Age | Commit message (Collapse) | Author | Files | Lines |
|
Currently the parser functions for single information elements are
defined within gprs_gb_parse.c and not exported explicitely. In
addition they are named like libosmocore's TLV parser functions and
do not have a proper name prefix. Since it is planned to use them for
other protocols, they need to be globally accessible.
This patch moves them to gprs_utils.c and renames them.
The new names are:
lv_shift -> gprs_shift_lv
v_fixed_shift -> gprs_shift_v_fixed
lv_shift -> gprs_shift_lv
v_fixed_shift -> gprs_shift_v_fixed
In the long term, these functions should be moved to libosmocore (and
renamed again).
Sponsored-by: On-Waves ehf
|
|
This commit mainly extends sgsn_auth.c to use and support the
auth_state SGSN_AUTH_AUTHENTICATE. It will be activated when IMSI and
IMEI are available, authentication is required
(subscr->sgsn_data->authenticate is set), but the MM context is not
marked as authenticated. If the state has been set to
SGSN_AUTH_AUTHENTICATE and sgsn_auth_update() is called, the GMM
layer will be informed by invoking gsm0408_gprs_authenticate().
Sponsored-by: On-Waves ehf
|
|
The test didn't test that the access-list has been properly
removed. Fix the test to only remove the list once and verify
that it is gone.
|
|
This adds the following commands to the ENABLE node:
- show subscriber cache
- update-subscriber imsi IMSI insert authorized (0|1)
- update-subscriber imsi IMSI cancel
- update-subscriber imsi IMSI commit
These commands are mainly testing tools and maintenance helpers. The
update commands work asynchronously and can be used to complete a
pending update request or to terminate an existing connection. The
'insert' command just update the subscriber records but does not
notify the GMM layer. Invoke the 'commit' command to continue with
pending procedures.
Note that the subscriber cache is not stored persistently and will
always be empty after an SGSN restart.
Sponsored-by: On-Waves ehf
|
|
This function is called to delete an established MM context
silently without invoking a detach procedure.
It is called when a subscriber is cancelled by the HLR. This
generally happens, when an MS has moved to another routing area and
has to use another SGSN.
Sponsored-by: On-Waves ehf
|
|
This commit adds a new authorization policy 'remote' and uses
the subscriber cache for authorization when this policy is being used.
Note that there is no remote backend implemented yet. After the
IMSI/IMEI have been acquired, a request would be sent to the remote
peer. The attach/auth-ciph procedure continues when authorization
info has been received from the peer. This means, that
gprs_subscr_update() must be called then to tell the GMM layer
that it can proceed. A later commit will add VTY commands to do this
manually.
Sponsored-by: On-Waves ehf
|
|
This patch adds GPRS specific functions for gsm_subscriber objects
(allocation, retrieval, deletion) and subscriber data
requests/updates. The sgsn_update_subscriber_data callback is used to
notify the sgsn about updates and is extended by a parameter that
passes a reference to a gsm_subscriber.
Sponsored-by: On-Waves ehf
|
|
Currently the keep_subscr flag in gsm_subscriber_group refers to a
whole group of subscribers which makes it difficult to really delete
single entries if the flag is set.
This patch adds a keep_in_ram field to gsm_subscriber which allows for
keeping subscriber objects in RAM while deleting others.
Note that really deleting an entry requires that both flags
(subscr_group->keep_subscr and subscr->keep_in_ram) are set to 0. So
only the latter should be used if a specification requires the
deletion of a subscriber entry.
Sponsored-by: On-Waves ehf
|
|
Remove warnings related to the SGSN specific code.
Sponsored-by: On-Waves ehf
|
|
This commit adds test for the generic part of gsm_subscriber like
reference counting and flag usage.
Sponsored-by: On-Waves ehf
|
|
Currently every subcriber object directly refers to the gsm_network
which contains a flag shared by every related subscriber
(keep_subscr). This adds a dependency on gsm_network even if only the
function defined in gsm_subscriber_base.c are used.
This patch adds a new struct gsm_subscriber_group which contains the
keep_subscr flag and a back reference to the network object. The
latter is not dereferenced in gsm_subscriber_base.c, so it can safely
be set to NULL when only that part of the gsm_subscriber API is being
used. It also changes that API to use gsm_subscriber_group instead of
gsm_network parameters.
