diff options
Diffstat (limited to 'firmware/atmel_softpack_libraries/libchip_sam3s/include/pio.h')
-rw-r--r-- | firmware/atmel_softpack_libraries/libchip_sam3s/include/pio.h | 206 |
1 files changed, 206 insertions, 0 deletions
diff --git a/firmware/atmel_softpack_libraries/libchip_sam3s/include/pio.h b/firmware/atmel_softpack_libraries/libchip_sam3s/include/pio.h new file mode 100644 index 0000000..82fa388 --- /dev/null +++ b/firmware/atmel_softpack_libraries/libchip_sam3s/include/pio.h @@ -0,0 +1,206 @@ +/* ---------------------------------------------------------------------------- + * ATMEL Microcontroller Software Support + * ---------------------------------------------------------------------------- + * Copyright (c) 2010, Atmel Corporation + * + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * - Redistributions of source code must retain the above copyright notice, + * this list of conditions and the disclaimer below. + * + * Atmel's name may not be used to endorse or promote products derived from + * this software without specific prior written permission. + * + * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR + * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE + * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, + * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF + * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING + * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, + * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * ---------------------------------------------------------------------------- + */ + +/** + * \file + * + * \section Purpose + * + * This file provides a basic API for PIO configuration and usage of + * user-controlled pins. Please refer to the board.h file for a list of + * available pin definitions. + * + * \section Usage + * + * -# Define a constant pin description array such as the following one, using + * the existing definitions provided by the board.h file if possible: + * \code + * const Pin pPins[] = {PIN_USART0_TXD, PIN_USART0_RXD}; + * \endcode + * Alternatively, it is possible to add new pins by provided the full Pin + * structure: + * \code + * // Pin instance to configure PA10 & PA11 as inputs with the internal + * // pull-up enabled. + * const Pin pPins = { + * (1 << 10) | (1 << 11), + * REG_PIOA, + * ID_PIOA, + * PIO_INPUT, + * PIO_PULLUP + * }; + * \endcode + * -# Configure a pin array by calling PIO_Configure() with a pointer to the + * array and its size (which is computed using the PIO_LISTSIZE macro). + * -# Change and get the value of a user-controlled pin using the PIO_Set, + * PIO_Clear and PIO_Get methods. + * -# Get the level being currently output by a user-controlled pin configured + * as an output using PIO_GetOutputDataStatus(). + */ + +#ifndef _PIO_ +#define _PIO_ + +/* + * Headers + */ + +#include "chip.h" + +#include <stdint.h> + +/* + * Global Definitions + */ + +/* The pin is controlled by the associated signal of peripheral A. */ +#define PIO_PERIPH_A 0 +/* The pin is controlled by the associated signal of peripheral B. */ +#define PIO_PERIPH_B 1 +/* The pin is controlled by the associated signal of peripheral C. */ +#define PIO_PERIPH_C 2 +/* The pin is controlled by the associated signal of peripheral D. */ +#define PIO_PERIPH_D 3 +/* The pin is an input. */ +#define PIO_INPUT 4 +/* The pin is an output and has a default level of 0. */ +#define PIO_OUTPUT_0 5 +/* The pin is an output and has a default level of 1. */ +#define PIO_OUTPUT_1 6 + +/* Default pin configuration (no attribute). */ +#define PIO_DEFAULT (0 << 0) +/* The internal pin pull-up is active. */ +#define PIO_PULLUP (1 << 0) +/* The internal glitch filter is active. */ +#define PIO_DEGLITCH (1 << 1) +/* The pin is open-drain. */ +#define PIO_OPENDRAIN (1 << 2) + +/* The internal debouncing filter is active. */ +#define PIO_DEBOUNCE (1 << 3) + +/* Enable additional interrupt modes. */ +#define PIO_IT_AIME (1 << 4) + +/* Interrupt High Level/Rising Edge detection is active. */ +#define PIO_IT_RE_OR_HL (1 << 5) +/* Interrupt Edge detection is active. */ +#define PIO_IT_EDGE (1 << 6) + +/* Low level interrupt is active */ +#define PIO_IT_LOW_LEVEL (0 | 0 | PIO_IT_AIME) +/* High level interrupt is active */ +#define PIO_IT_HIGH_LEVEL (PIO_IT_RE_OR_HL | 0 | PIO_IT_AIME) +/* Falling edge interrupt is active */ +#define PIO_IT_FALL_EDGE (0 | PIO_IT_EDGE | PIO_IT_AIME) +/* Rising edge interrupt is active */ +#define PIO_IT_RISE_EDGE (PIO_IT_RE_OR_HL | PIO_IT_EDGE | PIO_IT_AIME) + +#ifdef __cplusplus + extern "C" { +#endif + +/* + * Global Macros + */ + +/** + * Calculates the size of an array of Pin instances. The array must be defined + * locally (i.e. not a pointer), otherwise the computation will not be correct. + * \param pPins Local array of Pin instances. + * \return Number of elements in array. + */ +#define PIO_LISTSIZE(pPins) (sizeof(pPins) / sizeof(Pin)) + +/* + * Global Types + */ + + +/* + * Describes the type and attribute of one PIO pin or a group of similar pins. + * The #type# field can have the following values: + * - PIO_PERIPH_A + * - PIO_PERIPH_B + * - PIO_OUTPUT_0 + * - PIO_OUTPUT_1 + * - PIO_INPUT + * + * The #attribute# field is a bitmask that can either be set to PIO_DEFAULt, + * or combine (using bitwise OR '|') any number of the following constants: + * - PIO_PULLUP + * - PIO_DEGLITCH + * - PIO_DEBOUNCE + * - PIO_OPENDRAIN + * - PIO_IT_LOW_LEVEL + * - PIO_IT_HIGH_LEVEL + * - PIO_IT_FALL_EDGE + * - PIO_IT_RISE_EDGE + */ +typedef struct _Pin +{ + /* Bitmask indicating which pin(s) to configure. */ + uint32_t mask; + /* Pointer to the PIO controller which has the pin(s). */ + Pio *pio; + /* Peripheral ID of the PIO controller which has the pin(s). */ + uint8_t id; + /* Pin type. */ + uint8_t type; + /* Pin attribute. */ + uint8_t attribute; +} Pin ; + +/* + * Global Access Macros + */ + +/* + * Global Functions + */ + +extern uint8_t PIO_Configure( const Pin *list, uint32_t size ) ; + +extern void PIO_Set( const Pin *pin ) ; + +extern void PIO_Clear( const Pin *pin ) ; + +extern uint8_t PIO_Get( const Pin *pin ) ; + +extern uint8_t PIO_GetOutputDataStatus( const Pin *pin ) ; + +extern void PIO_SetDebounceFilter( const Pin *pin, uint32_t cuttoff ); + +#ifdef __cplusplus +} +#endif + +#endif /* #ifndef _PIO_ */ + |