diff options
Diffstat (limited to 'configs/rpt.conf.sample')
-rwxr-xr-x | configs/rpt.conf.sample | 116 |
1 files changed, 104 insertions, 12 deletions
diff --git a/configs/rpt.conf.sample b/configs/rpt.conf.sample index 1d0a568a0..1439e5b21 100755 --- a/configs/rpt.conf.sample +++ b/configs/rpt.conf.sample @@ -7,18 +7,24 @@ ; Note: if you use a unified interface (tx/rx on one channel), only ; specify the rxchannel and the txchannel will be assumed from the rxchannel ;txchannel = Zap/2 ; Tx audio/signalling channel +;functions = functions-repeater ; DTMF function list +;; specify this for a different function list then local when on link +;;link_functions = functions-different ; DTMF function list for link ;tonezone = us ; use US tones (default) -;simple = no ; Not in "simple" mode ;context = default ; dialing context for phone ;callerid = "WB6NIL Repeater" <(559) 692-1234> ; Callerid for phone calls ;idrecording = wb6nil ; id recording ;accountcode=RADIO ; account code (optional) +;funcchar = * ; function lead-in character (defaults to '*') +;endchar = # ; command mode end character (defaults to '#') ;hangtime=1000 ; squelch tail hang time (in ms) (optional) ;totime=100000 ; transmit time-out time (in ms) (optional) ;idtime=30000 ; id interval time (in ms) (optional) -politeid=30000 ; time in milliseconds before ID timer +;politeid=30000 ; time in milliseconds before ID timer ; expires to try and ID in the tail. ; (optional, default is 30000). +;idtalkover=|iwb6nil/rpt ; Talkover ID (optional) default is none +;unlinkedct=ct2 ; unlinked courtesy tone (optional) default is none ; The default values for hangtime, time-out time, and id interval time are ; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms) @@ -31,14 +37,20 @@ politeid=30000 ; time in milliseconds before ID timer ; specify the rxchannel and the txchannel will be assumed from the rxchannel ;txchannel = Zap/4 ; Tx audio/signalling channel ;tonezone = us ; use US tones (default) -;simple = no ; Not in "simple" mode ;context = default ; dialing context for phone ;callerid = "WB6NIL Repeater" <(559) 692-1234> ; Callerid for phone calls ;idrecording = wb6nil ; id recording ;accountcode=RADIO ; account code (optional) +;funcchar = * ; function lead-in character (defaults to '*') +;endchar = # ; command mode end character (defaults to '#') ;hangtime=1000 ; squelch tail hang time (in ms) (optional) ;totime=100000 ; transmit time-out time (in ms) (optional) ;idtime=30000 ; id interval time (in ms) (optional) +;politeid=30000 ; time in milliseconds before ID timer + ; expires to try and ID in the tail. + ; (optional, default is 30000). +;idtalkover=|iwb6nil/rpt ; Talkover ID (optional) default is none +;unlinkedct=ct2 ; unlinked courtesy tone (optional) default is none ;[002] ; Node ID of remote base @@ -46,26 +58,106 @@ politeid=30000 ; time in milliseconds before ID timer ; Note: if you use a unified interface (tx/rx on one channel), only ; specify the rxchannel and the txchannel will be assumed from the rxchannel ;txchannel = Zap/6 ; Tx audio/signalling channel +;functions = functions-remote ;remote = yes ;iobase = 0x378 ; Specify IO port for parallel port (optional) -[nodes] +;[functions-repeater] +;1=ilink,1 ; Specific link disconnect +;2=ilink,2 ; Specific Link connect - monitor only +;3=ilink,3 ; Specific Link connect - transceive +;4=ilink,4 ; Enter command mode on a specific link +;7=ilink,5 ; Link status +;;XX=ilink,6 ; Disconnect all links (not used here) + +;80=status,1 ; System info +;81=status,2 ; Time +;82=status,3 ; app_rpt.c Version + +;6=autopatchup ; Autopatch up +;0=autopatchdn ; Autopatch down + +;90=cop,1 ; System warm boot +;91=cop,2 ; System enable +;92=cop,3 ; System disable + +;[functions-remote] -000 = context_A@1.2.3.4/1234 -001 = context_B@5.6.7.8/4321 +;0=remote,1 ; Retrieve Memory +;1=remote,2 ; Set freq. +;2=remote,3 ; Set Rx PL tone. +;40=remote,100 ; Rx PL off +;41=remote,101 ; Rx PL on +;42=remote,102 ; Tx PL off +;43=remote,103 ; Tx PL on +;44=remote,104 ; Low Pwr +;45=remote,105 ; Med Pwr +;46=remote,106 ; Hi Pwr +;5=remote,5 ; Status + +;[telemetry] + +; Telemetry entries are shared across all repeaters +; Can be a tone sequence, morse string, or a file +; +; |t - Tone escape sequence +; +; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) +; Single frequencies are created by setting freq1 or freq2 to zero. +; +; |m - Morse escape sequence +; +; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the +; [morse] section. +; +; Follow with an alphanumeric string +; +; |i - Morse ID escape sequence +; +; Sends Morse code at the ID amplitude and ID frequency as defined in the +; [morse] section. +; +; Follow with an alphanumeric string + + +;ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) +;ct2=|t(660,880,150,2048) +;ct3=|t(440,0,150,2048) +;ct4=|t(550,0,150,2048) +;ct5=|t(660,0,150,2048) +;ct6=|t(880,0,150,2048) +;ct7=|t(660,440,150,2048) +;ct8=|t(700,1100,150,2048) +;remotetx=|t(2000,0,75,2048)(0,0,75,0)(1600,0,75,2048); +;remotemon=|t(1600,0,75,2048) +;cmdmode=|t(900,903,200,2048) +;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) + + +;[morse] + +;speed=20 ; Approximate speed in WPM +;frequency=800 ; Morse Telemetry Frequency +;amplitude=4096 ; Morse Telemetry Amplitude +;idfrequency=330 ; Morse ID Frequency +;idamplitude=2048 ; Morse ID Amplitude + +;[nodes] + +;000 = context_A@1.2.3.4/1234 +;001 = context_B@5.6.7.8/4321 ;of course, you can also specify these with domain names, but why rely ;on DNS working unnecessarily? -[memory] +;[memory] -; this example gives you 146.460, simplex, 100.0 HZ PL, hi-power, transmit PL -00 = 146.460,100.0,sht -; this example gives you 146.940, minus offset, 100.0 HZ PL, low-power, no PL -01 = 146.940,100.0,-l +;; this example gives you 146.460, simplex, 100.0 HZ PL, hi-power, transmit PL +;00 = 146.460,100.0,sht +;; this example gives you 146.940, minus offset, 100.0 HZ PL, low-power, no PL +;01 = 146.940,100.0,-l ; The format for these entries is: Receive-Freq,Receive-PL,Attrbutes ; Attributes: l=low power, m=medium power, h=high power, -=minus offset, ; s=simplex, +=plus offset, t=tx PL enable, r=rx PL enable - |