIZE=2048 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -851,26 +435,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -887,54 +451,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB serial device class driver (Standard CDC ACM class) # -# CONFIG_CDCACM -# Enable compilation of the USB serial driver -# CONFIG_CDCACM_CONSOLE -# Configures the CDC/ACM serial port as the console device. -# CONFIG_CDCACM_EP0MAXPACKET -# Endpoint 0 max packet size. Default 64 -# CONFIG_CDCACM_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation. Default 2. -# CONFIG_CDCACM_EPINTIN_FSSIZE -# Max package size for the interrupt IN endpoint if full speed mode. -# Default 64. -# CONFIG_CDCACM_EPINTIN_HSSIZE -# Max package size for the interrupt IN endpoint if high speed mode. -# Default 64 -# CONFIG_CDCACM_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_CDCACM_EPBULKOUT_FSSIZE -# Max package size for the bulk OUT endpoint if full speed mode. -# Default 64. -# CONFIG_CDCACM_EPBULKOUT_HSSIZE -# Max package size for the bulk OUT endpoint if high speed mode. -# Default 512. -# CONFIG_CDCACM_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# CONFIG_CDCACM_EPBULKIN_FSSIZE -# Max package size for the bulk IN endpoint if full speed mode. -# Default 64. -# CONFIG_CDCACM_EPBULKIN_HSSIZE -# Max package size for the bulk IN endpoint if high speed mode. -# Default 512. -# CONFIG_CDCACM_NWRREQS and CONFIG_CDCACM_NRDREQS -# The number of write/read requests that can be in flight. -# Default 256. -# CONFIG_CDCACM_VENDORID and CONFIG_CDCACM_VENDORSTR -# The vendor ID code/string. Default 0x0525 and "NuttX" -# 0x0525 is the Netchip vendor and should not be used in any -# products. This default VID was selected for compatibility with -# the Linux CDC ACM default VID. -# CONFIG_CDCACM_PRODUCTID and CONFIG_CDCACM_PRODUCTSTR -# The product ID code/string. Default 0xa4a7 and "CDC/ACM Serial" -# 0xa4a7 was selected for compatibility with the Linux CDC ACM -# default PID. -# CONFIG_CDCACM_RXBUFSIZE and CONFIG_CDCACM_TXBUFSIZE -# Size of the serial receive/transmit buffers. Default 256. -# CONFIG_CDCACM=n CONFIG_CDCACM_CONSOLE=n #CONFIG_CDCACM_EP0MAXPACKET @@ -959,26 +475,6 @@ CONFIG_CDCACM_CONSOLE=n # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=1 @@ -997,112 +493,6 @@ CONFIG_USBMSC_REMOVABLE=y # # Graphics related configuration settings # -# CONFIG_NX -# Enables overall support for graphics library and NX -# CONFIG_NX_MULTIUSER -# Configures NX in multi-user mode -# CONFIG_NX_NPLANES -# Some YUV color formats requires support for multiple planes, -# one for each color component. Unless you have such special -# hardware, this value should be undefined or set to 1 -# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP, -# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP, -# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and -# CONFIG_NX_DISABLE_32BPP -# NX supports a variety of pixel depths. You can save some -# memory by disabling support for unused color depths. -# CONFIG_NX_PACKEDMSFIRST -# If a pixel depth of less than 8-bits is used, then NX needs -# to know if the pixels pack from the MS to LS or from LS to MS -# CONFIG_NX_LCDDRIVER -# By default, NX builds to use a framebuffer driver (see -# include/nuttx/fb.h). If this option is defined, NX will -# build to use an LCD driver (see include/nuttx/lcd/lcd.h). -# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device. -# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device. -# CONFIG_NX_MOUSE -# Build