mergecap - Merges two or more capture files into one
S<[ B<-a> ]>
S<[ B<-F> E<lt>I<file format>E<gt> ]>
S<[ B<-h> ]>
S<[ B<-I> E<lt>I<IDB merge mode>E<gt> ]>
S<[ B<-s> E<lt>I<snaplen>E<gt> ]>
S<[ B<-v> ]>
S<[ B<-V> ]>
E<lt>I<infile>E<gt> [E<lt>I<infile>E<gt> I<...>]
B<Mergecap> is a program that combines multiple saved capture files into
a single output file specified by the B<-w> argument. B<Mergecap> knows
how to read B<pcap> capture files, including those of B<tcpdump>,
B<Wireshark>, and other tools that write captures in that format.
By default, B<Mergecap> writes the capture file in B<pcap> format, and writes
all of the packets from the input capture files to the output file.
B<Mergecap> is able to detect, read and write the same capture files that
are supported by B<Wireshark>.
The input files don't need a specific filename extension; the file
format and an optional gzip compression will be automatically detected.
Near the beginning of the DESCRIPTION section of wireshark(1) or
is a detailed description of the way B<Wireshark> handles this, which is
the same way B<Mergecap> handles this.
B<Mergecap> can write the file in several output formats.
The B<-F> flag can be used to specify the format in which to write the
capture file, B<mergecap -F> provides a list of the available output
Packets from the input files are merged in chronological order based on
each frame's timestamp, unless the B<-a> flag is specified. B<Mergecap>
assumes that frames within a single capture file are already stored in
chronological order. When the B<-a> flag is specified, packets are
copied directly from each input file to the output file, independent of
each frame's timestamp.
The output file frame encapsulation type is set to the type of the input
files if all input files have the same type. If not all of the input
files have the same frame encapsulation type, the output file type is
set to WTAP_ENCAP_PER_PACKET. Note that some capture file formats, most
notably B<pcap>, do not currently support WTAP_ENCAP_PER_PACKET.
This combination will cause the output file creation to fail.
Causes the frame timestamps to be ignored, writing all packets from the
first input file followed by all packets from the second input file. By
default, when B<-a> is not specified, the contents of the input files
are merged in chronological order based on each frame's timestamp.
Note: when merging, B<mergecap> assumes that packets within a capture
file are already in chronological order.
=item -F E<lt>file formatE<gt>
Sets the file format of the output capture file. B<Mergecap> can write
the file in several formats; B<mergecap -F> provides a list of the
available output formats. The default is to use the file format of the
first input file.
Prints the version and options and exits.
=item -I E<lt>IDB merge modeE<gt>
Sets the Interface Description Block (IDB) merge mode to use during merging.
B<mergecap -I> provides a list of the available IDB merge modes.
Every input file has one or more IDBs, which describe the interface(s) the
capture was performed on originally. This includes encapsulation type,
interface name, etc. When mergecap merges multiple input files, it has to
merge these IDBs somehow for the new merged output file. This flag controls
how that is accomplished. The currently available modes are:
* 'B<none>': no merging of IDBs is performed, and instead all IDBs are
copied to the merged output file.
* 'B<all>': IDBs are merged only if all input files have the same number
of IDBs, and each IDB matches their respective entry in the
other files. This is the default mode.
* 'B<any>': Any and all duplicate IDBs are merged into one IDB, regardless
of what file they are in.
Note that an IDB is only considered a matching duplicate if it has the same
encapsulation type, name, speed, time precision, comments, description, etc.
=item -s E<lt>snaplenE<gt>
Sets the snapshot length to use when writing the data.
If the B<-s> flag is used to specify a snapshot length, frames in the
input file with more captured data than the specified snapshot length
will have only the amount of data specified by the snapshot length
written to the output file. This may be useful if the program that is
to read the output file cannot handle packets larger than a certain size
(for example, the versions of snoop in Solaris 2.5.1 and Solaris 2.6
appear to reject Ethernet frames larger than the standard Ethernet MTU,
making them incapable of handling gigabit Ethernet captures if jumbo
frames were used).
Causes B<mergecap> to print a number of messages while it's working.
Print the version and exit.
=item -w E<lt>outfileE<gt>|-
Sets the output filename. If the name is 'B<->', stdout will be used.
This setting is mandatory.
To merge two capture files together, 100 seconds apart use:
capinfos -aeS a.pcap b.pcap
(Let's suppose a.pcap starts at 1009932757 and b.pcap ends
at 873660281. 1009932757 - 873660281 - 100 = 136272376
editcap -t 136272376 b.pcap b-shifted.pcap
mergecap -w compare.pcap a.pcap b-shifted.pcap
=head1 SEE ALSO
pcap(3), wireshark(1), tshark(1), dumpcap(1), editcap(1), text2pcap(1),
pcap-filter(7) or tcpdump(8)
B<Mergecap> is based heavily upon B<editcap> by Richard Sharpe
<sharpe[AT]ns.aus.com> and Guy Harris <guy[AT]alum.mit.edu>.
B<Mergecap> is part of the B<Wireshark> distribution. The latest version
of B<Wireshark> can be found at L<https://www.wireshark.org>.
HTML versions of the Wireshark project man pages are available at:
Scott Renfro <scott[AT]renfro.org>
Bill Guyton <guyton[AT]bguyton.com>