diff options
Diffstat (limited to 'trunk/configs/rpt.conf.sample')
| -rw-r--r-- | trunk/configs/rpt.conf.sample | 193 |
1 files changed, 193 insertions, 0 deletions
diff --git a/trunk/configs/rpt.conf.sample b/trunk/configs/rpt.conf.sample new file mode 100644 index 000000000..6aee784dc --- /dev/null +++ b/trunk/configs/rpt.conf.sample @@ -0,0 +1,193 @@ +; Radio Repeater / Remote Base configuration file (for use with app_rpt) +; As of app_rpt version 0.39, 12/20/2005 +; + +;[000] ; Node ID of first repeater + +;rxchannel = Zap/1 ; Rx audio/signalling channel +; Note: if you use a unified interface (tx/rx on one channel), only +; specify the rxchannel and the txchannel will be assumed from the rxchannel +;txchannel = Zap/2 ; Tx audio/signalling channel +;duplex = 2 ; (Optional) set duplex operating mode +;; 0 = half duplex (telemetry and courtesy tones do not transmit) +;; 1 = semi-half duplex (telemetry and courtesy tones transmit, but not +;; repeated audio +;; 2 = normal full-duplex mode (Default) +;; 3 = full-duplex mode, without repeated audio from main input source +;functions = functions-repeater ; DTMF function list +;; specify this for a different function list then local when on link +;;link_functions = functions-different ; DTMF function list for link +;;phone_functions = functions-phone ; (optional) different functions for 'P' mode +;;dphone_functions = functions-dphone ; (optional) different functions for 'D' mode +;;nodes = nodes-different ; (optional) different node list +;tonezone = us ; use US tones (default) +;context = default ; dialing context for phone +;callerid = "WB6NIL Repeater" <(213) 555-0123> ; Callerid for phone calls +;idrecording = wb6nil ; id recording +;accountcode=RADIO ; account code (optional) +;funcchar = * ; function lead-in character (defaults to '*') +;endchar = # ; command mode end character (defaults to '#') +;;nobusyout=yes ; (optional) Do not busy-out reverse-patch when + ; normal patch in use +;hangtime=1000 ; squelch tail hang time (in ms) (optional) +;totime=100000 ; transmit time-out time (in ms) (optional) +;idtime=30000 ; id interval time (in ms) (optional) +;politeid=30000 ; time in milliseconds before ID timer + ; expires to try and ID in the tail. + ; (optional, default is 30000). +;idtalkover=|iwb6nil/rpt ; Talkover ID (optional) default is none +;unlinkedct=ct2 ; unlinked courtesy tone (optional) default is none + +;; The tailmessagetime,tailsquashedtime, and tailmessages need to be set +;; to support tail messages. They can be omitted otherwise. +;tailmessagetime=300000 ; Play a tail message every 5 mins +;tailsquashedtime=30000 ; If squashed by another user, +;; try again after 30 seconds +;tailmessages=msg1,msg2,msg3 ;list of messages to be played for tail message + +; The default values for hangtime, time-out time, and id interval time are +; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms) +; respectively + +;[001] ; Node ID of first repeater + +;rxchannel = Zap/3 ; Rx audio/signalling channel +; Note: if you use a unified interface (tx/rx on one channel), only +; specify the rxchannel and the txchannel will be assumed from the rxchannel +;txchannel = Zap/4 ; Tx audio/signalling channel +;functions = functions-repeater ; DTMF function list +;; specify this for a different function list then local when on link +;;link_functions = functions-different ; DTMF function list for link +;;phone_functions = functions-phone ; (optional) different functions for 'P' mode +;;dphone_functions = functions-dphone ; (optional) different functions for 'D' mode +;;nodes = nodes-different ; (optional) different node list +;tonezone = us ; use US tones (default) +;context = default ; dialing context for phone +;callerid = "WB6NIL Repeater" <(213) 555-0123> ; Callerid for phone calls +;idrecording = wb6nil ; id recording +;accountcode=RADIO ; account code (optional) +;funcchar = * ; function lead-in character (defaults