diff options
Diffstat (limited to '1.4.23-rc4/configs/chan_dahdi.conf.sample')
| -rw-r--r-- | 1.4.23-rc4/configs/chan_dahdi.conf.sample | 675 |
1 files changed, 0 insertions, 675 deletions
diff --git a/1.4.23-rc4/configs/chan_dahdi.conf.sample b/1.4.23-rc4/configs/chan_dahdi.conf.sample deleted file mode 100644 index 2dbbb41d0..000000000 --- a/1.4.23-rc4/configs/chan_dahdi.conf.sample +++ /dev/null @@ -1,675 +0,0 @@ -; -; DAHDI telephony interface -; -; Configuration file -; -; You need to restart Asterisk to re-configure the DAHDI channels -; CLI> reload chan_dahdi.so -; will reload the configuration file, -; but not all configuration options are -; re-configured during a reload. - - - -[trunkgroups] -; -; Trunk groups are used for NFAS or GR-303 connections. -; -; Group: Defines a trunk group. -; trunkgroup => <trunkgroup>,<dchannel>[,<backup1>...] -; -; trunkgroup is the numerical trunk group to create -; dchannel is the DAHDI channel which will have the -; d-channel for the trunk. -; backup1 is an optional list of backup d-channels. -; -;trunkgroup => 1,24,48 -;trunkgroup => 1,24 -; -; Spanmap: Associates a span with a trunk group -; spanmap => <dahdispan>,<trunkgroup>[,<logicalspan>] -; -; dahdispan is the DAHDI span number to associate -; trunkgroup is the trunkgroup (specified above) for the mapping -; logicalspan is the logical span number within the trunk group to use. -; if unspecified, no logical span number is used. -; -;spanmap => 1,1,1 -;spanmap => 2,1,2 -;spanmap => 3,1,3 -;spanmap => 4,1,4 - -[channels] -; -; Default language -; -;language=en -; -; Default context -; -context=default -; -; Switchtype: Only used for PRI. -; -; national: National ISDN 2 (default) -; dms100: Nortel DMS100 -; 4ess: AT&T 4ESS -; 5ess: Lucent 5ESS -; euroisdn: EuroISDN (also known as ETSI NET/5; Cisco calls this "primary-net5") -; ni1: Old National ISDN 1 -; qsig: Q.SIG -; -switchtype=national -; -; Some switches (AT&T especially) require network specific facility IE -; supported values are currently 'none', 'sdn', 'megacom', 'tollfreemegacom', 'accunet' -; -;nsf=none -; -; PRI Dialplan: Only RARELY used for PRI. -; -; unknown: Unknown -; private: Private ISDN -; local: Local ISDN -; national: National ISDN -; international: International ISDN -; dynamic: Dynamically selects the appropriate dialplan -; -;pridialplan=national -; -; PRI Local Dialplan: Only RARELY used for PRI (sets the calling number's numbering plan) -; -; unknown: Unknown -; private: Private ISDN -; local: Local ISDN -; national: National ISDN -; international: International ISDN -; dynamic: Dynamically selects the appropriate dialplan -; -;prilocaldialplan=national -; -; PRI callerid prefixes based on the given TON/NPI (dialplan) -; This is especially needed for euroisdn E1-PRIs -; -; sample 1 for Germany -;internationalprefix = 00 -;nationalprefix = 0 -;localprefix = 0711 -;privateprefix = 07115678 -;unknownprefix = -; -; sample 2 for Germany -;internationalprefix = + -;nationalprefix = +49 -;localprefix = +49711 -;privateprefix = +497115678 -;unknownprefix = -; -; PRI resetinterval: sets the time in seconds between restart of unused -; channels, defaults to 3600; minimum 60 seconds. Some PBXs don't like -; channel restarts. so set the interval to a very long interval e.g. 100000000 -; or 'never' to disable *entirely*. -; -;resetinterval = 3600 -; -; Overlap dialing mode (sending overlap digits) -; -;overlapdial=yes -; -; Allow inband audio (progress) when a call is RELEASEd by the far end of a PRI -; -;inbanddisconnect=yes -; -; PRI Out of band indications. -; Enable this to report Busy and Congestion on a PRI using out-of-band -; notification. Inband indication, as used by Asterisk doesn't seem to work -; with all telcos. -; -; outofband: Signal Busy/Congestion out of band with RELEASE/DISCONNECT -; inband: Signal Busy/Congestion using in-band tones -; -; priindication = outofband -; -; If you need to override the existing channels selection