in support for mouse input -# CONFIG_NX_KBD -# Build in support of keypad/keyboard input -# CONFIG_NXTK_BORDERWIDTH -# Specifies with with of the border (in pixels) used with -# framed windows. The default is 4. -# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2 -# Specify the colors of the border used with framed windows. -# CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so -# is normally darker. The default is medium and dark grey, -# respectively -# CONFIG_NXTK_AUTORAISE -# If set, a window will be raised to the top if the mouse position -# is over a visible portion of the window. Default: A mouse -# button must be clicked over a visible portion of the window. -# CONFIG_NXFONTS_CHARBITS -# The number of bits in the character set. Current options are -# only 7 and 8. The default is 7. -# CONFIG_NXFONT_SANS17X22 -# This option enables support for a tiny, 17x22 san serif font -# (font ID FONTID_SANS17X22 == 14). -# CONFIG_NXFONT_SANS20X26 -# This option enables support for a tiny, 20x26 san serif font -# (font ID FONTID_SANS20X26 == 15). -# CONFIG_NXFONT_SANS23X27 -# This option enables support for a tiny, 23x27 san serif font -# (font ID FONTID_SANS23X27 == 1). -# CONFIG_NXFONT_SANS22X29 -# This option enables support for a small, 22x29 san serif font -# (font ID FONTID_SANS22X29 == 2). -# CONFIG_NXFONT_SANS28X37 -# This option enables support for a medium, 28x37 san serif font -# (font ID FONTID_SANS28X37 == 3). -# CONFIG_NXFONT_SANS39X48 -# This option enables support for a large, 39x48 san serif font -# (font ID FONTID_SANS39X48 == 4). -# CONFIG_NXFONT_SANS17X23B -# This option enables support for a tiny, 17x23 san serif bold font -# (font ID FONTID_SANS17X23B == 16). -# CONFIG_NXFONT_SANS20X27B -# This option enables support for a tiny, 20x27 san serif bold font -# (font ID FONTID_SANS20X27B == 17). -# CONFIG_NXFONT_SANS22X29B -# This option enables support for a small, 22x29 san serif bold font -# (font ID FONTID_SANS22X29B == 5). -# CONFIG_NXFONT_SANS28X37B -# This option enables support for a medium, 28x37 san serif bold font -# (font ID FONTID_SANS28X37B == 6). -# CONFIG_NXFONT_SANS40X49B -# This option enables support for a large, 40x49 san serif bold font -# (font ID FONTID_SANS40X49B == 7). -# CONFIG_NXFONT_SERIF22X29 -# This option enables support for a small, 22x29 font (with serifs) -# (font ID FONTID_SERIF22X29 == 8). -# CONFIG_NXFONT_SERIF29X37 -# This option enables support for a medium, 29x37 font (with serifs) -# (font ID FONTID_SERIF29X37 == 9). -# CONFIG_NXFONT_SERIF38X48 -# This option enables support for a large, 38x48 font (with serifs) -# (font ID FONTID_SERIF38X48 == 10). -# CONFIG_NXFONT_SERIF22X28B -# This option enables support for a small, 27x38 bold font (with serifs) -# (font ID FONTID_SERIF22X28B == 11). -# CONFIG_NXFONT_SERIF27X38B -# This option enables support for a medium, 27x38 bold font (with serifs) -# (font ID FONTID_SERIF27X38B == 12). -# CONFIG_NXFONT_SERIF38X49B -# This option enables support for a large, 38x49 bold font (with serifs) -# (font ID FONTID_SERIF38X49B == 13). -# -# NX Multi-user only options: -# -# CONFIG_NX_BLOCKING -# Open the client message queues in blocking mode. In this case, -# nx_eventhandler() will not return until a message is received and processed. -# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS -# Specifies the maximum number of messages that can fit in -# the message queues. No additional resources are allocated, but -# this can be set to prevent flooding of the client