aboutsummaryrefslogtreecommitdiffstats
path: root/example
AgeCommit message (Collapse)AuthorFilesLines
2018-11-30Add and use compatible scenario when testing IPA dynts with nanoBTSPau Espin Pedrol2-2/+15
nanoBTS doesn't support SDCCH8 in TS!=1 according to osmo-bsc code. Let's use in this case TCH/H to make sure they are not used for the test (since we require osmo-bsc to use full rate codecs for the call). Change-Id: I37f3fe813d4074fbfe64ff3176048e7d25d470e2
2018-11-23resources.conf: Set UHD identifiers on B200 devicesPau Espin Pedrol2-1/+3
osmo-trx-uhd uses these args during device search/selection process. As those were not set until now for B200, it means when a B200 was used by osmo-gsm-tester any UHD device could be picked up and used by UHD. That was actually happening since inclusion of UmTRX devices in Prod setup, when running tests against desired B200, actually the UmTRX device was being used. Change-Id: I696bbc800b05fdd9a68a77f363d76dcc53ef24ee
2018-11-19resources.conf.rnd: gobi2k changed by ec20Pau Espin Pedrol1-3/+3
Given current bad support of most features used, gobi2k modem was removed and an EC20 was added instead. Change-Id: I2df38547978c7d2b1a1309f6e73b5a59413e08ff
2018-11-18default-suites: Enable tests for LimeSDR-USBPau Espin Pedrol1-0/+20
Change-Id: I896ea76f1d2847ec014a62c87220d184b95d1dd2
2018-11-09default-suites: Add tests for UmTRXPau Espin Pedrol1-0/+20
Change-Id: I0d0fe17676550a96d9bcf795faf43f7e6b82fb1a
2018-11-09resurces.conf.prod: Add UmTRX devicePau Espin Pedrol2-0/+18
Change-Id: I11f3275bddcc1c0c5bcd75e6a32f040a8f7c1174
2018-11-06resources.conf.prod: Update modem info after HW upgradePau Espin Pedrol1-5/+33
A new quadmodem with 4xEC20 has been added to the Prod setup. Change-Id: I51f0b7dd7a1857d34fc2c5076016caeffa15240d
2018-10-31resources.conf: ec20: Enable voice supportPau Espin Pedrol2-2/+2
It was tested that it could do MO and MT voicecall just fine as SierraW modems. Change-Id: Ie14c00f9f80e00fdbb52ab82a53b4b5a187d41e7
2018-10-31default-suites.conf: Enable testing egprsPau Espin Pedrol1-0/+5
Change-Id: I1885e2a749e62547f60b9c35e15f1277b2627bb4
2018-10-31Add support to enable EGPRSPau Espin Pedrol2-0/+4
Change-Id: I682f0c1b4cb97b704d646f18f54e748baaefd677
2018-10-31resources.conf: Add extra IPaddr to poolPau Espin Pedrol2-0/+2
Change-Id: If0f1a6a3f4e99091ed117bc7a77a5e60eccb2425
2018-10-31Add support to test gprs IPv4 data planePau Espin Pedrol2-6/+6
Since the modem iface and the GGSN iface are on the same host/netns, it's really difficult to conveniently test data plane without getting routing loops. As a result, either GGSN or modem iface must be moved to a different namespace. The decision after a few discussions was finally to move modem interfaces to a different netns. Expected setup: * ofono is patched to avoid removing modem if it detects through udev that its net iface was removed (due to for instance, net iface being moved to another netns and thus not being reachable anymore by systemd-udev process running in root netns). * After ofono is started (and successfully configured all the modems and detected its net ifaces through syfs/udev), script "modem-netns-setup.py start" which creates a netns for each modem, naming it after its usb path ID. net ifaces for that modem are moved into its netns. * Modem is configured to use 802-3 data format, and as a result the net iface is configured through DHCP (DHCP req only replied AFTER pdp ctx is activated!). * Since osmo-gsm-tester knowns the modem USB path ID (available in resources.conf), it can run required steps (ifup, DHCP) to configure the interface. The interface name is provided by ofono to osmo-gsm-tester. * As a result, any process willing to transmit data through the modem must be in the modem netns. Related: OS#2308 Change-Id: Icb06bdfcdd37c797be95ab5addb28da2d9f6681c
