diff options
Diffstat (limited to '1.4.23-rc4/configs/extensions.conf.sample')
-rw-r--r-- | 1.4.23-rc4/configs/extensions.conf.sample | 614 |
1 files changed, 0 insertions, 614 deletions
diff --git a/1.4.23-rc4/configs/extensions.conf.sample b/1.4.23-rc4/configs/extensions.conf.sample deleted file mode 100644 index b7151f4c4..000000000 --- a/1.4.23-rc4/configs/extensions.conf.sample +++ /dev/null @@ -1,614 +0,0 @@ -; extensions.conf - the Asterisk dial plan -; -; Static extension configuration file, used by -; the pbx_config module. This is where you configure all your -; inbound and outbound calls in Asterisk. -; -; This configuration file is reloaded -; - With the "dialplan reload" command in the CLI -; - With the "reload" command (that reloads everything) in the CLI - -; -; The "General" category is for certain variables. -; -[general] -; -; If static is set to no, or omitted, then the pbx_config will rewrite -; this file when extensions are modified. Remember that all comments -; made in the file will be lost when that happens. -; -; XXX Not yet implemented XXX -; -static=yes -; -; if static=yes and writeprotect=no, you can save dialplan by -; CLI command "dialplan save" too -; -writeprotect=no -; -; If autofallthrough is set, then if an extension runs out of -; things to do, it will terminate the call with BUSY, CONGESTION -; or HANGUP depending on Asterisk's best guess. This is the default. -; -; If autofallthrough is not set, then if an extension runs out of -; things to do, Asterisk will wait for a new extension to be dialed -; (this is the original behavior of Asterisk 1.0 and earlier). -; -;autofallthrough=no -; -; If clearglobalvars is set, global variables will be cleared -; and reparsed on an extensions reload, or Asterisk reload. -; -; If clearglobalvars is not set, then global variables will persist -; through reloads, and even if deleted from the extensions.conf or -; one of its included files, will remain set to the previous value. -; -; NOTE: A complication sets in, if you put your global variables into -; the AEL file, instead of the extensions.conf file. With clearglobalvars -; set, a "reload" will often leave the globals vars cleared, because it -; is not unusual to have extensions.conf (which will have no globals) -; load after the extensions.ael file (where the global vars are stored). -; So, with "reload" in this particular situation, first the AEL file will -; clear and then set all the global vars, then, later, when the extensions.conf -; file is loaded, the global vars are all cleared, and then not set, because -; they are not stored in the extensions.conf file. -; -clearglobalvars=no -; -; If priorityjumping is set to 'yes', then applications that support -; 'jumping' to a different priority based on the result of their operations -; will do so (this is backwards compatible behavior with pre-1.2 releases -; of Asterisk). Individual applications can also be requested to do this -; by passing a 'j' option in their arguments. -; -;priorityjumping=yes -; -; User context is where entries from users.conf are registered. The -; default value is 'default' -; -;userscontext=default -; -; You can include other config files, use the #include command -; (without the ';'). Note that this is different from the "include" command -; that includes contexts within other contexts. The #include command works -; in all asterisk configuration files. -;#include "filename.conf" - -; The "Globals" category contains global variables that can be referenced -; in the dialplan with the GLOBAL dialplan function: -; ${GLOBAL(VARIABLE)} -; ${${GLOBAL(VARIABLE)}} or ${text${GLOBAL(VARIABLE)}} or any hybrid -; Unix/Linux environmental variables can be reached with the ENV dialplan -; function: ${ENV(VARIABLE)} -; -[globals] -CONSOLE=Console/dsp ; Console interface for demo -;CONSOLE=Zap/1 -;CONSOLE=Phone/phone0 -IAXINFO=guest ; IAXtel username/password -;IAXINFO=myuser:mypass -TRUNK=Zap/G2 ; Trunk interface -; -; Note the 'G2' in the TRUNK variable above. It specifies which group (defined -; in chan_dahdi.conf) to dial, i.e. group 2, and how to choose a channel to use in -; the specified group. The four possible options are: -; -; g: select the lowest-numbered non-busy Zap channel -; (aka. ascending sequential hunt group). -; G: select the highest-numbered non-busy Zap channel -; (aka. descending sequential hunt group). -; r: use a round-robin search, starting at the next highest channel than last -; time (aka. ascending rotary hunt group). -; R: use a round-robin search, starting at the next lowest channel than last -; time (aka. descending rotary hunt group). -; -TRUNKMSD=1 ; MSD digits to strip (usually 1 or 0) -;TRUNK=IAX2/user:pass@provider - -; -; Any category other than "General" and "Globals" represent -; extension contexts, which are collections of extensions. -; -; Extension names may be numbers, letters, or combinations -; thereof. If an extension name is prefixed by a '_' -; character, it is interpreted as a pattern rather than a -; literal. In patterns, some characters have special meanings: -; -; X - any digit from 0-9 -; Z - any digit from 1-9 -; N - any digit from 2-9 -; [1235-9] - any digit in the brackets (in this example, 1,2,3,5,6,7,8,9) -; . - wildcard, matches anything remaining (e.g. _9011. matches -; anything starting with 9011 excluding 9011 itself) -; ! - wildcard, causes the matching process to complete as soon as -; it can unambiguously determine that no other matches are possible -; -; For example the extension _NXXXXXX would match normal 7 digit dialings, -; while _1NXXNXXXXXX would represent an area code plus phone number -; preceded by a one. -; -; Each step of an extension is ordered by priority, which must -; always start with 1 to be considered a valid extension. The priority -; "next" or "n" means the previous priority plus one, regardless of whether -; the previous priority was associated with the current extension or not. -; The priority "same" or "s" means the same as the previously specified -; priority, again regardless of whether the previous entry was for the -; same extension. Priorities may be immediately followed by a plus sign -; and another integer to add that amount (most useful with 's' or 'n'). -; Priorities may then also have an alias, or label, in -; parenthesis after their name which can be used in goto situations -; -; Contexts contain several lines, one for each step of each -; extension, which can take one of two forms as listed below, -; with the first form being preferred. -; -;[context] -;exten => someexten,{priority|label{+|-}offset}[(alias)],application(arg1,arg2,...) -;exten => someexten,{priority|label{+|-}offset}[(alias)],application,arg1|arg2... -; -; Included Contexts -; -; One may include another context in the current one as well, optionally with a -; date and time. Included contexts are included in the order -; they are listed. -; The reason a context would include other contexts is for their -; extensions. -; The algorithm to find an extension is recursive, and works in this -; fashion: -; first, given a stack on which to store context references, -; push the context to find the extension onto the stack... -; a) Try to find a matching extension in the context at the top of -; the stack, and, if found, begin executing the priorities -; there in sequence. -; b) If not found, Search the switches, if any declared, in -; sequence. -; c) If still not found, for each include, push that context onto -; the top of the context stack, and recurse to a). -; d) If still not found, pop the entry from the top of the stack; -; if the stack is empty, the search has failed. If it's not, -; continue with the next context in c). -; This is a depth-first traversal, and stops with the first