| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Speech codings which are not supported by BTS will be removed from the
bearer capability information element after parsing. This way it is not
required for the MNCC application to consider support of each BTS.
Only GSM full rate is supported by default.
|
|
This option is a workarround for a bug found in Nokia InSite BTS firmware
version 3.0.0. There is no RELease CONFirm message for local end release.
Nokia MetroSite with firmware version 4.178.16 is not affected.
TS 04.06 Chapter 5.4.4.4 "Local end release procedure" states that a
confirm must be sent by layer 2 when receiving a local end release
request.
In order to correctly switch a channel (handover or assignment), local
end release is required.
|
|
Currently, all timestamps are force to SeqNo*d + C which is more than
required by the nanoBTS which seems to be sensitive to alignment
errors only (dTS != k*d, d = ptime * rate = 160).
This patch replaces the force_constant_timing feature by a
force_aligned_timing feature. The timestamp offset will only be
changed (and timestamp errors counted) when the alignment does not
match to the raster based on ptime (default 20ms).
The VTY interface does not change.
Sponsored-by: On-Waves ehf
|
|
Decoding and encoding of FR and EFR TRAU frames are put into seperate
functions. CRC check is done to detect bad EFR TRAU frames.
The test case includes FR and EFR transcoding.
EFR support was tested with Nokia InSite BTS and Siemens BS11.
|
|
Currently the SDP 'ptime' media attribute is never set in generated
MGCP responses.
This patch optionally includes the 'ptime' attribute if
packet_duration_ms is != 0. This behaviour can be enabled/disabled
by using the VTY command "sdp audio-payload send-ptime" (enabled by
default).
Sponsored-by: On-Waves ehf
|
|
Currently the local connection options have been stored as a string.
This patch replaces this string by a struct (that still contains a
string) along with the parsed fields (only the packetization period
at the moment).
It also re-adds the calls to set_local_cx_options() to the
handle_create_con() and handle_modify_con() functions. Except for
the test program this has no side effects, since the LCO values
aren't used yet.
|
|
Since the packet duration is given in ms with the 'ptime' RTP media
attribute and also with the 'p' MGCP local connection option, the
computation is changed to use this value (if present). The
computation assumes, that there are N complete frames in a packet and
takes into account, that the ptime value possibly had been rounded
towards the next ms value (which is never the case with a frame length
of exact 20ms).
Sponsored-by: On-Waves ehf
|
|
This forces the output timing to fulfill
dTS = dSegNo * fixedPacketDuration
where dSegNo = seqNo - lastSeqNo.
If timestamp patching is enabled, the output timestamp will be set
to lastTimestamp + dTS. This kind of relative updating is used to
handle seqNo- and timestamp-wraparounds properly.
The updating of timestamp and SSRC has been separated and the patch
field of mgcp_rtp_state has been renamed to patch_ssrc to reflect
it's semantics more closely. The offset fields are now used always
and will change the corresponding header field if they are != 0.
Ticket: OW#1065
Sponsored-by: On-Waves ehf
|
|
Currently the output SSRC is always forced to be the same if SSRC
patching is enabled.
This patch modifies this to optionally restrict the number of SSRC
changes that will be corrected.
Note that the configuration only allows for the 'once' mode and 'off'.
Sponsored-by: On-Waves ehf
|
|
This patch adds a packet_duration field to mgcp_rtp_state which
contains the RTP packet's duration in RTP timestamp units or 0, when
the duration is unknown or not fixed.
Sponsored-by: On-Waves ehf
|
|
This adds datastructures and a VTY frontend to configure the
different type of RTP header patching: SSRC and timestamp.
Note that timestamp patching is not yet implemented.
Sponsored-by: On-Waves ehf
|
|
So far the payload type used in RTP streams has been taken from the
trunk configuration in NAT mode.
This patch changes the implementation to use the payload type
announced in the SDP part of MGCP messages and responses. SDP
descriptions more than one m=audio line are not yet supported
properly (always the last one is taken).
Ticket: OW#466
Sponsored-by: On-Waves ehf
|
|
The current implementation increments the seqno but does not increment
the RTP timestamp, leading to two identical timestamps following one
after the other.
This patch fixes this by adding the computed tsdelta when the offset
is calulated. In the unlikely case, that a tsdelta hasn't been
computed yet when the SSRC changes, a tsdelta is computed based on
the RTP rate and a RTP packet duration of 20ms (one speech frame per
channel and packet). If the RTP rate is not known, a rate of 8000 is
assumed.
Note that this approach presumes, that the per RTP packet duration
(in samples) is the same for the last two packets of the stream being
replaced (the first one).
Sponsored-by: On-Waves ehf
|
|
This patch modifies the patch_and_count() function to check for RTP
timestamp inconsistencies. It basically checks, whether dTS/dSeqNo
remains constant. If this fails, the corresponding counter is
incremented. There are four counter for this: Incoming and outgoing,
each for streams from the BTS and the net.
Note that this approach presumes, that the per RTP packet duration
(in samples) remains the same throughout the entire stream. Changing
the number of speech frames per channel and packet will be detected
as error.