2018-10-30default-suites.conf: Make sure we use fr codec with IPA dyn TSPau Espin Pedrol2-13/+20
IPA style dynamic timeslots (TCH/F_PDCH) support only TCH/F and thus only full rate codecs are to be used. On the other hand, OSMO style dynamic timeslots (TCH/F_TCH/H_PDCH) can use both full rate and half rate, so no need to be restrictive there. Change-Id: I0039ef60b323ed72cfe00d8fd9e9287e9c82d49f
2018-10-30default-suites: Remove .conf suffic from scenariosPau Espin Pedrol1-8/+8
Change-Id: I090a3ba8c5eb8fc256f09c798bfb5a17cdca274e
2018-10-29defaults.conf: Set valid default codec_list matching avail TS typesPau Espin Pedrol1-1/+1
By default, all channels are TCH/F, and as a result we cannot run half rate codecs on it. Since recent versions of osmo-bsc, it checks this kind of misconfigurations and answers with an Assignment Failure: .... 20181029162133430 DMSC <0007> codec_pref.c:445 codec-support/trx config of BTS 0 does not intersect with codec-list of MSC 0 20181029162133430 DMSC <0007> osmo_bsc_main.c:887 Configuration contains mutually exclusive codec settings -- check configuration! .... 20181029162255253 DMSC <0007> osmo_bsc_bssap.c:859 Rx MSC DT1 BSSMAP ASSIGNMENT REQ 20181029162255254 DMSC <0007> osmo_bsc_bssap.c:718 No supported audio type found for channel_type = { ch_indctr=0x1, ch_rate_type=0xa, perm_spch=[ 42 21 11 01 25 05 ] Change-Id: Ie6b37839fe363b5d1ba64c267d751221434cdedb
2018-10-10osmo-bts-trx: Add support for osmo-trx-lmsPau Espin Pedrol2-0/+18
Change-Id: I44db0fe4592109ecb665e1880806d90379da64f7
2018-10-09resources.conf.prod: Update TRX host ip addrPau Espin Pedrol1-1/+1
The host was updated to have several IP address to be able to run several instances of osmo-trx in parallel. Change-Id: I3595b82a5d202caec7bc48a63e28ce0331e5abb7
2018-10-04defaults.conf: Add SDCCH8 ts in TRX1 cfgPau Espin Pedrol1-1/+1
This way we can test too if SDCH8 channels are allocated and used correctly in TRX1 in multiTRX setups. Change-Id: I9d08f3d019a28cf775d70d941c5a60a7e7ca20a9
2018-10-03default-suites.conf: Add test to check multiTRX with Ettus B200Pau Espin Pedrol1-0/+2
Change-Id: Ied768938851488c3f502b2d41334afa17f7f5401
2018-10-02osmo-trx: Enable multi_arfcn for B200 and only in multiTRX setupPau Espin Pedrol2-0/+2
Change-Id: I6a29e1813f0603b00b49b7b7c805be23a72cf0e3
2018-10-02resources.conf.prod: Use specific remote machine to run osmo-trxPau Espin Pedrol1-0/+2
Run osmo-trx in a separate more powerful machine (i5) rather than running in low end APU where osmo-gsm-tester runs. Change-Id: I0479643789783d5e8a142042a65c4d53020d1e79
2018-10-02osmotrx: Allow running osmo-trx from remote hostPau Espin Pedrol1-0/+2
Change-Id: Ia31ac8eb41e02eda28d9f6f56774679300244ee8
2018-09-25default-suites.conf: Add empty lines to easily spot different sectionsPau Espin Pedrol1-0/+5
Change-Id: If33fa9be091113d57b25dc3d73e277bbb3b0ce5a
2018-09-25Add dynts suite to test switch between PDCH and TCHPau Espin Pedrol3-0/+34
It seems for not yet clear reasons the MS require some time after the PDCH channels have been activated again to use them reliably. If no sleep is used between call hangup and gprs activate pdp ctx, the MS fails to activate the pdp ctx due to QMI error respone to the "Start network" requested. Related: OS#2582 Change-Id: I73b51c31309ac4c28c64ed7eb7c8c649e535aa22
2018-09-18default-suites: Remove nanobts HR1 voice testPau Espin Pedrol1-2/+0