context -; that provides a matching extension. As usual, if more than one -; pattern in a context will match, the 'best' match will win. -; Please note that that extensions found in an included context are -; treated as if they were in the context from which the search began. -; The PBX's notion of the "current context" is not changed. -; Please note that in a context, it does not matter where an include -; directive occurs. Whether at the top, or near the bottom, the effect -; will be the same. The only thing that matters is that if there is -; more than one include directive, they will be searched for extensions -; in order, first to last. -; Also please note that pattern matches (like _9XX) are not treated -; any differently than exact matches (like 987). Also note that the -; order of extensions in a context have no affect on the outcome. -; -; Timing list for includes is -; -; <time range>|<days of week>|<days of month>|<months> -; -; Note that ranges may be specified to wrap around the ends. Also, minutes are -; fine-grained only down to the closest even minute. -; -;include => daytime|9:00-17:00|mon-fri|*|* -;include => weekend|*|sat-sun|*|* -;include => weeknights|17:02-8:58|mon-fri|*|* -; -; ignorepat can be used to instruct drivers to not cancel dialtone upon -; receipt of a particular pattern. The most commonly used example is -; of course '9' like this: -; -;ignorepat => 9 -; -; so that dialtone remains even after dialing a 9. -; - -; -; Sample entries for extensions.conf -; -; -[dundi-e164-canonical] -; -; List canonical entries here -; -;exten => 12564286000,1,Macro(stdexten,6000,IAX2/foo) -;exten => _125642860XX,1,Dial(IAX2/otherbox/${EXTEN:7}) - -[dundi-e164-customers] -; -; If you are an ITSP or Reseller, list your customers here. -; -;exten => _12564286000,1,Dial(SIP/customer1) -;exten => _12564286001,1,Dial(IAX2/customer2) - -[dundi-e164-via-pstn] -; -; If you are freely delivering calls to the PSTN, list them here -; -;exten => _1256428XXXX,1,Dial(Zap/G2/${EXTEN:7}) ; Expose all of 256-428 -;exten => _1256325XXXX,1,Dial(Zap/G2/${EXTEN:7}) ; Ditto for 256-325 - -[dundi-e164-local] -; -; Context to put your dundi IAX2 or SIP user in for -; full access -; -include => dundi-e164-canonical -include => dundi-e164-customers -include => dundi-e164-via-pstn - -[dundi-e164-switch] -; -; Just a wrapper for the switch -; -switch => DUNDi/e164 - -[dundi-e164-lookup] -; -; Locally to lookup, try looking for a local E.164 solution -; then try DUNDi if we don't have one. -; -include => dundi-e164-local -include => dundi-e164-switch -; -; DUNDi can also be implemented as a Macro instead of using -; the Local channel driver. -; -[macro-dundi-e164] -; -; ARG1 is the extension to Dial -; -; Extension "s" is not a wildcard extension that matches "anything". -; In macros, it is the start extension. In most other cases, -; you have to goto "s" to execute that extension. -; -; For wildcard matches, see above - all pattern matches start with -; an underscore. -exten => s,1,Goto(${ARG1},1) -include => dundi-e164-lookup - -; -; Here are the entries you need to participate in the IAXTEL -; call routing system. Most IAXTEL numbers begin with 1-700, but -; there are exceptions. For more information, and to sign -; up, please go to www.gnophone.com or www.iaxtel.com -; -[iaxtel700] -exten => _91700XXXXXXX,1,Dial(IAX2/${GLOBAL(IAXINFO)}@iaxtel.com/${EXTEN:1}@iaxtel) - -; -; The SWITCH statement permits a server to share the dialplan with -; another server. Use with care: Reciprocal switch statements are not -; allowed (e.g. both A -> B and B -> A), and the switched server needs -; to be on-line or else dialing can be severly delayed. -; -[iaxprovider] -;switch => IAX2/user:[key]@myserver/mycontext - -[trunkint] -; -; International long distance through trunk -; -exten => _9011.,1,Macro(dundi-e164,${EXTEN:4}) -exten => _9011.,n,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}}) - -[trunkld] -; -; Long distance context accessed through trunk -; -exten => _91NXXNXXXXXX,1,Macro(dundi-e164,${EXTEN:1}) -exten => _91NXXNXXXXXX,n,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}}) - -[trunklocal] -; -; Local seven-digit dialing accessed through trunk interface -; -exten => _9NXXXXXX,1,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}}) - -[trunktollfree] -; -; Long distance context accessed through trunk interface -; -exten => _91800NXXXXXX,1,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}}) -exten => _91888NXXXXXX,1,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}}) -exten => _91877NXXXXXX,1,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}}) -exten => _91866NXXXXXX,1,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}}) - -[international] -; -; Master context for international long distance -; -ignorepat => 9 -include => longdistance -include => trunkint - -[longdistance] -; -; Master context for long distance -; -ignorepat => 9 -include => local -include => trunkld - -[local] -; -; Master context for local, toll-free, and iaxtel calls only -; -ignorepat => 9 -include => default -include => trunklocal -include => iaxtel700 -include => trunktollfree -include => iaxprovider - -;Include parkedcalls (or the context you define in features conf) -;to enable call parking. -include => parkedcalls -; -; You can use an alternative switch type as well, to resolve -; extensions that are not known here, for example with remote -; IAX switching you transparently get access to the remote -; Asterisk PBX -; -; switch => IAX2/user:password@bigserver/local -; -; An "lswitch" is like a switch but is literal, in that -; variable substitution is not performed at load time -; but is passed to the switch directly (presumably to -; be substituted in the switch routine itself) -; -; lswitch => Loopback/12${EXTEN}@othercontext -; -; An "eswitch" is like a switch but the evaluation of -; variable substitution is performed at runtime before -; being passed to the switch routine. -; -; eswitch => IAX2/context@${CURSERVER} - -[macro-trunkdial] -; -; Standard trunk dial macro (hangs up on a dialstatus that should -; terminate call) -; ${ARG1} - What to dial -; -exten => s,1,Dial(${ARG1}) -exten => s,n,Goto(s-${DIALSTATUS},1) -exten => s-NOANSWER,1,Hangup -exten => s-BUSY,1,Hangup -exten => _s-.,1,NoOp - -[macro-stdexten]; -; -; Standard extension macro: -; ${ARG1} - Extension (we could have used ${MACRO_EXTEN} here as well -; ${ARG2} - Device(s) to ring -; -exten => s,1,Dial(${ARG2},20) ; Ring the interface, 20 seconds maximum -exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status (NOANSWER,BUSY,CHANUNAVAIL,CONGESTION,ANSWER) - -exten => s-NOANSWER,1,Voicemail(${ARG1},u) ; If unavailable, send to voicemail w/ unavail announce -exten => s-NOANSWER,2,Goto(default,s,1) ; If they press #, return to start - -exten => s-BUSY,1,Voicemail(${ARG1},b) ; If busy, send to voicemail w/ busy announce -exten => s-BUSY,2,Goto(default,s,1) ; If they press #, return to start - -exten => _s-.,1,Goto(s-NOANSWER,1) ; Treat anything else as no answer - -exten => a,1,VoicemailMain(${ARG1}) ; If they press *, send the user into VoicemailMain - -[macro-stdPrivacyexten]; -; -; Standard extension macro: -; ${ARG1} - Extension (we could have used ${MACRO_EXTEN} here as well -; ${ARG2} - Device(s) to ring -; ${ARG3} - Optional DONTCALL context name to jump to (assumes the s,1 extension-priority) -; ${ARG4} - Optional TORTURE context name to jump to (assumes the s,1 extension-priority)` -; -exten => s,1,Dial(${ARG2},20|p) ; Ring the interface, 20 seconds maximum, call screening - ; option (or use P for databased call screening) -exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status (NOANSWER,BUSY,CHANUNAVAIL,CONGESTION,ANSWER) - -exten => s-NOANSWER,1,Voicemail(${ARG1},u) ; If unavailable, send to voicemail w/ unavail announce -exten => s-NOANSWER,2,Goto(default,s,1) ; If they press #, return to start - -exten => s-BUSY,1,Voicemail(${ARG1},b) ; If busy, send to voicemail w/ busy announce -exten => s-BUSY,2,Goto(default,s,1) ; If they press #, return to start - -exten => s-DONTCALL,1,Goto(${ARG3},s,1) ; Callee chose to send this call to a polite "Don't call again" script. - -exten => s-TORTURE,1,Goto(${ARG4},s,1) ; Callee chose to send this call to a telemarketer torture script. - -exten => _s-.,1,Goto(s-NOANSWER,1) ; Treat anything else as no answer - -exten => a,1,VoicemailMain(${ARG1}) ; If they press *, send the user into VoicemailMain - -[macro-page]; -; -; Paging macro: -; -; Check to see if SIP device is in use and DO NOT PAGE if they are -; -; ${ARG1} - Device to page - -exten => s,1,ChanIsAvail(${ARG1}|js) ; j is for Jump and s is for ANY call -exten => s,n,GoToIf([${AVAILSTATUS} = "1"]?autoanswer:fail) -exten => s,n(autoanswer),Set(_ALERT_INFO="RA") ; This is for the PolyComs -exten => s,n,SIPAddHeader(Call-Info: Answer-After=0) ; This is for the Grandstream, Snoms, and Others -exten => s,n,NoOp() ; Add others here and Post on the Wiki!!!! -exten => s,n,Dial(${ARG1}||) -exten => s,n(fail),Hangup - - -[demo] -; -; We start with what to do when a call first comes in. -; -exten => s,1,Wait(1) ; Wait a second, just for fun -exten => s,n,Answer ; Answer the line -exten => s,n,Set(TIMEOUT(digit)=5) ; Set Digit Timeout to 5 seconds -exten => s,n,Set(TIMEOUT(response)=10) ; Set Response Timeout to 10 seconds -exten => s,n(restart),BackGround(demo-congrats) ; Play a congratulatory message -exten => s,n(instruct),BackGround(demo-instruct) ; Play some instructions -exten => s,n,WaitExten ; Wait for an extension to be dialed. - -exten => 2,1,BackGround(demo-moreinfo) ; Give some more information. -exten => 2,n,Goto(s,instruct) - -exten => 3,1,Set(LANGUAGE()=fr) ; Set language to french -exten => 3,n,Goto(s,restart) ; Start with the congratulations - -exten => 1000,1,Goto(default,s,1) -; -; We also create an example user, 1234, who is on the console and has -; voicemail, etc. -; -exten => 1234,1,Playback(transfer,skip) ; "Please hold while..." - ; (but skip if channel is not up) -exten => 1234,n,Macro(stdexten,1234,${GLOBAL(CONSOLE)}) - -exten => 1235,1,Voicemail(1234,u) ; Right to voicemail - -exten => 1236,1,Dial(Console/dsp) ; Ring forever -exten => 1236,n,Voicemail(1234,b) ; Unless busy - -; -; # for when they're done with the demo -; -exten => #,1,Playback(demo-thanks) ; "Thanks for trying the demo" -exten => #,n,Hangup ; Hang them up. - -; -; A timeout and "invalid extension rule" -; -exten => t,1,Goto(#,1) ; If they take too long, give up -exten => i,1,Playback(invalid) ; "That's not valid, try again" - -; -; Create an extension, 500, for dialing the -; Asterisk demo. -; -exten => 500,1,Playback(demo-abouttotry); Let them know what's going on -exten => 500,n,Dial(IAX2/guest@pbx.digium.com/s@default) ; Call the Asterisk demo -exten => 500,n,Playback(demo-nogo) ; Couldn't connect to the demo site -exten => 500,n,Goto(s,6) ; Return to the start over message. - -; -; Create an extension, 600, for evaluating echo latency. -; -exten => 600,1,Playback(demo-echotest) ; Let them know what's going on -exten => 600,n,Echo ; Do the echo test -exten => 600,n,Playback(demo-echodone) ; Let them know it's over -exten => 600,n,Goto(s,6) ; Start over - -; -; You can use the Macro Page to intercom a individual user -exten => 76245,1,Macro(page,SIP/Grandstream1) -; or if your peernames are the same as extensions -exten => _7XXX,1,Macro(page,SIP/${EXTEN}) -; -; -; System Wide Page at extension 7999 -; -exten => 7999,1,Set(TIMEOUT(absolute)=60) -exten => 7999,2,Page(Local/Grandstream1@page&Local/Xlite1@page&Local/1234@page/n|d) - -; Give voicemail at extension 8500 -; -exten => 