1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
|
/**
* \file
*
* \brief MACSC Driver configuration
*
* Copyright (c) 2014-2015 Atmel Corporation. All rights reserved.
*
* \asf_license_start
*
* \page License
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* 3. The name of Atmel may not be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* 4. This software may only be redistributed and used in connection with an
* Atmel microcontroller product.
*
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
* \asf_license_stop
*
*/
/*
* Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
*/
#ifndef CONF_EXAMPLE_H
#define CONF_EXAMPLE_H
#include "ioport.h"
#define SYS_CLK_SRC MACSC_16MHz
#define RTC_CLK_SRC MACSC_32KHz
#define ENABLE_SLEEP 0
#define ENABLE_AUTO_TIMESTAMP 0
#define ENABLE_BACKOFF_SLOT_CNTR 1
#define COMPARE_MODE MACSC_ABSOLUTE_CMP
/* We request a tick of 1Hz */
#define CONFIG_MACSC_TIMEOUT_TICK_HZ 62500
/*
* These pins(output) can be probed to check the timing duration of the
* functionalities of the MACSC.
*/
enum macsc_cb_pins {
OVF_INT_CHK_PIN = IOPORT_CREATE_PIN(PORTB,0), /*!< overflow interrupt toggle */
CMP1_INT_CHK_PIN = IOPORT_CREATE_PIN(PORTB,1), /*!< cmp1 int toggle */
CMP2_INT_CHK_PIN = IOPORT_CREATE_PIN(PORTB,2), /*!< cmp2 int toggle */
CMP3_INT_CHK_PIN = IOPORT_CREATE_PIN(PORTB,3), /*!< cmp3 int toggle */
BACKOFF_INT_CHK_PIN = IOPORT_CREATE_PIN(PORTB,4), /*!< back-off int toggle */
};
/*
* For USARTA1 connect a two wire cable for PORTD2 to connect with RXD
* For USARTA1 connect a two wire cable for PORTD3 to connect with TXD
*/
#define USART_SERIAL_PORT &USARTA1
#define USART_SERIAL_BAUDRATE 9600
#define USART_SERIAL_CHAR_LENGTH USART_CHSIZE_8BIT_gc
#define USART_SERIAL_PARITY USART_PMODE_DISABLED_gc
#define USART_SERIAL_STOP_BIT false
#endif /* CONF_EXAMPLE_H */
|