Since there are some places where a pointer to the gsm_network is
needed but where only a gsm_subscriber is available, a 'net' back
pointer is added to the group struct, too. Nevertheless subscr group
and network could be separated completely, but this is not the topic
of this commit.
Sponsored-by: On-Waves ehf
|
|
Related: SYS#798
|
|
Add a command and test to see the current channel load and
available channels per BTS.
Related: SYS#798
|
|
The commit "sgsn: Don't send XID reset after Detach Accept" fixed the
SGSN to not respond to a Detach Accept message when there is no MM
context.
This patch adds a test case to verify, that there is really no
message sent in that case.
The test fails when the commit mentioned aboved is reverted.
Sponsored-by: On-Waves ehf
|
|
Currently the expected P-TMSI generated by the SGSN is hard-coded
into the test. This adds a dependency on the implementation of rand()
and thus the libc used. This breaks the test e.g. on FreeBSD.
This patch modifies test_gmm_attach() to srand(1) first, generate the
P-TMSI, and finally srand(1) again before starting the test.
Sponsored-by: On-Waves ehf
|
|
Currently when the MS does a re-attach without doing a proper detach
first, the gbproxy uses the old local TLLI if patching and the keep
mode are enabled. This leads to a failing attachment procedure when
TLLI patching is also enabled.
This patch changes gbproxy_update_link_state_ul to reset all TLLIs
within the link_info if the message contains an unknown TLLI and an
MI. This is generally the case with Attach Request messages.
The gbproxy_get_link_info_ul gets an additional tlli_is_valid
output parameter that is set, when a TLLI was present and found.
This flag is then used instead of checking tlli.current == 0 to
set TLLI/P-TMSI e.g. Attach Requests when a link_info was already
present for the P-TMSI/IMSI used in such a request.
Ticket: OW#1324
Sponsored-by: On-Waves ehf
|
|
|
|
Increase the bcch_change_mark and generate a new copy of the
system information. Make the method public, add a small test
case. Manually verified using the FakeBTS. I don't know if
the MS will re-read these SIs.
Related: SYS#739
|
|
Allow to set the cell-identity through the control interface
and add a small test for it.
Related: SYS#739
|
|
This will drop a specific IP based BTS. It will lead to a
re-connect of the BTS and the new settings will be applied
then.
Fixes: SYS#737
|
|
The session name must be present in a SDP file. The RFC proposes
to use a space for it but the other equipment is using the dash
so I have picked that as well.
RFC 4566:
The "s=" field is the textual session name. There MUST be one and
only one "s=" field per session description. The "s=" field MUST NOT
be empty and SHOULD contain ISO 10646 characters (but see also the
"a=charset" attribute). If a session has no meaningful name, the
alue "s= " SHOULD be used (i.e., a single space as the session
name).
Fixes: RT#2196
|
|
Equipment like AudioCode appears to get upset when we use a
builtin type and then assign a name to it. Allow to completely
omit the name.
|
|
Currently the function in sgsn_auth.c either have an sgsn_config or
an sgsn_instance parameter. Since then global sgsn variable is
already being used in that file and since other parts of the SGSN
related code also rely on a global sgsn singleton, these parameters
pretend to provide a flexibility that is not really supported.
Therefore this patch removes these parameters except for the ACL
related functions, which do not call code that uses the sgsn
variable.
Sponsored-by: On-Waves ehf
|
|
Currently every time an RA Update Req or an Attach Req is processed, a
new P-TMSI is allocated. When an MS issues another of these messages
before it has completed the first procedure, old_ptmsi is replaced by
ptmsi (and thus lost) and ptmsi is replaced by the newly allocated
P-TMSI. This can confuse the gbproxy, which can loose track of the
logical link then. At least a Blackberry emits a double set of RA Upd
Req messages from time to time which may be just 20ms apart.
This patch adds a check whether mm->ptmsi or mm->old_ptmsi are set.
If both are set, the P-TMSI is not re-allocated. This is only the
case, when the Complete message has not been received yet, since that
message will reset old_ptmsi.
