diff options
Diffstat (limited to 'trunk/configs/misdn.conf.sample')
| -rw-r--r-- | trunk/configs/misdn.conf.sample | 455 |
1 files changed, 455 insertions, 0 deletions
diff --git a/trunk/configs/misdn.conf.sample b/trunk/configs/misdn.conf.sample new file mode 100644 index 000000000..65bdda3ea --- /dev/null +++ b/trunk/configs/misdn.conf.sample @@ -0,0 +1,455 @@ +; +; chan_misdn sample config +; + +; general section: +; +; for debugging and general setup, things that are not bound to port groups +; + +[general] +; +; Sets the Path to the misdn-init.conf (for nt_ptp mode checking) +; +misdn_init=/etc/misdn-init.conf + +; set debugging flag: +; 0 - No Debug +; 1 - mISDN Messages and * - Messages, and * - State changes +; 2 - Messages + Message specific Informations (e.g. bearer capability) +; 3 - very Verbose, the above + lots of Driver specific infos +; 4 - even more Verbose than 3 +; +; default value: 0 +; +debug=0 + + + +; set debugging file and flags for mISDNuser (NT-Stack) +; +; flags can be or'ed with the following values: +; +; DBGM_NET 0x00000001 +; DBGM_MSG 0x00000002 +; DBGM_FSM 0x00000004 +; DBGM_TEI 0x00000010 +; DBGM_L2 0x00000020 +; DBGM_L3 0x00000040 +; DBGM_L3DATA 0x00000080 +; DBGM_BC 0x00000100 +; DBGM_TONE 0x00000200 +; DBGM_BCDATA 0x00000400 +; DBGM_MAN 0x00001000 +; DBGM_APPL 0x00002000 +; DBGM_ISDN 0x00004000 +; DBGM_SOCK 0x00010000 +; DBGM_CONN 0x00020000 +; DBGM_CDATA 0x00040000 +; DBGM_DDATA 0x00080000 +; DBGM_SOUND 0x00100000 +; DBGM_SDATA 0x00200000 +; DBGM_TOPLEVEL 0x40000000 +; DBGM_ALL 0xffffffff +; + +ntdebugflags=0 +ntdebugfile=/var/log/misdn-nt.log + + +; some pbx systems do cut the L1 for some milliseconds, to avoid +; dropping running calls, we can set this flag to yes and tell +; mISDNuser not to drop the calls on L2_RELEASE +ntkeepcalls=no + +; the big trace +; +; default value: [not set] +; +;tracefile=/var/log/asterisk/misdn.log + + +; set to yes if you want mISDN_dsp to bridge the calls in HW +; +; default value: yes +; +bridging=no + + +; +; watches the L1s of every port. If one l1 is down it tries to +; get it up. The timeout is given in seconds. with 0 as value it +; does not watch the l1 at all +; +; default value: 0 +; +; this option is only read at loading time of chan_misdn, +; which means you need to unload and load chan_misdn to change the +; value, an asterisk restart should do the trick +; +l1watcher_timeout=0 + +; stops dialtone after getting first digit on nt Port +; +; default value: yes +; +stop_tone_after_first_digit=yes + +; whether to append overlapdialed Digits to Extension or not +; +; default value: yes +; +append_digits2exten=yes + +;;; CRYPTION STUFF + +; Whether to look for dynamic crypting attempt +; +; default value: no +; +dynamic_crypt=no + +; crypt_prefix, what is used for crypting Protocol +; +; default value: [not set] +; +crypt_prefix=** + +; Keys for cryption, you reference them in the dialplan +; later also in dynamic encr. +; +; default value: [not set] +; +crypt_keys=test,muh + +; users sections: +; +; name your sections as you which but not "general" ! +; the sections are Groups, you can dial out in extensions.conf +; with Dial(mISDN/g:extern/101) where extern is a section name, +; chan_misdn tries every port in this section to find a +; new free channel +; + +; The default section is not a group section, it just contains config elements +; which are inherited by group sections. +; + +;------------------------------ JITTER BUFFER CONFIGURATION -------------------------- +; jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of a + ; SIP channel. Defaults to "no". An enabled jitterbuffer will + ; be used only if the sending side can create and the receiving + ; side can not accept jitter. The SIP channel can accept jitter, + ; thus a jitterbuffer on the receive SIP side will be used only + ; if it is forced and enabled. + +; jbforce = no ; Forces the use of a jitterbuffer on the receive side of a SIP + ; channel. Defaults to "no". + +; jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds. + +; jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is + ; resynchronized. Useful to improve the quality of the voice, with + ; big jumps in/broken timestamps, usually sent from exotic devices + ; and programs. Defaults to 1000. + +; jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of a SIP + ; channel. Two implementations are currently available - "fixed" + ; (with size always equals to jbmaxsize) and "adaptive" (with + ; variable size, actually the new jb of IAX2). Defaults to fixed. + +; jblog = no ; Enables jitterbuffer frame logging. Defaults to "no". +;----------------------------------------------------------------------------------- + +[default] + +; define your default context here +; +; default value: default +; +context=misdn + +; language +; +; default value: en +; +language=en + +; +; sets the musiconhold class +; +musicclass=default + +; +; Either if we should produce DTMF Tones ourselves +; +senddtmf=yes + +; +; If we should generate Ringing for chan_sip and others +; +far_alerting=no + + +; +; here you can define which bearers should be allowed +; +allowed_bearers=all + +; Prefixes for national and international, those are put before the +; oad if an according dialplan is set by the other end. +; +; default values: nationalprefix : 0 +; internationalprefix : 00 +; +nationalprefix=0 +internationalprefix=00 + +; set rx/tx gains between -8 and 8 to change the RX/TX Gain +; +; default values: rxgain: 0 +; txgain: 0 +; +rxgain=0 +txgain=0 + +; some telcos especially in NL seem to need this set to yes, also in +; switzerland this seems to be important +; +; default value: no +; +te_choose_channel=no + + + +; +; This option defines, if chan_misdn should check the L1 on a PMP +; before making a group call on it. The L1 may go down for PMP Ports +; so we might need this. +; But be aware! a broken or plugged off cable might be used for a group call +; as well, since chan_misdn has no chance to distinguish if the L1 is down +; because of a lost Link or because the Provider shut it down... +; +; default: no +; +pmp_l1_check=no + + +; +; in PMP this option defines which cause should be sent out to +; the 3. caller. chan_misdn does not support callwaiting on TE +; PMP side. This allows to modify the RELEASE_COMPLETE cause +; at least. +; +reject_cause=16 + + +; +; Send Setup_Acknowledge on incoming calls anyway (instead of PROCEEDING), +; this requests additional Infos, so we can waitfordigits +; without much issues. This works only for PTP Ports +; +; default value: no +; +need_more_infos=no + + +; +; set this to yes if you want to disconnect calls when a timeout occurs +; for example during the overlapdial phase +; +nttimeout=no + +; set the method to use for channel selection: +; standard - always choose the first free channel with the lowest number +; round_robin - use the round robin algorithm to select a channel. use this +; if you want to balance your load. +; +; default value: standard +; +method=standard + + +; specify if chan_misdn should collect digits before going into the +; dialplan, you can choose yes=4 Seconds, no, or specify the amount +; of seconds you need; +; +overlapdial=yes + +; +; dialplan means Type Of Number in ISDN Terms (for outgoing calls) +; +; there are different types of the dialplan: +; +; dialplan -> outgoing Number +; localdialplan -> callerid +; cpndialplan -> connected party number +; +; dialplan options: +; +; 0 - unknown +; 1 - International +; 2 - National +; 4 - Subscriber +; +; This setting is used for outgoing calls +; +; default value: 0 +; +dialplan=0 +localdialplan=0 +cpndialplan=0 + + + +; +; turn this to no if you don't mind correct handling of Progress Indicators +; +early_bconnect=yes + + +; +; turn this on if you like to send Tone Indications to a Incoming +; isdn channel on a TE Port. Rarely used, only if the Telco allows +; you to send indications by yourself, normally the Telco sends the +; indications to the remote party. +; +; default: no +; +incoming_early_audio=no + +; uncomment the following to get into s extension at extension conf +; there you can use DigitTimeout if you can't or don't want to use +; isdn overlap dial. +; note: This will jump into the s exten for every exten! +; +; default value: no +; +;always_immediate=no + +; +; set this to yes if you want to generate your own dialtone +; with always_immediate=yes, else chan_misdn generates the dialtone +; +; default value: no +; +nodialtone=no + + +; uncomment the following if you want callers which called exactly the +; base number (so no extension is set) jump to the s extension. +; if the user dials something more it jumps to the correct extension +; instead +; +; default value: no +; +;immediate=no + +; uncomment the following to have hold and retrieve support +; +; default value: no +; +;hold_allowed=yes + +; Pickup and Callgroup +; +; default values: not set = 0 +; range: 0-63 +; +;callgroup=1 +;pickupgroup=1 + + +; +; these are the exact isdn screening and presentation indicators +; if -1 is given for both values the presentation indicators are used +; from asterisks SetCallerPres application. +; s=0, p=0 -> callerid presented not screened +; s=1, p=1 -> callerid presented but screened (the remote end does not see it!) +; +; default values s=-1, p=-1 +presentation=-1 +screen=-1 + +; this enables echocancellation, with the given number of taps +; be aware, move this setting only to outgoing portgroups! +; A value of zero turns echocancellation off. +; +; possible values are: 0,32,64,128,256,yes(=128),no(=0) +; +; default value: no +; +;echocancel=no + +; Set this to no to disable echotraining. You can enter a number > 10 +; the value is a multiple of 0.125 ms. +; +; default value: no +; yes = 2000 +; no = 0 +; +echotraining=no + +; +; chan_misdns jitterbuffer, default 4000 +; +jitterbuffer=4000 + +; +; change this threshold to enable dejitter functionality +; +jitterbuffer_upper_threshold=0 + + +; +; change this to yes, if you want to bridge a mISDN data channel to +; another channel type or to an application. +; +hdlc=no + + +; +; defines the maximum amount of incoming calls per port for +; this group. Calls which exceed the maximum will be marked with +; the channel variable MAX_OVERFLOW. It will contain the amount of +; overflowed calls +; +max_incoming=-1 + +; +; defines the maximum amount of outgoing calls per port for this group +; exceeding calls will be rejected +; +max_outgoing=-1 + +[intern] +; define your ports, e.g. 1,2 (depends on mISDN-driver loading order) +ports=1,2 +; context where to go to when incoming Call on one of the above ports +context=Intern + +[internPP] +; +; adding the postfix 'ptp' to a port number is obsolete now, chan_misdn +; parses /etc/misdn-init.conf and sets the ptp mode to the corresponding +; configs. For backwards compatibility you can still set ptp here. +; +ports=3 + +[first_extern] +; again port defs +ports=4 +; again a context for incoming calls +context=Extern1 +; msns for te ports, listen on those numbers on the above ports, and +; indicate the incoming calls to asterisk +; here you can give a comma separated list or simply an '*' for +; any msn. +msns=* + +; here an example with given msns +[second_extern] +ports=5 +context=Extern2 +callerid=15 +msns=102,144,101,104 |