diff options
Diffstat (limited to '1.2-netsec/configs/misdn.conf.sample')
| -rw-r--r-- | 1.2-netsec/configs/misdn.conf.sample | 267 |
1 files changed, 0 insertions, 267 deletions
diff --git a/1.2-netsec/configs/misdn.conf.sample b/1.2-netsec/configs/misdn.conf.sample deleted file mode 100644 index 8957e2fa6..000000000 --- a/1.2-netsec/configs/misdn.conf.sample +++ /dev/null @@ -1,267 +0,0 @@ -; -; chan_misdn sample config -; - -; general section: -; -; for debugging and general setup, things that are not bound to port groups -; - -[general] - -; set debugging flag: -; 0 - No Debug -; 1 - mISDN Messages and * - Messages, and * - State changes -; 2 - Messages + Message specific Informations (e.g. bearer capability) -; 3 - very Verbose, the above + lots of Driver specific infos -; 4 - even more Verbose than 3 -; -; default value: 0 -; -debug=0 - -; the big trace -; -; default value: [not set] -; -;tracefile=/var/log/misdn.trace - -; single call trace files -; set to true if you want to have them -; they depend on debug level -; -; default values: trace_calls : false -; trace_dir : /var/log/ -; -trace_calls=false -trace_dir=/var/log/ - -; set to yes if you want mISDN_dsp to bridge the calls in HW -; -; default value: yes -; -bridging=yes - -; stops dialtone after getting first digit on nt Port -; -; default value: yes -; -stop_tone_after_first_digit=yes - -; wether to append overlapdialed Digits to Extension or not -; -; default value: yes -; -append_digits2exten=yes - -; set this to yes if you have jollys mISDN which sends correct L1 Infos -; -; default value: yes -; -l1_info_ok=yes - -; set this to yes if you want to clear the l3 in case the l2 deactivates -; some environments have a flickering l2 which causes this option to -; damage active calls .. highly experimental -; -; default value: no -; -clear_l3=no - -; set the method to use for channel selection: -; standard - always choose the first free channel with the lowest number -; round_robin - use the round robin algorithm to select a channel. use this -; if you want to balance your load. -; -; default value: standard -; -method=standard - -;;; CRYPTION STUFF - -; Wether to look for dynamic crypting attempt -; -; default value: no -; -dynamic_crypt=no - -; crypt_prefix, what is used for crypting Protocol -; -; default value: [not set] -; -crypt_prefix=** - -; Keys for cryption, you reference them in the dialplan -; later also in dynamic encr. -; -; default value: [not set] -; -crypt_keys=test,muh - -; users sections: -; -; name your sections as you which but not "general" ! -; the secions are Groups, you can dial out in extensions.conf -; with Dial(mISDN/g:extern/101) where extern is a section name, -; chan_misdn tries every port in this section to find a -; new free channel -; - -; The default section is not a group section, it just contains config elements -; which are inherited by group sections. -; - -[default] - -; define your default context here -; -; default value: default -; -context=misdn - -; language -; -; default value: en -; -language=en - -; Prefixes for national and international, those are put before the -; oad if an according dialplan is set by the other end. -; -; default values: nationalprefix : 0 -; internationalprefix : 00 -; -nationalprefix=0 -internationalprefix=00 - -; set rx/tx gains between -8 and 8 to change the RX/TX Gain -; -; default values: rxgain: 0 -; txgain: 0 -; -rxgain=0 -txgain=0 - -; some telcos espacially in NL seem to need this set to yes, also in -; switzerland this seems to be important -; -; default value: no -; -te_choose_channel=no - -; dialplan options: -; -; 0 - unknown -; 1 - National -; 2 - International -; 4 - Subscriber -; -; This setting is used for outgoing calls -; -; default value: 0 -; -dialplan=0 - -; This is only for asterisk head and will result in only considering -; misdn.confs and misdn_set_opts callingpresentation informations if set to no. -; Otherwise asterisks callingpresentation overwrites misdn.confs settings. -; -; default value: yes -; -use_callingpres=yes - -; uncomment the following to get into s extension at extension conf -; there you can use DigitTimeout if you can't or don't want to use -; isdn overlap dial. -; note: This will jump into the s exten for every exten! -; -; default value: no -; -;always_immediate=no - -; uncomment the following if you want callers which called exactly the -; base number (so no extension is set) jump to the s extension. -; if the user dials something more it jumps to the correct extension -; instead -; -; default value: no -; -;immediate=no - -; uncomment the following to have hold and retrieve support -; -; default value: no -; -;hold_allowed=yes - -; Pickup and Callgroup -; -; deafult values: not set = 0 -; -;callgroup=1 -;pickupgroup=1 - -; Allows/Screens Callerid -; -; possible values: allowed,not_screened -; -; be aware, if you set to allowed you need to set a correct -; callerid in the dialplan or set it here in the misdn.conf -; Some Telcos don't care about wrong callerids, others do ! -; -; default value: allowed -; -;presentation=not_screened - -; this enables echocancellation, with the given number of taps -; be aware, move this setting only to outgoing portgroups! -; A value of zero turns echocancellation off. -; -; possible values are: 0,32,64,128,256,yes(=128),no(=0) -; -; default value: no -; -;echocancel=no - -; this disables echocancellation when the call is bridged between -; mISDN channels -; -; default value: no -; -echocancelwhenbridged=no - -; Set this to no to disable echotraining -; -; default value: yes -; -echotraining=yes - -[intern] -; define your ports, e.g. 1,2 (depends on mISDN-driver loading order) -ports=1,2 -; context where to go to when incoming Call on one of the above ports -context=Intern - -[internPP] -; if you want to have pp Protocol on one nt Port, you need -; to add a ptp directly after the portnumber, you can still add -; more ports and multiple ptp adds in your config. -ports=3ptp - -[first_extern] -; again port defs -ports=4 -; again a context for incomming calls -context=Extern1 -; msns for te ports, listen on those numbers on the above ports, and -; indicate the incoming calls to asterisk -; here you can give a comma seperated list or simply an '*' for -; any msn. -msns=* - -; here an example with given msns -[second_extern] -ports=5 -context=Extern2 -callerid=15 -msns=102,144,101,104 |