diff options
Diffstat (limited to '1.2-netsec/channels/h323/h323.conf.sample')
-rw-r--r-- | 1.2-netsec/channels/h323/h323.conf.sample | 123 |
1 files changed, 0 insertions, 123 deletions
diff --git a/1.2-netsec/channels/h323/h323.conf.sample b/1.2-netsec/channels/h323/h323.conf.sample deleted file mode 100644 index 42858ed74..000000000 --- a/1.2-netsec/channels/h323/h323.conf.sample +++ /dev/null @@ -1,123 +0,0 @@ -; The NuFone Network's -; Open H.323 driver configuration -; -[general] -port = 1720 -bindaddr = 1.2.3.4 ; this SHALL contain a single, valid IP address for this machine -;tos=lowdelay -; -; You may specify a global default AMA flag for iaxtel calls. It must be -; one of 'default', 'omit', 'billing', or 'documentation'. These flags -; are used in the generation of call detail records. -; -;amaflags = default -; -; You may specify a default account for Call Detail Records in addition -; to specifying on a per-user basis -; -;accountcode=lss0101 -; -; You can fine tune codecs here using "allow" and "disallow" clauses -; with specific codecs. Use "all" to represent all formats. -; -disallow=all -;allow=all ; turns on all installed codecs -;disallow=g723.1 ; Hm... Proprietary, don't use it... -allow=gsm ; Always allow GSM, it's cool :) -; -; User-Input Mode (DTMF) -; -; valid entries are: rfc2833, inband -; default is rfc2833 -;dtmfmode=rfc2833 -; -; Default RTP Payload to send RFC2833 DTMF on. This is used to -; interoperate with broken gateways which cannot successfully -; negotiate a RFC2833 payload type in the TerminalCapabilitySet. -; -; You may also specify on either a per-peer or per-user basis below. -;dtmfcodec=101 -; -; Set the gatekeeper -; DISCOVER - Find the Gk address using multicast -; DISABLE - Disable the use of a GK -; <IP address> or <Host name> - The acutal IP address or hostname of your GK -;gatekeeper = DISABLE -; -; -; Tell Asterisk whether or not to accept Gatekeeper -; routed calls or not. Normally this should always -; be set to yes, unless you want to have finer control -; over which users are allowed access to Asterisk. -; Default: YES -; -;AllowGKRouted = yes -; -; Optionally you can determine a user by Source IP versus its H.323 alias. -; Default behavour is to determine user by H.323 alias. -;UserByAlias=no -; -; Default context gets used in siutations where you are using -; the GK routed model or no type=user was found. This gives you -; the ability to either play an invalid message or to simply not -; use user authentication at all. -; -;context=default -; -; H.323 Alias definitions -; -; Type 'h323' will register aliases to the endpoint -; and Gatekeeper, if there is one. -; -; Example: if someone calls time@your.asterisk.box.com -; Asterisk will send the call to the extension 'time' -; in the context default -; -; [default] -; exten => time,1,Answer -; exten => time,2,Playback,current-time -; -; Keyword's 'prefix' and 'e164' are only make sense when -; used with a gatekeeper. You can specify either a prefix -; or E.164 this endpoint is responsible for terminating. -; -; Example: The H.323 alias 'det-gw' will tell the gatekeeper -; to route any call with the prefix 1248 to this alias. Keyword -; e164 is used when you want to specifiy a full telephone -; number. So a call to the number 18102341212 would be -; routed to the H.323 alias 'time'. -; -;[time] -;type=h323 -;e164=18102341212 -;context=default -; -;[det-gw] -;type=h323 -;prefix=1248,1313 -;context=detroit -; -; -; Inbound H.323 calls from BillyBob would land in the incoming -; context with a maximum of 4 concurrent incoming calls -; -; -; Note: If keyword 'incominglimit' are omitted Asterisk will not -; enforce any maximum number of concurrent calls. -; -;[BillyBob] -;type=user -;host=192.168.1.1 -;context=incoming -;incominglimit=4 -; -; -; Outbound H.323 call to Larry using SlowStart -; -[Larry] -type=peer -host=192.168.2.1 -noFastStart=yes - - - |