routine and force all -; PRI channels to be marked as exclusively selected, set this to yes. -; priexclusive = yes -; -; ISDN Timers -; All of the ISDN timers and counters that are used are configurable. Specify -; the timer name, and its value (in ms for timers). -; K: Layer 2 max number of outstanding unacknowledged I frames (default 7) -; N200: Layer 2 max number of retransmissions of a frame (default 3) -; T200: Layer 2 max time before retransmission of a frame (default 1000 ms) -; T203: Layer 2 max time without frames being exchanged (default 10000 ms) -; T305: Wait for DISCONNECT acknowledge (default 30000 ms) -; T308: Wait for RELEASE acknowledge (default 4000 ms) -; T309: Maintain active calls on Layer 2 disconnection (default -1, Asterisk clears calls) -; EuroISDN: 6000 to 12000 ms, according to (N200 + 1) x T200 + 2s -; May vary in other ISDN standards (Q.931 1993 : 90000 ms) -; T313: Wait for CONNECT acknowledge, CPE side only (default 3000 ms) -; -; pritimer => t200,1000 -; pritimer => t313,4000 -; -; To enable transmission of facility-based ISDN supplementary services (such -; as caller name from CPE over facility), enable this option. -; facilityenable = yes -; -; -; Signalling method (default is fxs). Valid values: -; em: E & M -; em_w: E & M Wink -; featd: Feature Group D (The fake, Adtran style, DTMF) -; featdmf: Feature Group D (The real thing, MF (domestic, US)) -; featdmf_ta: Feature Group D (The real thing, MF (domestic, US)) through -; a Tandem Access point -; featb: Feature Group B (MF (domestic, US)) -; fgccama Feature Group C-CAMA (DP DNIS, MF ANI) -; fgccamamf Feature Group C-CAMA MF (MF DNIS, MF ANI) -; fxs_ls: FXS (Loop Start) -; fxs_gs: FXS (Ground Start) -; fxs_ks: FXS (Kewl Start) -; fxo_ls: FXO (Loop Start) -; fxo_gs: FXO (Ground Start) -; fxo_ks: FXO (Kewl Start) -; pri_cpe: PRI signalling, CPE side -; pri_net: PRI signalling, Network side -; gr303fxoks_net: GR-303 Signalling, FXO Loopstart, Network side -; gr303fxsks_cpe: GR-303 Signalling, FXS Loopstart, CPE side -; sf: SF (Inband Tone) Signalling -; sf_w: SF Wink -; sf_featd: SF Feature Group D (The fake, Adtran style, DTMF) -; sf_featdmf: SF Feature Group D (The real thing, MF (domestic, US)) -; sf_featb: SF Feature Group B (MF (domestic, US)) -; e911: E911 (MF) style signalling -; -; The following are used for Radio interfaces: -; fxs_rx: Receive audio/COR on an FXS kewlstart interface (FXO at the -; channel bank) -; fxs_tx: Transmit audio/PTT on an FXS loopstart interface (FXO at the -; channel bank) -; fxo_rx: Receive audio/COR on an FXO loopstart interface (FXS at the -; channel bank) -; fxo_tx: Transmit audio/PTT on an FXO groundstart interface (FXS at -; the channel bank) -; em_rx: Receive audio/COR on an E&M interface (1-way) -; em_tx: Transmit audio/PTT on an E&M interface (1-way) -; em_txrx: Receive audio/COR AND Transmit audio/PTT on an E&M interface -; (2-way) -; em_rxtx: Same as em_txrx (for our dyslexic friends) -; sf_rx: Receive audio/COR on an SF interface (1-way) -; sf_tx: Transmit audio/PTT on an SF interface (1-way) -; sf_txrx: Receive audio/COR AND Transmit audio/PTT on an SF interface -; (2-way) -; sf_rxtx: Same as sf_txrx (for our dyslexic friends) -; -signalling=fxo_ls -; -; If you have an outbound signalling format that is different from format -; specified above (but compatible), you can specify outbound signalling format, -; (see below). The 'signalling' format specified will be the inbound signalling -; format. If you only specify 'signalling', then it will be the format for -; both inbound and outbound. -; -; signalling=featdmf -; outsignalling=featb -; -; For Feature Group D Tandem access, to set the default CIC and OZZ use these -; parameters: -;defaultozz=0000 -;defaultcic=303 -; -; A variety of timing parameters can be specified as well -; Including: -; prewink: Pre-wink time (default 50ms) -; preflash: Pre-flash time (default 50ms) -; wink: Wink time (default 150ms) -; flash: Flash