Sponsored-by: On-Waves ehf
|
|
Currently, the LLME is not cleaned up after sending an RA Update
Reject. This happens after entering a routing area from outside,
since in that case the SGSN sends an RA Update Reject (implicitly
detached) which causes the MS to restart the attach procedure.
The LLME is also not updated if an Attach Request with message errors
(encoding, invalid MI type) is received or if an MM context cannot be
allocated.
This patch changes gsm48_rx_gmm_ra_upd_req and gsm48_rx_gmm_att_req
to unassign the LLME or free the MM context (if available) after a
Reject message has been sent.
Ticket: OW#1324
Sponsored-by: On-Waves ehf
|
|
Currently the VTY 'auth-policy' command results in setting or clearing
the acl_enabled flag. This also enables the matching of the MCC/MNC
prefix of the IMSI.
This patch adds an additional policy 'acl-only' which disables the
MCC/MNC matching and relies on the ACL only.
Sponsored-by: On-Waves ehf
|
|
This patch adds some basic SGSN tests to vty_test_runner.py:
- check for config tree nodes
- check specific show commands
Sponsored-by: On-Waves ehf
|
|
Currently the IMSI is only checked immediately when an Attach Request
is received that contains an IMSI IE. If it contains a P-TMSI
instead, access is always granted.
This commit moves the IMSI check to gsm48_gmm_authorize where it is
applied when IMSI and IMEI have been acquired. This fixes the
authorization when the Attach Accept doesn't contain an IMSI.
Sponsored-by: On-Waves ehf
|
|
Currently the GMM state is set to GMM-REGISTERED when an Attach
Accept or a RA Update Accept message is sent, even if a new P-TMSI is
included. In this case 04.08 requires (see 4.7.3.1.3 and 4.7.5.1.3),
that the state is set to GMM-COMMON-PROCEDURE-INITIATED when the
Accept is sent. When the Complete is received, the SGSN shall set
the state to GMM-REGISTERED.
This patch modifies the state updates accordingly.
Sponsored-by: On-Waves ehf
|
|
Currently libcommon depends on libbsc, because gsm_network_init
(libcommon/gsm_data.c) directly calls gsm_net_update_ctype
(libbsc/gsm_04_08_utils.c).
This patch moves gsm_network_init to a new file libbsc/net_init.c.
Sponsored-by: On-Waves ehf
|
|
This test checks the attach procedure until the Attach Complete is
received.
Note that authorization and GMM state updates are not working
properly yet.
Sponsored-by: On-Waves ehf
|
|
This replaces serveral occurences of duplicated code for message
creation and sending (passing to gsm0408_gprs_rcvmsg) into a single
function. In addition, the sgsn_tx_counter is always reset within
send_0408_message to simplify the code that checks for the number of
messages sent.
Sponsored-by: On-Waves ehf
|
|
Allow to set the LAC of the BTS through the CTRL interface.
The change will not be effective immediately.
Fixes: SYS#738
|
|
Add new test message sequences:
- Normal attach (with IMSI) after detach (ok)
- Normal attach (with local TLLI) after detach (ok)
- Unexpected attach (with IMSI) after successful TLLI validation (fails)
- Unexpected attach (with P-TMSI) after successful TLLI validation (fails)
Ticket: OW#1324
Sponsored-by: On-Waves ehf
|
|
Currently the LLME is not deleted when a GMM Status message is
received for which a mmctx cannot be found. This can fill the LLME
list with unneeded entries.
This patch adds code to unassign the LLME in that case.
Ticket: OW#1324
Sponsored-by: On-Waves ehf
|
|
Some switches do not like to receive the IPA PING/PONG messages.
Allow to disable the handling with "no timeout-ping" and create
test cases that verify the switching between the modes. Change the
code to trat <= 0 as an invalid timeout.
Fixes: SYS#713
|
|
Currently, when a Detach Request is received with an unknown TLLI,
it is answered by another Detach Request (!), even when a power_off
Type is used.
This patch uses gsm48_rx_gmm_det_req to handle the message instead.
So this function is changed to cope with a NULL mmctx. In that case
it doesn't unassign the llme, so this must be done manually
afterwards.
Sponsored-by: On-Waves ehf
|
|
Currently, every time the SGSN received a Detach Request from the MS
via an established logical link, it is answered by a Detach Accept.
