Age | Commit message (Collapse) | Author | Files | Lines |
|
Each ARFCN channel may be independently configureted and possibly on
separate hardware, so don't share a single vector for noise estimate
calculations. Allow a non-pointer based iterator so we can get away
with using the default copy constructor.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Separate the large pullRadioVector() call, which forms the central
portion of the receive path burst processing. Break out RACH, normal
burst, and demodulation into separate methods. This makes the burst
handling from the FIFO read to soft bit output somewhat more
manageable.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This patch allows multiple signalVectors to be stored within
a single radioVector object. The motivation is to provide
a facility for diversity and/or MIMO burst handling. When
no channel value is specified, single channel bevhaviour
is maintained.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
The transceiver and underlying device drivers are threaded. use
the following priority levels.
0.50 - UHD driver internal threads
0.45 - Receive device drive thread
0.44 - Transmit device drive thread
0.43 - UHD asynchronous update thread (error reporting)
0.42 - Receive burst processing thread(s)
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This patch primarily addresses devices with multiple RF front end
support. Currently device support is limited to UmTRX.
Vectorize transceiver variables to allow multiple asynchronous
threads on the upper layer with single downlink and uplink threads
driving the UHD I/O interface synchronously.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Collect the slot information into an indpendent state object. This
will allow us to easily create multiple instances of internal state
variables without having to replicate the transceiver object itself.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
For multiple transceiver connections, it is inappropriate to
allocate all sockets in the transceiver constructor due to not
knowing how many connections are avaialble in advance and for
error checking purposes. Instead, store the base socket address
port combination and setup the sockets in the initialization
call.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
The current status and operability of this compile option is
unknown. Remove due to lack of use, demand, and maintenance.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Previous removal of the energy detector requirement broke
the noise level calculation loop. The previous adaptive
approach was finicky - noticably at high gain levels. Since
we no longer use the energy threshold for primary burst gating,
we can return to a simpler world.
In the new approach, we compute a running average of energy
levels and track them with a noise vector. A timeslot that
passes the correlator threshold is a valid burst. These are
not used in the noise calculation. Everything else is
considered noise and used to compute the noise level with
respect to full scale input level, which for almost all
supported devices is 2^15.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This patch applies oversampling, when selected with 4 sps,
to the downlink only, while running the receiver with
minimal sampling at 1 sps. These split sample rates allow
us to run a highly accurate downlink signal with minimal
distortion, while keeping receive path channel filtering
on the FPGA.
Without this patch, we oversample the receive path and
require a steep receive filter to get similar adjacent
channel suppression as the FPGA halfband / CIC filter
combination, which comes with a high computational cost.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
This patch primarily addresses observed repeated overrun
conditions in embedded environments - namely ARM.
The heartbeat of the transceiver is derived from the receive
sample stream, which drives the main GSM clock. Detach the
transmit thread from the receive loop to avoid interfering with
the receive I/O, which is sensitive to overrun conditions if
pull process is interrupted.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
There is no reason expose the pulse shaping filter outside of the
signal processing calls. The main transceiver object makes no use
of the filter and there's no reason to pass it around.
Initialize the pulse shape with the signal processing library, and
maintain an internal static member like many of the other library
variables. Similarly destroy the object when the library is closed.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Because repeatedly typing mSamplesPerSymbol is giving me
carpal tunnel syndrome. Replace with the much shorter,
easier to type, and just as clear name of 'sps'.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
|
|
Submitted by: Ivan Kluchnikov <kluchnikovi@gmail.com>
Signed-off-by: Thomas Tsou <tom@tsou.cc>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@5690 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Submitted-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Thomas Tsou <tom@tsou.cc>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@5677 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
Push the ability to set thread priority out to the 52M
Transceiver interface, because that's where the thread
control exists.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2644 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|
|
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2307 19bc5d8c-e614-43d4-8b26-e1612bc8e597
|