/**
* \file
*
* \brief XMEGA-AT86RF233 Zigbit board init.
*
* This file contains board initialization function.
*
* Copyright (c) 2014-2015 Atmel Corporation. All rights reserved.
*
* \asf_license_start
*
* \page License
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* 3. The name of Atmel may not be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* 4. This software may only be redistributed and used in connection with an
* Atmel microcontroller product.
*
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
* \asf_license_stop
*
*/
/*
* Support and FAQ: visit Atmel Support
*/
#include
#include
#include
void board_init(void)
{
#ifdef ZIGBIT_USB
ioport_configure_pin(LED0_GPIO, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
ioport_configure_pin(LED1_GPIO, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
#endif
#ifdef ZIGBIT_EXT
ioport_configure_pin(LED0_GPIO, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
ioport_configure_pin(LED1_GPIO, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
ioport_configure_pin(LED2_GPIO, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
ioport_configure_pin(GPIO_PUSH_BUTTON_0, IOPORT_DIR_INPUT
| IOPORT_LEVEL | IOPORT_PULL_UP);
#endif
#ifdef CONF_BOARD_ENABLE_USARTE0
ioport_configure_pin(IOPORT_CREATE_PIN(PORTE, 3), IOPORT_DIR_OUTPUT
| IOPORT_INIT_HIGH);
ioport_configure_pin(IOPORT_CREATE_PIN(PORTE, 2), IOPORT_DIR_INPUT);
#endif
#ifdef CONF_BOARD_ENABLE_USARTD0
ioport_configure_pin(IOPORT_CREATE_PIN(PORTD, 3), IOPORT_DIR_OUTPUT
| IOPORT_INIT_HIGH);
ioport_configure_pin(IOPORT_CREATE_PIN(PORTD, 2), IOPORT_DIR_INPUT);
#endif
#ifdef CONF_BOARD_AT86RFX
ioport_configure_pin(AT86RFX_SPI_SCK, IOPORT_DIR_OUTPUT
| IOPORT_INIT_HIGH);
ioport_configure_pin(AT86RFX_SPI_MOSI, IOPORT_DIR_OUTPUT
| IOPORT_INIT_HIGH);
ioport_configure_pin(AT86RFX_SPI_MISO, IOPORT_DIR_INPUT);
ioport_configure_pin(AT86RFX_SPI_CS, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
/* Initialize TRX_RST and SLP_TR as GPIO. */
ioport_configure_pin(AT86RFX_RST_PIN, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
ioport_configure_pin(AT86RFX_SLP_PIN, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
#endif
}