path: root/hardware/pcb
AgeCommit message (Expand)AuthorFilesLines
2019-09-03schematic: mark P1 and P2 as dot no placeKévin Redon1-0/+0
2019-09-03schematic: mark USB reset circuit as dot no placeKévin Redon1-0/+0
2019-09-03schematic: mark R19 as dot no placeKévin Redon1-0/+0
2019-09-03schematic: rename NP to DNP for clarityKévin Redon1-0/+0
2019-09-03schematic: mark JP1 and JP2 as dot no placeKévin Redon1-0/+0
2019-09-03schematic: mark R22 as dot no placeKévin Redon1-0/+0
2019-09-03schematic: mark R24 as no placeKévin Redon1-0/+0
2019-09-03schematic: mark R15 as no placeKévin Redon1-0/+0
2019-09-03schematic: make it more readableKévin Redon1-0/+0
2015-07-05change microcontroller to SAM3SKing Kévin15-58487/+58595
2014-06-26Update BOM for v1.4v1.4Harald Welte1-0/+0
2014-06-23export schematic, and pcb (with minor esthetic corrections)Kevin Redon23-87835/+948
2014-06-20v1.4: Connect PA0 to 3V3; pull-up for PA1/PA2 (R25,R26)Harald Welte14-1810/+2081
2013-11-11simtrace 1.3: move point of origin to lower left corner of PCBHarald Welte2-58/+58
2013-10-28mergeKevin Redon1-0/+0
2013-10-28BOM corrected (sorted by value) and reformatedKevin Redon1-56/+41
2013-10-27re-add BOM spreadsheet with updated v1.3 componentsHarald Welte1-0/+0
2013-10-27MCU pin 48 used to identify v1.3 by putting it to ground (with internal pull-up)Kevin Redon23-168215/+83608
2013-10-27exported fabrication filesKevin Redon39-182690/+148041
2012-05-19Mark IC5 as "do not place" (VCC_Forward) as it doesn't work anywayv1.2_productionHarald Welte1-0/+0
2012-05-18RST_PHONE pulldown added on PCBKevin Redon27-5124/+5849
2012-05-16v1.2p fabrication exportedKevin Redon27-101216/+87995
2011-12-06hw: fabrication output generatedv1.1_productionKevin Redon3-188/+187
2011-11-05hw: sysmocom added to copper, gerber renderedKevin Redon18-1713/+2148
2011-11-05hw: solder mask between at91sam7s addedKevin Redon21-34260/+40234
2011-07-02v1.0p corrected and rendered. BOM updatedv1.0_productionKevin Redon25-13737/+9722
2011-07-02D2 and D3 now also use STPS340U instead of 1N5819Kevin Redon2-18/+17
2011-07-02BOM updated for productionKevin Redon2-37/+37
2011-07-02PS/gerber rendered for productionKevin Redon24-18255/+19597
2011-06-23BOM updatedKevin Redon2-31/+28
2011-06-23PCB PS drawings were in the wrong folderKevin Redon14-164700/+3695
2011-06-23ps/gerber rerendered for the thermal footprintsKevin Redon20-98/+170392
2011-06-21v1.0 released. board version added, output (schema,gerber) renderedKevin Redon20-77952/+192014
2011-06-21wrong USB connector from digikey in BOM chosen. corrected : hirose UX60-MB-5S...Kevin Redon1-0/+0
2011-06-21output renderedKevin Redon26-124805/+80638
2011-06-20BOM updated, partiallyKevin Redon1-0/+0
2011-06-20LDO, and power switch added. not verified yetKevin Redon1-0/+0
2011-06-20bus switch CB3q3244 used instead of QS3244Kevin Redon1-0/+0
2011-06-20USB changed, BOM updatedKevin Redon1-0/+0
2011-06-15USB_PUP all whole board reroutedKevin Redon2-3875/+5127
2011-05-22debug port changedKevin Redon17-14767/+12289
2011-05-17board reroutedKevin Redon17-256529/+115257
2011-05-15pcb drawings & gerber addedKevin Redon19-0/+362335