or server with -# too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many -# messages are pre-allocated). -# CONFIG_NX=n CONFIG_NX_MULTIUSER=n CONFIG_NX_NPLANES=1 @@ -1155,19 +545,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest # -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) -# CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n CONFIG_EXAMPLE_NETTEST_NOMAC=y @@ -1186,39 +563,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for apps/nshlib # -# CONFIG_NSH_BUILTIN_APPS - Support external registered, -# "named" applications that can be executed from the NSH -# command line (see apps/README.txt for more information). -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_BUILTIN_APPS=y CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n @@ -1255,14 +599,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # I2C tool settings # -# CONFIG_I2CTOOL_BUILTIN - Build the tools as an NSH built-in command -# CONFIG_I2CTOOL_MINBUS - Smallest bus index supported by the hardware (default 0). -# CONFIG_I2CTOOL_MAXBUS - Largest bus index supported by the hardware (default 3) -# CONFIG_I2CTOOL_MINADDR - Minium device address (default: 0x03) -# CONFIG_I2CTOOL_MAXADDR - Largest device address (default: 0x77) -# CONFIG_I2CTOOL_MAXREGADDR - Largest register address (default: 0xff) -# CONFIG_I2CTOOL_DEFFREQ - Default frequency (default: 1000000) -# CONFIG_I2CTOOL_BUILTIN=y CONFIG_I2CTOOL_MINBUS=1 CONFIG_I2CTOOL_MAXBUS=4 @@ -1274,45 +610,10 @@ CONFIG_I2CTOOL_DEFFREQ=100000 # # Settings for examples/ftpd # -# CONFIG_EXAMPLES_FTPD_PRIO - Priority of the FTP daemon. -# Default: SCHED_PRIORITY_DEFAULT -# CONFIG_EXAMPLES_FTPD_STACKSIZE - Stack size allocated for the -# FTP daemon. Default: 2048 -# CONFIG_EXAMPLES_FTPD_NONETINIT - Define to suppress configuration of the -# network by apps/examples/ftpd. You would need to suppress network -# configuration if the network is configuration prior to running the -# example. -# -# NSH always initializes the network so if CONFIG_NSH_BUILTIN_APPS is -# defined, so is CONFIG_EXAMPLES_FTPD_NONETINIT (se it does not explicitly -# need to be defined in that case): -# -# CONFIG_NSH_BUILTIN_APPS - Build the FTPD daemon example test as an -# NSH built-in function. By default the FTPD daemon will be built -# as a standalone application. -# -# If CONFIG_EXAMPLES_FTPD_NONETINIT is not defined, then the following may -# be specified to customized the network configuration: -# -# CONFIG_EXAMPLE_FTPD_NOMAC - If the hardware has no MAC address of its -# own, define this =y to provide a bogus address for testing. -# CONFIG_EXAMPLE_FTPD_IPADDR - The target IP address. Default 10.0.0.2 -# CONFIG_EXAMPLE_FTPD_DRIPADDR - The default router address. Default -# 10.0.0.1 -# CONFIG_EXAMPLE_FTPD_NETMASK - The network mask. Default: 255.255.255.0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -1327,40 +628,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Settings for examples/usbstorage # -# CONFIG_EXAMPLES_USBMSC_BUILTIN -# Build the USBMSC storage example as an NSH built-in application. -# CONFIG_EXAMPLES_USBMSC_NLUNS -# Defines the number of logical units (LUNs) exported by the USB storage -# driver. Each LUN corresponds to one exported block driver (or partition -# of a block driver). May be 1, 2, or 3. Default is 1. