blob: 43b2458ec30c778ceb6b908ecd40836d22e9d10d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
|
##############################################################################
#
# Sample sgsnemu configuration file
#
##############################################################################
# TAG: debug
# Include this flag to include debug information.
#debug
# TAG: conf
# Configuration file to use. This file is the configuration file,
# so changing this parameter in the configuration file does not make
# sense. Use it on the command line instead.
# TAG: pidfile
# File to store information about the pricess id of the program.
# The program must have write access to this file/directory.
#pidfile ./sgsnemu.pid
# TAG: statedir
# Directory to use for nonvolatile storage.
# The program must have write access to this directory.
#statedir ./
# TAG: dns
# DNS server to use for ns lookups.
# If this tag is not set the system default DNS will be used.
#dns 10.1.2.3
# TAG: listen
# Specifies the local IP address to listen to
#listen 10.0.0.217
# TAG: remote
# Specifies the remote IP address to connect to
# If DNS is setup correctly it should be possible to specify the
# access point name (APN) as the remote address.
#remote 10.0.0.240
# TAG: contexts
# Number of contexts to establish from the emulator to the ggsn.
# Set this tag to zero to not establish any contexts.
#contexts 1
# TAG: timelimit
# Disconnect contexts after timelimit seconds, and exit the program.
# Setting timelimit to zero will cause the program not to disconnect.
#timelimit 0
# TAG: apn
# Access point name to connect to when run in client mode.
#apn internet
# TAG: selmode
# Selection mode to use when connecting to GGSN.
#selmode 0x01
# TAG: imsi
# IMSI number used when run in client mode.
#imsi 2400101234567890
# TAG: msisdn
# MSISDN number used when run in client mode.
#msisdn 46702123456
# TAG: qos
# Requested Quality of Service used when run in client mode.
# 3 bytes corresponding to ????
#qos 0x0b921f
# TAG: uid
# User ID used when run in client mode.
#uid mig
# TAG: pwd
# Password used when run in client mode.
#pwd hemlig
# TAG: createif
# Use this flag if you want to set up a local network interface after
# a PDP context has been established.
#createif
# TAG: defaultroute
# Use this flag if you want to add a default route after a network interface
# had been established.
#defaultroute
# TAG: ipup
# Script executed after network interface has been brought up.
# Executed with the following parameters: <devicename> <ip address>
#ipup /etc/sgsnemu/ip-up
# TAG: ipdown
# Script executed after network interface has been taken down.
# Executed with the following parameters: <devicename> <ip address>
#ipdown /etc/sgsnemu/ip-down
# TAG: pinghost
# Ping a remote host through a PDP context by using ICMP echo messages.
# If more than one PDP context has been established the ICMP messages will
# be distributed between all available contexts.
#pinghost 192.168.0.0
# TAG: pingrate
# Number of ping messages to send off each second.
#pingrate 1
# TAG: pingsize
# Size of ICMP echo message payload. Add 28 to get the full IP packet size.
#pingsize 56
# TAG: pingcount
# Number of ping messages to send off.
#pingcount 0
# TAG: pingquiet
# Do not print ping packet info.
#pingquiet
|