This violates the specification (GSM 04.08, 4.7.4.1.2 and .3), which
states, that it should only be sent, if "the detach type IE value
indicates that the detach request has not been sent due to switching
off".
This patch adds a conditional to limit the sending of Detach Accept
accordingly.
Sponsored-by: On-Waves ehf
|
|
Currently only a Detach Request (MO) message with power_off = 0 is
checked.
This commit adds a new test case with power_off set to 1. It also
adds checks for the number of messages generated by the SGSN to
verify that these messages are handled differently.
Note that the handling of power_off isn't implemented yet. Therefore
the corresponding assertion is being disabled yet.
Sponsored-by: On-Waves ehf
|
|
This refactores serveral code lines needed for the allocation of MM
contexts into the new function alloc_mm_ctx.
Sponsored-by: On-Waves ehf
|
|
Currently the ACL code is located in sgsn_vty.c.
This commit moves this to a new file sgsn_auth.c as a first step to
make authorization more flexible in order to implement remote
acquisition on subsciber data.
Sponsored-by: On-Waves ehf
|
|
Currently the P-TMSI IE in PAGING_PS is not patched.
This commit adds code to patch BSSGP P-TMSI IE in
gbproxy_patch_bssgp independently from the P-TMSI patching at the LLC
layer. It also extends gbproxy_update_link_state_dl to use the IMSI
to find the link_info if the TLLI is not present in the message.
Note that the spec (GSM 08.18, 7.2) requires to use of the P-TMSI
instead of the IMSI to select the MS if that IE is available.
Nevertheless as long as the IMSI is always present in downlink BSSGP
messages and as long as the optional P-TMSI refers to the same MS
(which is the case currently), this is not an issue.
Sponsored-by: On-Waves ehf
|
|
Currently, when P-TMSI patching is enabled, a new BSS P-TMSI is
generated for each Attach Accept. So two duplicated, subsequent
Attach Accept messages will be mapped to different BSS side P-TMSI.
Because the last one will replace former ones in the link_info
struct, the MS will fail to access the SGSN if it uses the former
P-TMSI to derive the new TLLI.
This patch checks the SGSN P-TMSI already assigned to the link_info
and only generates a new BSS P-TMSI on mismatch (or if the BSS P-TMSI
hasn't been set yet).
Ticket: OW#1322
Sponsored-by: On-Waves ehf
|
|
This adds a test case to check gbproxy's behaviour when processing
two subsequent but identical Attach Accept messages.
Ticket: OW#1322
Sponsored-by: On-Waves ehf
|
|
This patch adds assertions to check the LLC/GMM message received from
the gbproxy by the test framework within the function
test_gbproxy_keep_info.
It also fixes the source address of the DETACH ACC messages.
Sponsored-by: On-Waves ehf
|
|
Coverity complains about having side effects in OSMO_ASSERT argument
expressions. This would be an issue in this case, because that
variable is only reference in other OSMO_ASSERT expressions.
Nevertheless this patch changes this to assign the variable outside
of OSMO_ASSERT.
Fixes: Coverity CID 1244239
Sponsored-by: On-Waves ehf
|
|
Currently one regexp ('patching') is used for all matching.
This patch adds a second category 'routing' which is exclusively used
for SGSN selection. It also adds a corresponding VTY command:
- match-imsi patching RE : MS related patching (currently APN)
- match-imsi routing RE : Select secondary SGSN on match only
- no match-imsi : Clear all filter expressions
Ticket: OW#1258
Sponsored-by: On-Waves ehf
|
|
Currently, patch filter configurations are leaking between tests.
This adds a call to gbproxy_clear_patch_filter() to the end of each
test that calls gbproxy_set_patch_filter().
Sponsored-by: On-Waves ehf
|
|
The current implementation makes it difficult to add further match
expressions.
This patch adds a new struct gbproxy_match that contains the fields
needed for each match expression. The matches (config) and the
results (link_info) are stored in arrays. All related functions are
updated to use them. The old fields in the config structure are
removed.
Sponsored-by: On-Waves ehf
|
|
This patch adds assertions to check the LLC/GMM message received from
the gbproxy by the test framework within the function
test_gbproxy_ra_patching.
Sponsored-by: On-Waves ehf
|