In addition, the VTY command 'show mgcp' is extended by an optional
'stats' to show the counter values, too.
Ticket: OW#964
Sponsored-by: On-Waves ehf
|
|
GSM 12.21 specifies that "No elementary procedure shall be
initiated to an object instance which has not yet replied to
a previously initiated elementary procedure with a response,
an ACK or a NACK within a layer 3 time-out. The layer 3
timeout for ACK, NACK and responses shall have a default value
of 10 seconds."
We are using this flag in the BTS to enforce/safe-guard
this situation.
|
|
These functions are currently located in libmsc/gsm_04_08.c together
with other symbols that (transitively) depend on many external
symbols (and thus libraries) that aren't otherwise needed by e.g.
osmo-bsc.
Since gsm48_tx_mm_serv_ack() will be needed by osmo-bsc, these
functions are moved to avoid the dependency on gsm_04_08.o.
Sponsored-by: On-Waves ehf
|
|
This reverts commit 61bd965b04e4f00eaf4196eebb4ec6269926d551.
No, we should not link to dbi.. and these libraries..
|
|
The MS do not show the USSD messages yet. This patch modifies the
implementation to insert a CM Service Accept before the ussdNotify
to finish the establishment of the MM connection according to
3GPP TS 04.10/3.2.1.
This fix has been tested with a Blackberry phone that has shown
an ussd_grace_txt after rf_locked has been set to '1'. Without this
patch, that message wasn't shown. The phone has sent a CC Setup
and other messages before processing the channel release message sent
by the BSC, but these messages have not been forwarded to the MSC (as
expected).
Ticket: OW#957
Sponsored-by: On-Waves ehf
|
|
Remove ournode_exit_cmd, ournode_end_cmd, and bsc_install_default()
since this functionality is provided by the current libosmocore.
Replace calls to bsc_install_default() by call to
vty_install_default() with the following semantic patch:
@rule1@
expression N;
@@
- bsc_install_default(N);
+ vty_install_default(N);
Ticket: OW#952
Sponsored-by: On-Waves ehf
|
|
When the PCU is activating a channel we don't want to tell the
BSC using RSL. Add a flag so we can keep track of who asked for
the activation/release of the channel.
|
|
This checks the behavior of the gbproxy when the BSS peer changes the
NSEI and the NSVCI. It also tests BVC_RESET and other UNITDATA
messages after these changes between BSS and SGSN and vice versa (via
the gbproxy).
Ticket: OW#874
Sponsored-by: On-Waves ehf
|
|
This adds the option to delete all BVC peers and/or NS_VC with a
given NSEI with a single command. Static (configured) NS-VC are not
affected. In addition, all connections for this NSEI that can be
deleted by this command can be listed without deleting them by
appending 'dry-run' to the command.
Sponsored-by: On-Waves ehf
|
|
This just deletes the peer entry based on NSEI and BVCI. The NS-VC
are not touched.
|
|
This adds a test with a UNITDATA SGSN message that is addressed to an
invalid (unknown) BVCI. The test shows, that the message is echoed to
the SGSN.
Sponsored-by: On-Waves ehf
|
|
This adds counters that are incremented when errors are detected.
It also modifies the VTY command 'show gbproxy' so that
'show gbproxy stats' shows the counters.
Sponsored-by: On-Waves ehf
|
|
Currently in most places in gb_proxy.c a reference to a NS-VC object
is used where the peer is meant instead. The patch changes this by
using the NSEI instead in these cases.
Sponsored-by: On-Waves ehf
|
|
This program tests the gbproxy implementation by passing NS messages
to a modified gbproxy that dumps the resulting messages, signals, and
state.
It focusses on testing abnormal situations like port changes.
Ticket: OW#874
Sponsored-by: On-Waves ehf
|
|
The database code should not know about the network. Move the
setting of the network pointer into the subscriber layer.
|
|
|
|
The jenkins runs make distcheck in the default configuration and
not with the nat enabled.
DISTCHECK_CONFIGURE_FLAGS="--enable-nat" make distcheck
|
|
This adds in-place patching of the time information in the
MM INFORMATION message. The timezone in the 'Local time zone' and
the 'Universal time and local time zone' information elements
and the offset in the 'Network Daylight Saving Time' information
element are optionally set.
The new values are determined by the 'timezone' vty command in the
config_net_bts node. That command is extended by an optional
DST offset parameter.
Tests are provided for the vty part and for the plain
bsc_scan_msc_msg() function.
Sponsored-by: On-Waves ehf
Ticket: OW#978
|
|
This stores the last SET rf_locked control command along with a
timestamp. The 'show network' vty command is extended to show
this information.
Ticket: OW#659
|
|
Send an USSD message to the mobile station requesting a connection
for a call or a SMS when the link to the MSC is down or in the
grace period.
The messages can be set (and this feature activated) by setting
bsc/missing-msc-text resp. msc/bsc-grace-text via the vty.
The generation of both messages has been tested manually.
Ticket: OW#957
|
|
In case of the RLSD coming from the MSC we are patching the address
in-situ but for local calls set con = NULL. We then answered the RLSD
with the wrong reference and the MSC kept on trying.
|
|
Assign a static name to a MSC Connection and use it. In case there
are multiple connections we can now more easily identify them.