to '*') +;endchar = # ; command mode end character (defaults to '#') +;;nobusyout=yes ; (optional) Do not busy-out reverse-patch when + ; normal patch in use +;hangtime=1000 ; squelch tail hang time (in ms) (optional) +;totime=100000 ; transmit time-out time (in ms) (optional) +;idtime=30000 ; id interval time (in ms) (optional) +;politeid=30000 ; time in milliseconds before ID timer + ; expires to try and ID in the tail. + ; (optional, default is 30000). +;idtalkover=|iwb6nil/rpt ; Talkover ID (optional) default is none +;unlinkedct=ct2 ; unlinked courtesy tone (optional) default is none + +;[002] ; Node ID of remote base + +;rxchannel = Zap/5 ; Rx audio/signalling channel +; Note: if you use a unified interface (tx/rx on one channel), only +; specify the rxchannel and the txchannel will be assumed from the rxchannel +;txchannel = Zap/6 ; Tx audio/signalling channel +;functions = functions-remote +;remote = ft897 ; Set remote=y for dumb remote or + ; remote=ft897 for Yaesu FT-897 or + ; remote=rbi for Doug Hall RBI1 +;iobase = 0x378 ; Specify IO port for parallel port (optional) + +;[functions-repeater] +;1=ilink,1 ; Specific link disconnect +;2=ilink,2 ; Specific Link connect - monitor only +;3=ilink,3 ; Specific Link connect - transceive +;4=ilink,4 ; Enter command mode on a specific link +;7=ilink,5 ; Link status +;;XX=ilink,6 ; Disconnect all links (not used here) + +;80=status,1 ; System info +;81=status,2 ; Time +;82=status,3 ; app_rpt.c Version + +;6=autopatchup ; Autopatch up +;0=autopatchdn ; Autopatch down + +;90=cop,1 ; System warm boot +;91=cop,2 ; System enable +;92=cop,3 ; System disable + +;[functions-remote] + +;0=remote,1 ; Retrieve Memory +;1=remote,2 ; Set freq. +;2=remote,3 ; Set Rx PL tone. +;40=remote,100 ; Rx PL off +;41=remote,101 ; Rx PL on +;42=remote,102 ; Tx PL off +;43=remote,103 ; Tx PL on +;44=remote,104 ; Low Pwr +;45=remote,105 ; Med Pwr +;46=remote,106 ; Hi Pwr +;5=remote,5 ; Status + +;[telemetry] + +; Telemetry entries are shared across all repeaters +; Can be a tone sequence, morse string, or a file +; +; |t - Tone escape sequence +; +; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) +; Single frequencies are created by setting freq1 or freq2 to zero. +; +; |m - Morse escape sequence +; +; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the +; [morse] section. +; +; Follow with an alphanumeric string +; +; |i - Morse ID escape sequence +; +; Sends Morse code at the ID amplitude and ID frequency as defined in the +; [morse] section. +; +; Follow with an alphanumeric string + + +;ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) +;ct2=|t(660,880,150,2048) +;ct3=|t(440,0,150,2048) +;ct4=|t(550,0,150,2048) +;ct5=|t(660,0,150,2048) +;ct6=|t(880,0,150,2048) +;ct7=|t(660,440,150,2048) +;ct8=|t(700,1100,150,2048) +;remotetx=|t(2000,0,75,2048)(0,0,75,0)(1600,0,75,2048); +;remotemon=|t(1600,0,75,2048) +;cmdmode=|t(900,903,200,2048) +;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) + + +;[morse] + +;speed=20 ; Approximate speed in WPM +;frequency=800 ; Morse Telemetry Frequency +;amplitude=4096 ; Morse Telemetry Amplitude +;idfrequency=330 ; Morse ID Frequency +;idamplitude=2048 ; Morse ID Amplitude + +;[nodes] + +;000 = context_A@foo.bar.com/1234,foo.bar.com +;001 = context_B@baz.waldo.com/4321,baz.waldo.com +;002 = context_C@pepper.salt.com/5678,pepper.salt.com,y ; this is a remote + +;of course, you can also specify these with domain names, but why rely +;on DNS working unnecessarily? + +;[memory] + +;; this example gives you 146.460, simplex, 100.0 HZ PL, hi-power, transmit PL +;00 = 146.460,100.0,sht +;; this example gives you 146.940, minus offset, 100.0 HZ PL, low-power, no PL +;01 = 146.940,100.0,-l + +; The format for these entries is: Receive-Freq,Receive-PL,Attrbutes +; Attributes: l=low power, m=medium power, h=high power, -=minus offset, +; s=simplex, +=plus offset, t=tx PL enable, r=rx PL enable + |