time (default 750ms) -; start: Start time (default 1500ms) -; rxwink: Receiver wink time (default 300ms) -; rxflash: Receiver flashtime (default 1250ms) -; debounce: Debounce timing (default 600ms) -; -rxwink=300 ; Atlas seems to use long (250ms) winks -; -; How long generated tones (DTMF and MF) will be played on the channel -; (in milliseconds) -;toneduration=100 -; -; Whether or not to do distinctive ring detection on FXO lines -; -;usedistinctiveringdetection=yes -;distinctiveringaftercid=yes ; enable dring detection after callerid for those countries like Australia - ; where the ring cadence is changed *after* the callerid spill. -; -; Whether or not to use caller ID -; -usecallerid=yes -; -; Type of caller ID signalling in use -; bell = bell202 as used in US -; v23 = v23 as used in the UK -; v23_jp = v23 as used in Japan -; dtmf = DTMF as used in Denmark, Sweden and Netherlands -; smdi = Use SMDI for callerid. Requires SMDI to be enabled (usesmdi). -; -;cidsignalling=bell -; -; What signals the start of caller ID -; ring = a ring signals the start -; polarity = polarity reversal signals the start -; -;cidstart=ring -; -; Whether or not to hide outgoing caller ID (Override with *67 or *82) -; -hidecallerid=no -; -; Whether or not to enable call waiting on internal extensions -; With this set to 'yes', busy extensions will hear the call-waiting -; tone, and can use hook-flash to switch between callers. The Dial() -; app will not return the "BUSY" result for extensions. -; -callwaiting=yes -; -; Whether or not restrict outgoing caller ID (will be sent as ANI only, not -; available for the user) -; Mostly use with FXS ports -; -;restrictcid=no -; -; Whether or not use the caller ID presentation for the outgoing call that the -; calling switch is sending. -; See doc/callingpres.txt -; -usecallingpres=yes -; -; Some countries (UK) have ring tones with different ring tones (ring-ring), -; which means the callerid needs to be set later on, and not just after -; the first ring, as per the default. -; -;sendcalleridafter=1 -; -; -; Support Caller*ID on Call Waiting -; -callwaitingcallerid=yes -; -; Support three-way calling -; -threewaycalling=yes -; -; For FXS ports (either direct analog or over T1/E1): -; Support flash-hook call transfer (requires three way calling) -; Also enables call parking (overrides the 'canpark' parameter) -; -; For digital ports using ISDN PRI protocols: -; Support switch-side transfer (called 2BCT, RLT or other names) -; This setting must be enabled on both ports involved, and the -; 'facilityenable' setting must also be enabled to allow sending -; the transfer to the ISDN switch, since it sent in a FACILITY -; message. -; -transfer=yes -; -; Allow call parking -; ('canpark=no' is overridden by 'transfer=yes') -; -canpark=yes -; -; Support call forward variable -; -cancallforward=yes -; -; Whether or not to support Call Return (*69) -; -callreturn=yes -; -; Stutter dialtone support: If a mailbox is specified without a voicemail -; context, then when voicemail is received in a mailbox in the default -; voicemail context in voicemail.conf, taking the phone off hook will cause a -; stutter dialtone instead of a normal one. -; -; If a mailbox is specified *with* a voicemail context, the same will result -; if voicemail received in mailbox in the specified voicemail context. -; -; for default voicemail context, the example below is fine: -; -;mailbox=1234 -; -; for any other voicemail context, the following will produce the stutter tone: -; -;mailbox=1234@context -; -; Enable echo cancellation -; Use either "yes", "no", or a power of two from 32 to 256 if you wish to -; actually set the number of taps of cancellation. -; -; Note that when setting the number of taps, the number 256 does not translate -; to 256 ms of echo cancellation. echocancel=256 means 256 / 8 = 32 ms. -; -; Note that if any of your DAHDI cards have hardware echo cancellers, -; then this setting only turns them on