nanobts doesn't support this codec, so it will always fail. Change-Id: Iea4e6395809e5ef5485892f8f17e0dcfa36640dc
2018-09-18osmo-trx: Add multi_arfcn supportPau Espin Pedrol1-1/+1
2nd TRX arfcn is changed in defaults.conf because multi_arfcn requires them to be alocated in steps of 4 starting from TRX0. It is not enabled by default yet on B200 (it must use it to support several TRX) because current host running osmo-gsm-tester is not performant enough and cannot keep up with timers due to multi-arfcn CPU overhead. Change-Id: I096df82ad1f4cbb41dfbd6a78466a845f34be385
2018-09-18osmo-bts-trx: Add multiTRX supportPau Espin Pedrol1-0/+3
Support is limited to 1 osmo-trx with 1 phy and multiple instances. Change-Id: If2bda5ec7ac9fa3fe6bc5d71f323c3ccc2a70158
2018-09-17Sanitize existing suite namesPau Espin Pedrol1-13/+13
When first suites were added, osmo-nitb was used. Then new tests using regular split components were added with "aoip_" prefix. At some point it was clear that osmo-nitb was being deprecated so new tests for split components were added without any prefix, as they are expected to be the default one. Since most current and future development is going to be done for split components, as well as new tests added, it makes sense to move the few old testsuites using osmo-nitb to have all "nitb_" prefix, while keeping the split component tests without prefix as it's the regular network topology. Change-Id: Idea2e053d337548e0e9b1b47441dbb262124f909
2018-09-04Remove tests for unspecified speech HR2Pau Espin Pedrol2-10/+0
HR2 was never specified, so there's no sense in attempting to test it. Change-Id: Ifd7cab43bae0729106a9402e3e610eeecde645e4
2018-08-29osmo-bts-trx: Big refactor and cleanup of osmo-trx related codePau Espin Pedrol3-3/+16
* This commit is a preparation for future commits to add support for different osmo-trx devices and backends like osmo-trx-lms. * Drop deprecated osmo-trx-* cmd line params and use VTY cfg to set them. * As number of osmo-trx related osmo-gsm-tester attributes grow, group them togther in an "osmo_trx" dictionary. Change-Id: I77d29413c9e3b600b796627ba366f80c3281b7e1
2018-08-29default-suites: Remove octobts testsPau Espin Pedrol1-11/+0
Since latest release firmware, we have been unable to start up octobts correctly. As it's annoying having all those tests failing all the time, let's disable them in nightly builds until we have a working OctoBTS setup working again. Change-Id: I828723193564b3a91aeac0c163c7c8c6b7e4058c
2018-08-29default-suites: Add suites testing different codecsPau Espin Pedrol1-12/+36
Change-Id: I591c71c66c5bbcd07466fe1d433aa87aed964fbe
2018-08-29osmo-bsc: Parametrize codec-list VTY cfgPau Espin Pedrol7-0/+32
Change-Id: I1678aba43e8d399ecad192cbc416698373e3c0a0
2018-08-23Add testsuite + scenarios to test nanoBTS multiTRXPau Espin Pedrol3-2/+18
Currently only 2 nanoBTS in the 900 band are attached together as a multiTRX setup. We thus set num_trx to 2 and set channel allocator descending to force the BTS to use the 2nd TRX when allocating channels. Change-Id: I12e1bcb047c4efac5693cf725739e0ce2e0532ee
2018-08-22Add channel_allocator cfg attr to bts resourcesPau Espin Pedrol1-0/+1
Change-Id: I682809d4aeb91a36e3a35fc481e8d40d0b084fa0
2018-08-21Replace suites dyn_ts_ipa* and voice using scenario modifiersPau Espin Pedrol5-14/+80
Now that we support modifiers in scenario files, we don't need to duplicate tests and testsuites to dynamically set trx configuration at run time. It can be done more easily with scenario modifiers. Change-Id: I80c441bb5b98d5d2e95d4c6ae1efab3e5f3c40d9
2018-08-21Introduce scenario modifiersPau Espin Pedrol1-0/+3
