| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The sysmoBTS2050 does not have a OCXO and we should not rely
on the GPS module to always have a fix. Instead use the TCXO
by default and from time to time (and we know we have a fix
calibrate the TCXO). This can be done by:
trx 0 rf-clock-info reset
wait...
trx 0 rf-clock-info correct
write
The output is currently only written to the log as the VTY
connection might go away during the operation. The reset will
set the approriate reference clock and the correct will attempt
to determine and apply the correction. The write terminal will
make sure that next on start a known good value will be used.
|
|
In the perf the ARM EABI ddiv operation showed up in the most
of expensive symbols. It doesn't really make much sense as the
calls should only be done on configuration.
|
|
Use the lchan->rel_act_kind field for the BCCH activatiob by OML.
The lchan's should be marked as active but no event should be sent to
the BSC. This is mostly like the PCU. We can now remove the secnd
argument from lchan_activate.
|
|
This is used in the sysmoBTS 2050, where the maximum power is 40 dBm
We might want to add a safeguard of some kind to prevent people from
overdriving their transmitters.
|
|
The TRX nominal output power (as seen by OML) is the aggregate power
of any gain internal to the sysmoBTS (and managed by L1) and any
external PA. This is what is used in trx->nominal_power;
fl1h->l1_power is the transmit power to which we configure the sysmoBTS
L1. This is 23 dBm (200mW) by default in the sysmoBTS 1002, and 40 dBm
(5W) in the sysmoBTS 2050. However, if sysmoBTS 2050 is used in
single-TRX configuration, it may be used with higher power, which we can
now configure in the config file / vty.
TODO: A separate, additional field that keeps track of any gain added by
an external PA, e.g. if the sysmoBTS 1002 is used with a sysmoAMP.
|
|
By default read the clock calibration from the EEPROM. It is
still possible to set it using the cli.
Signed-off-by: Nicolas J. Bouliane <nicolas.bouliane@nutaq.com>
|
|
sysmobts_vty.c: In function 'activate_lchan':
sysmobts_vty.c:373:3: warning: implicit declaration of function 'lchan_activate' [-Wimplicit-function-declaration]
sysmobts_vty.c:375:3: warning: implicit declaration of function 'lchan_deactivate' [-Wimplicit-function-declaration]
eeprom.c: In function 'eeprom_ReadEthAddr':
eeprom.c:305:5: warning: pointer targets in passing argument 3 of 'eeprom_read' differ in signedness [-Wpointer-sign]
eeprom.c:260:12: note: expected 'char *' but argument is of type 'uint8_t *'
|
|
During development one switches from GSM900 to GSM1800 and GSM850 to
GSM1900. This commit attempts to make this switch more easy.
GSM1800 and GSM1900 have overlapping ARFCNs. This means that the
mapping from bands to arfcn is not injective. Because of that I
removed the code to deduce the band from the ARFCN. This was done
in commit 8c3d807b3fc785ffb18aeb97355150c92221e8a0. The auto-band
option allows to move between GSM900/GSM1800 and GSM850/GSM1900.
Add a simple testcase with these auto-band configurations.
|
|
When not specifying a config path, then saving the running config
it would end up as "(null)" and then leads to an error like this:
<0006> calib_file.c:147 Failed to open '(null)/calib_rxu_850.cfg' for calibration data.
Add a NULL check to avoid this issue when writing the config file.
|
|
Put all SAPI requests into a queue and handle them one after another.
Begin with the channel activation. Once the queue is empty the channel
activate will be sent. For the BCCH activation we do not want to send
a channel activation message and this is why we set the lchan->state
to NONE.
One change is that we do not attempt to call the ciphering routines on
the BCCH anymore.
This change is necessary to fix issues with LCHANs staying open and being
marked as broken by the BSC and will help in implementing handover support
as this requires a re-configuration of the lchan on the fly.
|
|
|
|
|
|
We used to have -75 dBm as the target value for the uplink receive
level. Now this is configurable.
The parameter is used as input into the power control loop that adjusts
the MS transmit power in order to achieve the target rx value on the
BTS Rx input.
|
|
'trx-calibration-path' is the new VTY command indicating the path
name where the calibration files can be found.
Calibration is only implemented for SUPERFEMTO API version 2.4.0 or
later.
|
|
libosmocore 40832fcfb58c8c97c66e098c5705352ac5beea8e and later contain
the vty_cmd_string_from_valstr() function, so we shouldn't have
a local / deprecated copy anymore.
|
|
Introduce femtobts_tracef_docs with some more information about
the traceflags, add parameters to the vty_cmd_string_from_valstr
for specifying the separator, the suffix and if the name should
be lowered.
|
|
|
|
In v2 the calibration value is the clock error in ppb that needs
to be compensated. Create a V2 specific implementation. Write the
clock value unconditionally as it is initialized to 0 by default
and not 0xffff.
|
|
We need to have a documentation for each possible value, add some simple
ones for the available clock sources.
|
|
Make the clock names lower case to match with the vty command.
|
|
this allows the BTS to loop-back any incoming data on a TCH
|
|
this allows for quick manual tx power changes from the VTY, particularly
useful in type approval or other measurements.
|
|
|
|
This allows us to do RF measurements (EDGE EVM and the like) even
without having any PCU/RLC/MAC code as of now.
To use it, configure PDCH type timeslots (e.g. TS 7) in the BSC and then
use "trx 0 7 activate 0" to manually activate the PDTCH lchan on top
of that timeslot. The BTS will now happily transmit EDGE/8PSK data.
|
|
This code would break in case we shrink the bitmap, use sizeof instead.
|
|
there are VTY commands that can be used to filter which particular
L1 sapis (channel types) should be sent in GSMTAP.
|
|
the default source is the OCXO
|
|
The first one just sets the val to 0xffff, the second converted
the value to integer twice.
sysmobts_vty.c: In function ‘cfg_trx_clkcal_def’:
sysmobts_vty.c:109:15: warning: unused variable ‘clkcal’ [-Wunused-variable]
sysmobts_vty.c: In function ‘cfg_trx_clkcal’:
sysmobts_vty.c:122:15: warning: unused variable ‘clkcal’ [-Wunused-variable]
|
|
|
|
this deals with unused cocde, unused variables and undeclared symbols in
various places.
|
|
|
|
|