and off; numeric settings will -; be treated as "yes". There are no special settings required for -; hardware echo cancellers; when present and enabled in their kernel -; modules, they take precedence over the software echo canceller compiled -; into DAHDI automatically. -; -echocancel=yes -; -; Generally, it is not necessary (and in fact undesirable) to echo cancel when -; the circuit path is entirely TDM. You may, however, change this behavior -; by enabling the echo cancel during pure TDM bridging below. -; -echocancelwhenbridged=yes -; -; In some cases, the echo canceller doesn't train quickly enough and there -; is echo at the beginning of the call. Enabling echo training will cause -; asterisk to briefly mute the channel, send an impulse, and use the impulse -; response to pre-train the echo canceller so it can start out with a much -; closer idea of the actual echo. Value may be "yes", "no", or a number of -; milliseconds to delay before training (default = 400) -; -; WARNING: In some cases this option can make echo worse! If you are -; trying to debug an echo problem, it is worth checking to see if your echo -; is better with the option set to yes or no. Use whatever setting gives -; the best results. -; -; Note that these parameters do not apply to hardware echo cancellers. -; -;echotraining=yes -;echotraining=800 -; -; If you are having trouble with DTMF detection, you can relax the DTMF -; detection parameters. Relaxing them may make the DTMF detector more likely -; to have "talkoff" where DTMF is detected when it shouldn't be. -; -;relaxdtmf=yes -; -; You may also set the default receive and transmit gains (in dB) -; -rxgain=0.0 -txgain=0.0 -; -; Logical groups can be assigned to allow outgoing rollover. Groups range -; from 0 to 63, and multiple groups can be specified. -; -group=1 -; -; Ring groups (a.k.a. call groups) and pickup groups. If a phone is ringing -; and it is a member of a group which is one of your pickup groups, then -; you can answer it by picking up and dialling *8#. For simple offices, just -; make these both the same. Groups range from 0 to 63. -; -callgroup=1 -pickupgroup=1 - -; -; Specify whether the channel should be answered immediately or if the simple -; switch should provide dialtone, read digits, etc. -; Note: If immediate=yes the dialplan execution will always start at extension -; 's' priority 1 regardless of the dialed number! -; -immediate=no -; -; Specify whether flash-hook transfers to 'busy' channels should complete or -; return to the caller performing the transfer (default is yes). -; -;transfertobusy=no -; -; CallerID can be set to "asreceived" or a specific number if you want to -; override it. Note that "asreceived" only applies to trunk interfaces. -; -;callerid=2564286000 -; -; AMA flags affects the recording of Call Detail Records. If specified -; it may be 'default', 'omit', 'billing', or 'documentation'. -; -;amaflags=default -; -; Channels may be associated with an account code to ease -; billing -; -;accountcode=lss0101 -; -; ADSI (Analog Display Services Interface) can be enabled on a per-channel -; basis if you have (or may have) ADSI compatible CPE equipment -; -;adsi=yes -; -; SMDI (Simplified Message Desk Interface) can be enabled on a per-channel -; basis if you would like that channel to behave like an SMDI message desk. -; The SMDI port specified should have already been defined in smdi.conf. The -; default port is /dev/ttyS0. -; -;usesmdi=yes -;smdiport=/dev/ttyS0 -; -; On trunk interfaces (FXS) and E&M interfaces (E&M, Wink, Feature Group D -; etc, it can be useful to perform busy detection either in an effort to -; detect hangup or for detecting busies. This enables listening for -; the beep-beep busy pattern. -; -;busydetect=yes -; -; If busydetect is enabled, it is also possible to specify how many busy tones -; to wait for before hanging up. The default is 4, but better results can be -; achieved if set to 6 or even 8. Mind that the