Before this patch, scenarios were only used to select resources with specific attributes. This commit introduces "modifiers" in scenarios, which allows setting or modifing config attributes of resources once they have been reserved. This way same test can be run selecting same resources but modifying its configuration, allowing for instance running different number of TRX, different timeslot configuration, etc. Modifiers are described by placing a "modifiers" dictionary in any scenario file, similar to the current "resources" one used to select requird resources. The "modifiers" dictionary is overlaid on top of the "resources" one resulting from combining all the "resources" dictionary of all scenario files. Change-Id: If8c422c67d9a971d9ce2c72594f55cde2db7550d
2018-08-10resources.conf.prod: Update modem paths after HW setup changesPau Espin Pedrol1-4/+4
Change-Id: I8673af3e9447b8093bc61503f9354a8f0431620e
2018-07-27nanobts: Support multiTRXPau Espin Pedrol3-15/+27
num_trx is left for now by default to 1, but it has been tested to work properly (current tests pass and both trx are configured) with num_trx=2. Change-Id: Ib3962f824a804e2aa582601475a8514c6cb0d8e7
2018-07-25Add ttcn3-bts-test envPau Espin Pedrol2-0/+6
Change-Id: I3251a49503dc823f0ef1fe8ef5d68236a584dad4
2018-06-26resources.conf: Move nanobts address to differentiate them from local IPsPau Espin Pedrol2-3/+3
nanobts IP addresses are assigned through DHCP, and are not local to the main unit. Let's use another subset for this DHCP pool as we usually use .50ish for static local IP addresses. Change-Id: Ibdb0dd97a490aaa555a7bf53cf43cc5a5533a012
2018-05-08default-suites.conf: Fix typo in previous commitPau Espin Pedrol1-2/+2
Change-Id: Ib1903324df8eb9f506b62dc0b9d2aa4a4a5179d7
2018-05-08default-suites.conf: Add dyn ts suitesPau Espin Pedrol1-0/+8
Change-Id: Iec7c8d8c3617f11a5ee12c02bd75ed6822d76aa9
2018-05-08bts: Allow setting amount of TRX and timeslot in cfg and from test at runtimePau Espin Pedrol1-0/+17
The num_trx attribute for a given BTS states the number of TRX to be used by that BTS. If more than num_trx are configured in trx_list in the cfg file, then only up to num_trx are taken into account. If a num_trx value higher than max_trx is specified throuygh config file or at runtime by the test, an exception is raised explaining the issue. The num/max_trx attributes are overlayed along the config levels (generic -> bsc_bts -> specific bts-type -> specific resource object). This way we can specify a long list of trx+timeslot config in the generic config (bsc_bts), and tune for each model and specific BTS which is the desired default number of TRX, as well as the maximum supported per type. Change-Id: I7f46eaf7a16f03268653299c93600c0443f691ac
2018-03-27example: Run tests on both nanobts with different bandsPau Espin Pedrol1-5/+10
Change-Id: Iee2220e1770caa891713dbd18e8f4a4741c1fbe4
2018-03-27nanobts: Add support to run nanobts on the 900 bandPau Espin Pedrol3-6/+12
Change-Id: I13b494630ea835f4bed38ccc77f6a4d5e18326af
2018-03-27example: Add scenarios to select BTS for a specific bandPau Espin Pedrol3-0/+9
Change-Id: Id830536c9337151818901cb25c3a568a77cdbf5e
2018-03-27nanobts: Bind to specific addr instead of specific ifacePau Espin Pedrol2-2/+0
This way root access is not required. Change-Id: I02f6fc9e1cb1ea1e1d950eafe22c231a18100f98
2018-03-15default-suites.conf: Add nanobts related testsPau Espin Pedrol1-0/+6
Change-Id: I054db78e6a71514133e4e3c3158342b74af44201
2018-03-15Introduce ip.access nanobts supportPau Espin Pedrol4-0/+29
Change-Id: Ibaea025b3a503dfe897d36701234445de6d49f82
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-26 09:15:05 +0000