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR1 -# The minor device number of the block driver for the first LUN. For -# example, N in /dev/mmcsdN. Used for registering the block driver. Default -# is zero. -# CONFIG_EXAMPLES_USBMSC_DEVPATH1 -# The full path to the registered block driver. Default is "/dev/mmcsd0" -# CONFIG_EXAMPLES_USBMSC_DEVMINOR2 and CONFIG_EXAMPLES_USBMSC_DEVPATH2 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 2 or 3. No defaults. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR3 and CONFIG_EXAMPLES_USBMSC_DEVPATH3 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 3. No defaults. -# -# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then -# the example code will also manage the USB trace output. The amount of trace output -# can be controlled using: -# -# CONFIG_EXAMPLES_USBMSC_TRACEINIT -# Show initialization events -# CONFIG_EXAMPLES_USBMSC_TRACECLASS -# Show class driver events -# CONFIG_EXAMPLES_USBMSC_TRACETRANSFERS -# Show data transfer events -# CONFIG_EXAMPLES_USBMSC_TRACECONTROLLER -# Show controller events -# CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS -# Show interrupt-related events. -# CONFIG_EXAMPLES_USBMSC_BUILTIN=y CONFIG_EXAMPLES_USBMSC_NLUNS=1 CONFIG_EXAMPLES_USBMSC_DEVMINOR1=0 @@ -1374,33 +641,6 @@ CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS=n # # Settings for examples/usbterm # -# CONFIG_EXAMPLES_USBTERM_BUILTIN - Build the usbterm example as an NSH -# built-in command. NOTE: This is not fully functional as of this -# writing.. It should work, but there is no mechanism in place yet -# to exit the USB terminal program and return to NSH. -# CONFIG_EXAMPLES_USBTERM_DEVINIT - If defined, then the example will -# call a user provided function as part of its initialization: -# int usbterm_devinit(void); -# And another user provided function at termination: -# void usbterm_devuninit(void); -# CONFIG_EXAMPLES_USBTERM_BUFLEN - The size of the input and output -# buffers used for receiving data. Default 256 bytes. -# -# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB, or -# CONFIG_USBDEV_TRACE), then the example code will also manage the USB trace -# output. The amount of trace output can be controlled using: -# -# CONFIG_EXAMPLES_USBTERM_TRACEINIT -# Show initialization events -# CONFIG_EXAMPLES_USBTERM_TRACECLASS -# Show class driver events -# CONFIG_EXAMPLES_USBTERM_TRACETRANSFERS -# Show data transfer events -# CONFIG_EXAMPLES_USBTERM_TRACECONTROLLER -# Show controller events -# CONFIG_EXAMPLES_USBTERM_TRACEINTERRUPTS -# Show interrupt-related events. -# CONFIG_EXAMPLES_USBTERM_BUILTIN=y CONFIG_EXAMPLES_USBTERM_DEVINIT=y #CONFIG_EXAMPLES_USBTERM_BUFLEN @@ -1415,25 +655,6 @@ CONFIG_EXAMPLES_USBTERM_TRACEINTERRUPTS=n # # Configuration prequisites: # -# CONFIG_USBDEV=y : USB device support must be enabled -# CONFIG_CDCACM=y : The CDC/ACM driver must be built -# CONFIG_NSH_BUILTIN_APPS : NSH built-in application support must be enabled -# -# Configuration options specific to this example: -# -# CONFIG_EXAMPLES_CDCACM_DEVMINOR -# The minor number of the CDC/ACM device. -# CONFIG_EXAMPLES_CDCACM_TRACEINIT -# Show initialization events -# CONFIG_EXAMPLES_CDCACM_TRACECLASS -# Show class driver events -# CONFIG_EXAMPLES_CDCACM_TRACETRANSFERS -# Show data transfer events -# CONFIG_EXAMPLES_CDCACM_TRACECONTROLLER -# Show controller events -# CONFIG_EXAMPLES_CDCACM_TRACEINTERRUPTS -# Show interrupt-related events. -# CONFIG_EXAMPLES_CDCACM_DEVMINOR=0 CONFIG_EXAMPLES_CDCACM_TRACEINIT=n CONFIG_EXAMPLES_CDCACM_TRACECLASS=n @@ -1444,26 +665,6 @@ CONFIG_EXAMPLES_CDCACM_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the PIC32MX which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n |