higher the number, the more -; time that will be needed to hangup a channel, but lowers the probability -; that you will get random hangups. -; -;busycount=4 -; -; If busydetect is enabled, it is also possible to specify the cadence of your -; busy signal. In many countries, it is 500msec on, 500msec off. Without -; busypattern specified, we'll accept any regular sound-silence pattern that -; repeats <busycount> times as a busy signal. If you specify busypattern, -; then we'll further check the length of the sound (tone) and silence, which -; will further reduce the chance of a false positive. -; -;busypattern=500,500 -; -; NOTE: In the Asterisk Makefile you'll find further options to tweak the busy -; detector. If your country has a busy tone with the same length tone and -; silence (as many countries do), consider defining the -; -DBUSYDETECT_COMPARE_TONE_AND_SILENCE option. -; -; Use a polarity reversal to mark when a outgoing call is answered by the -; remote party. -; -;answeronpolarityswitch=yes -; -; In some countries, a polarity reversal is used to signal the disconnect of a -; phone line. If the hanguponpolarityswitch option is selected, the call will -; be considered "hung up" on a polarity reversal. -; -;hanguponpolarityswitch=yes -; -; On trunk interfaces (FXS) it can be useful to attempt to follow the progress -; of a call through RINGING, BUSY, and ANSWERING. If turned on, call -; progress attempts to determine answer, busy, and ringing on phone lines. -; This feature is HIGHLY EXPERIMENTAL and can easily detect false answers, -; so don't count on it being very accurate. -; -; Few zones are supported at the time of this writing, but may be selected -; with "progzone" -; -; This feature can also easily detect false hangups. The symptoms of this is -; being disconnected in the middle of a call for no reason. -; -;callprogress=yes -;progzone=us -; -; FXO (FXS signalled) devices must have a timeout to determine if there was a -; hangup before the line was answered. This value can be tweaked to shorten -; how long it takes before DAHDI considers a non-ringing line to have hungup. -; -;ringtimeout=8000 -; -; For FXO (FXS signalled) devices, whether to use pulse dial instead of DTMF -; -;pulsedial=yes -; -; For fax detection, uncomment one of the following lines. The default is *OFF* -; -;faxdetect=both -;faxdetect=incoming -;faxdetect=outgoing -;faxdetect=no -; -; This option specifies a preference for which music on hold class this channel -; should listen to when put on hold if the music class has not been set on the -; channel with Set(CHANNEL(musicclass)=whatever) in the dialplan, and the peer -; channel putting this one on hold did not suggest a music class. -; -; If this option is set to "passthrough", then the hold message will always be -; passed through as signalling instead of generating hold music locally. This -; setting is only valid when used on a channel that uses digital signalling. -; -; This option may be specified globally, or on a per-channel basis. -; -;mohinterpret=default -; -; This option specifies which music on hold class to suggest to the peer channel -; when this channel places the peer on hold. It may be specified globally or on -; a per-channel. -; -;mohsuggest=default -; -; PRI channels can have an idle extension and a minunused number. So long as -; at least "minunused" channels are idle, chan_dahdi will try to call "idledial" -; on them, and then dump them into the PBX in the "idleext" extension (which -; is of the form exten@context). When channels are needed the "idle" calls -; are disconnected (so long as there are at least "minidle" calls still -; running, of course) to make more channels available. The primary use of -; this is to create a dynamic service, where idle channels are bundled through -; multilink PPP, thus more efficiently utilizing combined voice/data services -; than conventional fixed mappings/muxings. -; -;idledial=6999 -;idleext=6999@dialout -;minunused=2 -;minidle=1 -; -; Configure jitter buffers in DAHDI (each one is 20ms, default is 4) -; -;jitterbuffers=4 -; -;------------------------------ JITTER BUFFER CONFIGURATION -------------------------- -; jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of a - ; DAHDI channel. Defaults to "no". An enabled jitterbuffer will - ; be used only if the sending side can create and the receiving - ; side can not accept jitter. The DAHDI channel can't accept jitter, - ; thus an enabled jitterbuffer on the receive DAHDI side will always - ; be used if the sending side can create jitter. - -; jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds. - -; jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is - ; resynchronized. Useful to improve the quality of the voice, with - ; big jumps in/broken timestamps, usually sent from exotic devices - ; and programs. Defaults to 1000. - -; jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of a DAHDI - ; channel. Two implementations are currently available - "fixed" - ; (with size always equals to jbmax-size) and "adaptive" (with - ; variable size, actually the new jb of IAX2). Defaults to fixed. - -; jblog = no ; Enables jitterbuffer frame logging. Defaults to "no". -;----------------------------------------------------------------------------------- -; -; You can define your own custom ring cadences here. You can define up to 8 -; pairs. If the silence is negative, it indicates where the callerid spill is -; to be placed. Also, if you define any custom cadences, the default cadences -; will be turned off. -; -; Syntax is: cadence=ring,silence[,ring,silence[...]] -; -; These are the default cadences: -; -;cadence=125,125,2000,-4000 -;cadence=250,250,500,1000,250,250,500,-4000 -;cadence=125,125,125,125,125,-4000 -;cadence=1000,500,2500,-5000 -; -; Each channel consists of the channel number or range. It inherits the -; parameters that were specified above its declaration. -; -; For GR-303, CRV's are created like channels except they must start with the -; trunk group followed by a colon, e.g.: -; -; crv => 1:1 -; crv => 2:1-2,5-8 -; -; -;callerid="Green Phone"<(256) 428-6121> -;channel => 1 -;callerid="Black Phone"<(256) 428-6122> -;channel => 2 -;callerid="CallerID Phone" <(256) 428-6123> -;callerid="CallerID Phone" <(630) 372-1564> -;callerid="CallerID Phone" <(256) 704-4666> -;channel => 3 -;callerid="Pac Tel Phone" <(256) 428-6124> -;channel => 4 -;callerid="Uniden Dead" <(256) 428-6125> -;channel => 5 -;callerid="Cortelco 2500" <(256) 428-6126> -;channel => 6 -;callerid="Main TA 750" <(256) 428-6127> -;channel => 44 -; -; For example, maybe we have some other channels which start out in a -; different context and use E & M signalling instead. -; -;context=remote -;signaling=em -;channel => 15 -;channel => 16 - -;signalling=em_w -; -; All those in group 0 I'll use for outgoing calls -; -; Strip most significant digit (9) before sending -; -;stripmsd=1 -;callerid=asreceived -;group=0 -;signalling=fxs_ls -;channel => 45 - -;signalling=fxo_ls -;group=1 -;callerid="Joe Schmoe" <(256) 428-6131> -;channel => 25 -;callerid="Megan May" <(256) 428-6132> -;channel => 26 -;callerid="Suzy Queue" <(256) 428-6233> -;channel => 27 -;callerid="Larry Moe" <(256) 428-6234> -;channel => 28 -; -; Sample PRI (CPE) config: Specify the switchtype, the signalling as either -; pri_cpe or pri_net for CPE or Network termination, and generally you will -; want to create a single "group" for all channels of the PRI. -; -; switchtype = national -; signalling = pri_cpe -; group = 2 -; channel => 1-23 - -; - -; Used for distinctive ring support for x100p. -; You can see the dringX patterns is to set any one of the dringXcontext fields -; and they will be printed on the console when an inbound call comes in. -; -;dring1=95,0,0 -;dring1context=internal1 -;dring2=325,95,0 -;dring2context=internal2 -; If no pattern is matched here is where we go. -;context=default -;channel => 1 - |