This is only used for the NAT right now, the BSC could start to
name the various MSC connections too.
|
|
Add bsc_install_default() and replace all install_default()
This patch adds bsc_install_default() which calls install_default()
and add 'exit' and 'end'. All other calls to install_default() are
replaced by calls to bsc_install_default().
Since 'exit' and 'end' are now added automatically to each node, the
explicit registrations of these commands are removed by this patch,
too.
The related tests succeed now without work-arounds (except for the
'config' node itself which is part of libosmocore).
|
|
Rename methods to be like bsc_ussd_ACTION.
|
|
Send an USSD message on each MS connection if the connection to
the MSC has been lost.
Add a vty config command 'bsc-msc-loss-txt' in 'config-msc' to set
the notification string and to enable the feature.
Ticket: OW#957
|
|
This enum indicates if the mgcp is running on the BSC or the BSC-NAT.
|
|
* The post-routing is applied after the first re-writing. To do this
the new number is copied back into the called data structure.
* Add a testcase that goes from 0172 to 0049 and then back to 0049
using the post rule with a table lookup.
|
|
* Increase the rewritten rule to five digits (this is the easiest
for the unit test). This will add another 40kb to the runtime size.
* Create a unit test that tests adding and removing the prefix rules.
* Use the regexp match to replace from one package
|
|
* It is a trie. The max depth of the trie is the length of the
longest prefix. The lookup is O(lookuped_prefix), but as the prefix
length is limited, the lookup time is constant.
* Each node can hold the entire prefix, has place for the rewrite
rule with up to three digits.
* A trie with 20k entries will take about 3MB ram.
* Filling the trie 100 times takes ~800ms on my i7 laptop
* 10.000.000 lookups take 315ms.. (for the same prefix).
* 93/99 lines are tested, 6/6 functions are tested, 49 of 54 branches
are tested. Only memory allocation failures are not covered
* A late addition is to handle the '+' sign and to increase the number
of chars in the rewrite prefix. The timing/line coverage has not
been updated after this change.
|
|
Disable the periodic LU using "no periodic location update" VTY
command. In that case set the expire_lu to 0 which will then be
translated to a NULL in the database layer. This leads to a bit of
copy and paste in the db_sync_subscriber method but I don't see
how we could easily use 'datetime(%i, 'unixepoch')' and 'NULL'
at the same time.
Change the query to find expired queries to check for NOT NULL
and the time being in the past. This means if there are still
old subscribers in the database they might not be expired. One
would need to execute a query like "UPATE Subscriber SET expire_lu
= 0 WHERE expire_lu is null". The same applies when disabling the
periodic LU. One would need to update the database by hand.
Manual tests executed/passed:
1.) periodic LU enabled:
* use gst LUTest.st to do a LU
* UPDATE Subscriber SET expire_lu=datetime('now');
* observe the subscriber being expired (it was)
2.) periodic LU disabled:
* use gst LUTest.st to do a LU
* verify that the expire_lu is NULL in the database
|
|
We were expiring subscribers during active calls. This is because
the T3212 is stopped under certain conditions but we didn't stop
that timer at all.
Remember if T3212 timer was stopped due something done by NITB and
update the expiration time at the end of the radio connection, as
the phone should restart it when returning to MM Idle.
It is a bit difficult to decide when we should set the flag. E.g.
in a CM Service Request we don't know if we accept the service and
during a LU we already send MM messages before we accept or reject
the subscriber.
The easiest is to set the flag when receiving a paging response
on known subscribers and at the end of the authentication process.
Do not expire a subscriber that has an active connection that is
marked with the flag, e.g. we would still expire a subscriber that
is being paged.
Manual tests executed/passed:
* gst LUTest.st verified that a expiration date was set
* gst SMSTest.st (doing another LU but forcing a timeout on the
SMS sending). Verified that the expire_lu was updated.
|
|
|
|
This adds a minimalistic ACL by which certain, individual roaming IMSIs
can be authorized to use the SGSN. So you can selectively bypass the
'MCC+MNC == first 5 digits of IMSI' checking for a couple of IMSIs
|
|
A CM service request must be acknowledged also, when encryption is already
enabled.
Without encryption enabled, the security status is GSM_SECURITY_NOTAVAIL,
which causes a CM service acknowledge. On initial CM service request, the
security status is GSM_SECURITY_SUCCEED, if encryption is enabled. This
will not lead to an acknowledge, because the cyphering command implies an
acknowlege. An additional CM service request requires an acknowledge, so
I added a new security status: GSM_SECURITY_ALREADY
|
|
This patch replaces the field 'is_transcoded' in the mgcp_endpoint
structure by the enum mgcp_type, that can be further extended with
new types.
|
|
elements.
Original code was inconsistent about lengths and could lead to out
of bounds write. Lengths were also inconsistent with the TS 24.008.
Fixes: Coverity CID 1040714.
|
|
The support has been implemented for an old model, we were told that
newer versions would be made incompatible with OpenBSC. Ther are
various warnings in the code and coverity has found some new ones.
Just remove the code as we don't know of anyone using this code.
|
