blob: 048717f57dc0478a75589dda7c7d9e263d42f910 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
|
I. Capturing packets with Wireshark/Tshark
There are two ways of installing Wireshark/Tshark on Debian:
I./a. Installing dumpcap without allowing non-root users to capture packets
Only root user will be able to capture packets. It is advised to capture
packets with the bundled dumpcap program as root and then run
Wireshark/Tshark as an ordinary user to analyze the captured logs. [2]
This is the default on Debian systems.
I./b. Installing dumpcap and allowing non-root users to capture packets
Members of the wireshark group will be able to capture packets on network
interfaces. This is the preferred way of installation if Wireshark/Tshark
will be used for capturing and displaying packets at the same time, since
that way only the dumpcap process has to be run with elevated privileges
thanks to the privilege separation[1].
Note that no user will be added to group wireshark automatically, the
system administrator has to add them manually. After a user is added
to the wireshark group she/he may need to log in again to make her/his new
group membership take effect and be able to capture packets.
The additional privileges are provided using the Linux Capabilities
system where it is available and resort to setting the set-user-id bit
of the dumpcap binary as a fall-back, where the Linux Capabilities system
is not present (Debian GNU/kFreeBSD, Debian GNU/Hurd).
Linux kernels provided by Debian support Linux Capabilities, but custom
built kernels may lack this support. If the support for Linux
Capabilities is not present at the time of installing wireshark-common
package, the installer will fall back to set the set-user-id bit to
allow non-root users to capture packets.
If installation succeeds with using Linux Capabilities, non-root users
will not be able to capture packets while running kernels not supporting
Linux Capabilities.
Note that capturing USB packets is not enabled for non-root users by using
Linux Capabilities. You have to capture the packets using the method
described in I./a., setting the set-user-id permanently using
dpkg-statoverride or running Wireshark as root.
The installation method can be changed any time by running:
dpkg-reconfigure wireshark-common
II. Installing SNMP MIBs
SNMP [4] OIDs can be decoded using MIBs provided by other packages.
wireshark-common suggests snmp-mibs-downloader which package can be used to
download a set of common MIBs Wireshark/Tshark tries to load at startup.
At the time of writing, MIBs are distributed under DFSG incompatible terms
[5] thus snmp-mibs-downloader has to be in the non-free archive area.
To keep wireshark in the main area [7], wireshark-common does not depend on
or recommend snmp-mibs-downloader and as a result snmp-mibs-downloader is
not installed automatically with wireshark.
To make Wireshark/Tshark able to decode OIDs, please install
snmp-mibs-downloader manually.
To help Wireshark/Tshark to decode OIDs without having to install packages
manually, please support the initiative of requesting additional rights
from RFC authors [5].
[1] https://wiki.wireshark.org/Development/PrivilegeSeparation
[2] https://wiki.wireshark.org/CaptureSetup/CapturePrivileges
[3] https://blog.wireshark.org/2010/02/running-wireshark-as-you
[4] https://wiki.wireshark.org/SNMP
[5] https://wiki.debian.org/NonFreeIETFDocuments
[6] https://www.debian.org/doc/debian-policy/ch-archive.html#s-non-free
[7] https://www.debian.org/doc/debian-policy/ch-archive.html#s-main
|