8500,1,VoicemailMain -exten => 8500,n,Goto(s,6) -; -; Here's what a phone entry would look like (IXJ for example) -; -;exten => 1265,1,Dial(Phone/phone0,15) -;exten => 1265,n,Goto(s,5) - -; -; The page context calls up the page macro that sets variables needed for auto-answer -; It is in is own context to make calling it from the Page() application as simple as -; Local/{peername}@page -; -[page] -exten => _X.,1,Macro(page,SIP/${EXTEN}) - -;[mainmenu] -; -; Example "main menu" context with submenu -; -;exten => s,1,Answer -;exten => s,n,Background(thanks) ; "Thanks for calling press 1 for sales, 2 for support, ..." -;exten => s,n,WaitExten -;exten => 1,1,Goto(submenu,s,1) -;exten => 2,1,Hangup -;include => default -; -;[submenu] -;exten => s,1,Ringing ; Make them comfortable with 2 seconds of ringback -;exten => s,n,Wait,2 -;exten => s,n,Background(submenuopts) ; "Thanks for calling the sales department. Press 1 for steve, 2 for..." -;exten => s,n,WaitExten -;exten => 1,1,Goto(default,steve,1) -;exten => 2,1,Goto(default,mark,2) - -[default] -; -; By default we include the demo. In a production system, you -; probably don't want to have the demo there. -; -include => demo - -; -; An extension like the one below can be used for FWD, Nikotel, sipgate etc. -; Note that you must have a [sipprovider] section in sip.conf -; -;exten => _41X.,1,Dial(SIP/${EXTEN:2}@sipprovider,,r) - -; Real extensions would go here. Generally you want real extensions to be -; 4 or 5 digits long (although there is no such requirement) and start with a -; single digit that is fairly large (like 6 or 7) so that you have plenty of -; room to overlap extensions and menu options without conflict. You can alias -; them with names, too, and use global variables - -;exten => 6245,hint,SIP/Grandstream1&SIP/Xlite1,Joe Schmoe ; Channel hints for presence -;exten => 6245,1,Dial(SIP/Grandstream1,20,rt) ; permit transfer -;exten => 6245,n(dial),Dial(${HINT},20,rtT) ; Use hint as listed -;exten => 6245,n,Voicemail(6245,u) ; Voicemail (unavailable) -;exten => 6245,s+1,Hangup ; s+1, same as n -;exten => 6245,dial+101,Voicemail(6245,b) ; Voicemail (busy) -;exten => 6361,1,Dial(IAX2/JaneDoe,,rm) ; ring without time limit -;exten => 6389,1,Dial(MGCP/aaln/1@192.168.0.14) -;exten => 6390,1,Dial(JINGLE/caller/callee) ; Dial via jingle using labels -;exten => 6391,1,Dial(JINGLE/asterisk@digium.com/mogorman@astjab.org) ;Dial via jingle using asterisk as the transport and calling mogorman. -;exten => 6394,1,Dial(Local/6275/n) ; this will dial ${MARK} - -;exten => 6275,1,Macro(stdexten,6275,${MARK}) ; assuming ${MARK} is something like Zap/2 -;exten => mark,1,Goto(6275|1) ; alias mark to 6275 -;exten => 6536,1,Macro(stdexten,6236,${WIL}) ; Ditto for wil -;exten => wil,1,Goto(6236|1) - -;If you want to subscribe to the status of a parking space, this is -;how you do it. Subscribe to extension 6600 in sip, and you will see -;the status of the first parking lot with this extensions' help -;exten => 6600,hint,park:701@parkedcalls -;exten => 6600,1,noop -; -; Some other handy things are an extension for checking voicemail via -; voicemailmain -; -;exten => 8500,1,VoicemailMain -;exten => 8500,n,Hangup -; -; Or a conference room (you'll need to edit meetme.conf to enable this room) -; -;exten => 8600,1,Meetme(1234) -; -; Or playing an announcement to the called party, as soon it answers -; -;exten = 8700,1,Dial(${MARK},30,A(/path/to/my/announcemsg)) -; -; For more information on applications, just type "core show applications" at your -; friendly Asterisk CLI prompt. -; -; "core show application <command>" will show details of how you -; use that particular application in this file, the dial plan. -; "core show functions" will list all dialplan functions -; "core show function <COMMAND>" will show you more information about -; one function. Remember that function names are UPPER CASE. |