summaryrefslogtreecommitdiffstats
path: root/src/target/firmware/board/gta0x/init.c
blob: 584209474d04dc3b7cf4a51e3ee1c0b218b04197 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
/* Initialization for the Openmoko Freerunner modem */

/* (C) 2010 by Harald Welte <laforge@gnumonks.org>
 *
 * All Rights Reserved
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License along
 * with this program; if not, write to the Free Software Foundation, Inc.,
 * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
 *
 */

#include <stdint.h>
#include <stdio.h>

#include <debug.h>
#include <ctors.h>
#include <memory.h>
#include <board.h>
#include <keypad.h>
#include <console.h>
#include <flash/cfi_flash.h>
#include <tiffs.h>

#include <calypso/irq.h>
#include <calypso/clock.h>
#include <calypso/dma.h>
#include <calypso/rtc.h>
#include <calypso/timer.h>
#include <uart.h>
#include <calypso/backlight.h>

#include <comm/sercomm.h>
#include <comm/timer.h>

#include <abb/twl3025.h>
#include <rf/trf6151.h>
#include "../compal/keymap.h"

#define ARMIO_LATCH_OUT 0xfffe4802
#define IO_CNTL_REG	0xfffe4804
#define ASIC_CONF_REG	0xfffef008
#define IO_CONF_REG	0xfffef00a

static void board_io_init(void)
{
	uint16_t reg;

	reg = readw(ASIC_CONF_REG);
	/* TWL3025: Set SPI+RIF RX clock to rising edge */
	reg |= (1 << 13) | (1 << 14);
	writew(reg, ASIC_CONF_REG);

	/*
	 * Most Calypso peripheral interface signals are unconnected
	 * on this modem.  We configure them to be GPIOs in IO_CONF_REG,
	 * then configure them to be outputs in IO_CNTL_REG, then set
	 * the outputs to 0 in ARMIO_LATCH_OUT.
	 */
	writew(0x03F5, IO_CONF_REG);
	writew(0xC000, IO_CNTL_REG);
	writew(0x0000, ARMIO_LATCH_OUT);
}

void board_init(int with_irq)
{
	/* Configure the memory interface */
	calypso_mem_cfg(CALYPSO_nCS0, 3, CALYPSO_MEM_16bit, 1);
	calypso_mem_cfg(CALYPSO_nCS1, 3, CALYPSO_MEM_16bit, 1);
	calypso_mem_cfg(CALYPSO_nCS2, 5, CALYPSO_MEM_16bit, 1);
	calypso_mem_cfg(CALYPSO_nCS3, 5, CALYPSO_MEM_16bit, 1);
	calypso_mem_cfg(CALYPSO_CS4, 0, CALYPSO_MEM_8bit, 1);
	calypso_mem_cfg(CALYPSO_nCS6, 0, CALYPSO_MEM_32bit, 1);
	calypso_mem_cfg(CALYPSO_nCS7, 0, CALYPSO_MEM_32bit, 0);

	/* Set VTCXO_DIV2 = 1, configure PLL for 104 MHz and give ARM half of that */
	calypso_clock_set(2, CALYPSO_PLL13_104_MHZ, ARM_MCLK_DIV_2);

	/* Configure the RHEA bridge with some sane default values */
	calypso_rhea_cfg(0, 0, 0xff, 0, 1, 0, 0);

	/* Initialize board-specific GPIO */
	board_io_init();

	/* Enable bootrom mapping to route exception vectors to RAM */
	calypso_bootrom(with_irq);
	calypso_exceptions_install();

	/* Initialize interrupt controller */
	if (with_irq)
		irq_init();

	sercomm_bind_uart(UART_MODEM);
	cons_bind_uart(UART_IRDA);

	/* initialize MODEM UART to be used for sercomm */
	uart_init(UART_MODEM, with_irq);
	uart_baudrate(UART_MODEM, UART_460800);

	/* Initialize IRDA UART to be used for old-school console code.
	 * note: IRDA uart only accessible on C115 and C117 PCB */
	uart_init(UART_IRDA, with_irq);
	uart_baudrate(UART_IRDA, UART_115200);

	/* Initialize hardware timers */
	hwtimer_init();

	/* Initialize DMA controller */
	dma_init();

	/* Initialize real time clock */
	rtc_init();

	/* Initialize system timers (uses hwtimer 2) */
	timer_init();

	/* Initialize LCD driver (uses I2C) and backlight */
	bl_mode_pwl(1);
	bl_level(50);

	/* Initialize keypad driver */
	keypad_init(keymap, with_irq);

	/* Initialize ABB driver (uses SPI) */
	twl3025_init();

	/* Initialize TIFFS reader (7 sectors of 64 KiB each) */
	tiffs_init(0x380000, 0x10000, 7);
}