; ; MGCP Configuration for Asterisk ; [general] ;port = 2427 ;bindaddr = 0.0.0.0 ; See qos.tex or Quality of Service section of asterisk.pdf for a description of these parameters. ;tos=cs3 ; Sets TOS for signaling packets. ;tos_audio=ef ; Sets TOS for RTP audio packets. ;cos=3 ; Sets 802.1p priority for signaling packets. ;cos_audio=5 ; Sets 802.1p priority for RTP audio packets. ;------------------------------ JITTER BUFFER CONFIGURATION -------------------------- ; jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of a ; MGCP channel. Defaults to "no". An enabled jitterbuffer will ; be used only if the sending side can create and the receiving ; side can not accept jitter. The MGCP channel can accept jitter, ; thus an enabled jitterbuffer on the receive MGCP side will only ; be used if the sending side can create jitter and jbforce is ; also set to yes. ; jbforce = no ; Forces the use of a jitterbuffer on the receive side of a MGCP ; channel. Defaults to "no". ; jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds. ; jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is ; resynchronized. Useful to improve the quality of the voice, with ; big jumps in/broken timestamps, usually sent from exotic devices ; and programs. Defaults to 1000. ; jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of a MGCP ; channel. Two implementations are currently available - "fixed" ; (with size always equals to jbmax-size) and "adaptive" (with ; variable size, actually the new jb of IAX2). Defaults to fixed. ; jbtargetextra = 40 ; This option only affects the jb when 'jbimpl = adaptive' is set. ; The option represents the number of milliseconds by which the new ; jitter buffer will pad its size. the default is 40, so without ; modification, the new jitter buffer will set its size to the jitter ; value plus 40 milliseconds. increasing this value may help if your ; network normally has low jitter, but occasionally has spikes. ; jblog = no ; Enables jitterbuffer frame logging. Defaults to "no". ;----------------------------------------------------------------------------------- ;[dlinkgw] ;host = 192.168.0.64 ;context = default ;directmedia = no ;line => aaln/2 ;line => aaln/1 ;; The MGCP channel supports the following service codes: ;; # - Transfer ;; *67 - Calling Number Delivery Blocking ;; *70 - Cancel Call Waiting ;; *72 - Call Forwarding Activation ;; *73 - Call Forwarding Deactivation ;; *78 - Do Not Disturb Activation ;; *79 - Do Not Disturb Deactivation ;; *8 - Call pick-up ; ; known to work with Swissvoice IP10s ;[192.168.1.20] ;context=local ;host=192.168.1.20 ;callerid = "John Doe" <123> ;callgroup=0 ; in the range from 0 to 63 ;pickupgroup=0 ; in the range from 0 to 63 ;nat=no ;threewaycalling=yes ;transfer=yes ; transfer requires threewaycalling=yes. Use FLASH to transfer ;callwaiting=yes ; this might be a cause of trouble for ip10s ;cancallforward=yes ;line => aaln/1 ; ;[dph100] ; ; Supporting the DPH100M requires defining DLINK_BUGGY_FIRMWARE in ; chan_mgcp.c in addition to enabling the slowsequence mode due to ; bugs in the D-Link firmware ; ;context=local ;host=dynamic ;dtmfmode=none ; DTMF Mode can be 'none', 'rfc2833', or 'inband' or ; 'hybrid' which starts in none and moves to inband. Default is none. ;slowsequence=yes ; The DPH100M does not follow MGCP standards for sequencing ;line => aaln/1 ; known to work with wave7optics FTTH LMGs ;[192.168.1.20] ;accountcode = 1000 ; record this in cdr as account identification for billing ;amaflags = billing ; record this in cdr as flagged for 'billing', ; 'documentation', or 'omit' ;context = local ;host = 192.168.1.20 ;wcardep = aaln/* ; enables wildcard endpoint and sets it to 'aaln/*' ; another common format is '*' ;callerid = "Duane Cox" <123> ; now lets setup line 1 using per endpoint configuration... ;callwaiting = no ;callreturn = yes ;cancallforward = yes ;directmedia = no ;transfer = no ;dtmfmode = inband ;line => aaln/1 ; now lets save this config to line1 aka aaln/1 ;callerid = "Duane Cox" <456> ; now lets setup line 2 ;callwaiting = no ;callreturn = yes ;cancallforward = yes ;directmedia = no ;transfer = no ;dtmfmode = inband ;line => aaln/2 ; now lets save this config to line2 aka aaln/2